To provide the design and engineering elements of the United States Navy, the Royal Navy and Canadian Forces (Sea Element) with standard reference values for use in reporting mechanical vibration levels.

ABC-STD-38 - Methods For Specifying And Calibrating Shock And Vibration Instruments

To provide the Royal Navy, the Royal Canadian Navy, and the United States Navy with standard methods for specifying the characteristics of shock and vibration measuring instruments and standard methods for their calibration.

ABC-STD-4 - Electrical Frequencies And Voltage (S/S By Abc-Std-52)

ABC-STD-40 - Packaging, Packing And Container Marking Of Semi-Conductor Devices

ABC-STD-44 - Comparative Compilation Of Aluminum Alloys For Interchangeability/Equivalency

ABC-STD-47 - Lubricating Fittings For Shipboard Use

ABC-STD-48 - General Principles Of Gauging

ABC-STD-50 - Surface Texture

ABC-STD-51 - Comparative Compilation Of Copper Alloys For Interchangeability/Equivalency

ABC-STD-52 - Shipboard Electrical Power Characteristics

ABC-STD-53 - Electrical Connectors For Portable Fire And Damage Control Pumps

ABC-STD-54 - Steel Ships Plates

ABC-STD-56 - Silicone Insulated Electric Power And Control Cables

ABC-STD-57 - Table Of Comparability Of Definitions Of Terms (Preservation-Packaging, Packing And Marking)

ABC-STD-58 - Table Of Comparability For Methods And Submethods Of Preservation (For Packaging)

ABC-STD-6 - Boiler Water Treatment Chemicals

To enhance the joint operations and supply-support of the United States Navy, the Royal Navy, the Canadian Forces and the Royal Australian Navy by providing standard boiler water treatment chemicals or compounds.

ADV-PUB-20/25 - Interoperability Of Aircraft Stores

The object of the ADV PUB is to maintain a ready reference on aircraft stores interoperability information to identify additional cross-servicing opportunities.

ADV-PUB-20/26 - Aircraft Stores Interface Manual

The object of the ADV PUB is to provide a publication which will facilitate aircraft/aircraft stores compatibility analysis.

ADV-PUB-25/38 - Aircraft Electrical Support

This publication provides information and guidance on the subjects shown for each part listed below: Part 1 - Electrical Power Supplies at Hardstandings, Part 2 - Interchangeability of Tinned Copper Terminals, Part 3 - Interchangeability of Cable Splices (In-Line Connectors) Tinned Copper.

ADV-PUB-25/39 - Methods And Agents Used For Cleaning Oxygen Systems

The object of this Advisory Publication is to inform ASCC nations of the cleaning methods and agents used for the oxygen systems of member nations?? aircraft, with the view of ensuring in the event of a member nation requiring to clean the oxygen system of another nation's aircraft, it could be done without risk of contaminating the system through the use of suspect materials and methods.

ADV-PUB-25/40 - Techniques Of Sampling & Analysis Of Gases & Liquified Gases For Aircraft Servicing

The object of this Advisory Publication is to provide a unified compendium of the specialized techniques and equipment used in gaseous and liquefied gas sampling, analysis, and equipment calibration.

ADV-PUB-44/51 - Formats For Requesting And Answering Requests For Air Transport

The purpose of this ADV PUB is to inform participating Member Nations of the message formats used by other participating Member Nations.

ADV-PUB-44/54 - Supply/Equipment Airdrop Systems

The object of this Advisory Publication is to inform ASCC nations of the types, functional characteristics, operating criteria, aircraft and interoperability clearances of supply/equipment airdrop systems, with the view of promoting the interoperability of airdrop systems and airdrop aircraft in service with the member nations.

ADV-PUB-44/55 - Troop Type Personnel Parachutes

The object of the Advisory Publication is to inform ASCC nations of the types, functional characteristics, operating criteria, aircraft and interoperability clearances of troop type personnel parachutes used in airdrop operations, with the view of promoting the interoperability of personnel parachutes and airdrop aircraft in service with the member nations.

ADV-PUB-44/57 - Multi-Modal Documentation Of Cargo

ADV-PUB-50/1 - High Order Languages

The purpose of this agreement is to identify computer High Order Language (HOLs) other than Ada in use by the air arms of all ASCC member nations in the development of operational software for avionic systems.

ADV-PUB-50/11 - Airborne Video Recorders

This Advisory Publication identifies airborne video recorders and ground based playback systems which are being used by the air arms of all ASCC member nations. It is intended to reduce the proliferation of airborne video recorders in avionics systems and to assist in control of video recorders which are approved as standards by the various nations.

ADV-PUB-50/4 - Software Documentation Standards (Issued Controlled)

To identify the latest software documentation standards for the reference and use of all ASCC member nations.

ADV-PUB-50/6 - Avionics System Architecture Guidelines

To identify avionics architecture guidelines which should be considered by the air arms of all ASCC member nations in the development of their individual avionics architectural approaches.

ADV-PUB-50/8 - Computer Resources Handbook For Critical Systems

To provide guidance in the design and development of flight and propulsion control systems to consider the criticality of the functions being performed.

ADV-PUB-50/9 - Multiplex Applications Handbook

To provide avionics multiplex data bus guidelines, which should be considered by the ASCC member nations in the development of their individual avionics architectural approaches.

ADV-PUB-51/8 - Air Drop Rescue Equipment (Sea) (Rel To Other Than Dod Act Req Pri Appr Of Hq Usaf/Xoxx(Iso), Wash Dc 20330-5058)

To exchange information on Air Drop Rescue Equipment (sea) that are used by the member nations.

ADV-PUB-51/9 - Datum Buoys Markers Marine And Flares

To exchange information on the Datum Buoys, Markers Marine and Flares that are used by the member nations.

ADV-PUB-52/22 - Reconnaissance Interoperability Handbook

To assist reconnaissance units of the ASCC nations to cross-service other nations' reconnaissance aircraft and to exploit the imagery they have obtained.

ADV-PUB-61/17 - Vibration Exposure Limits

To provide guidance on the limits to which aircrew and ground support should be exposed to whole body vibration.

ADV-PUB-61/18 - Comparative Anthropometry Of Ascc Personnel For Personal Protective Clothing & Design, Flight Garments

This report demonstrates that body sizes and proportions of aircrew personnel in ASCC member nations are sufficiently comparable for successful exchange of personal-protective clothing and equipment between member nations.

ADV-PUB-61/19 - Guidance For The Control Of Heat Stress In Operations Of High Performance Military Aircraft (Advisory Publication)

To provide a common basis from which member nations will develop more specific hot weather guidelines suitable to their own aircraft and patterns of operation.

ADV-PUB-61/25 - Human Tolerance To Repeated Shock

To provide provisional guidance regarding criteria for exposure of personnel to repeated shocks.

ADV-PUB-61/26 - Standardized Centrifuge G-Stress Profiles For Medical Evaluation Of Aircraft Members

To provide a common standard for centrifuge stress testing to facilitate the interpretation of medical and physiological data from human subjects.

ADV-PUB-61/27 - High Speed Passive And Active Restraint

To provide information and guidance regarding the use of passive and active restraints to reduce limb flail injury during ejections.

ADV-PUB-61/28 - Ejection Seat Initiating Devices

To record and compare the ejection systems initiating devices used in aircraft of ASCC countries.

ADV-PUB-61/29 - Terms & Symbols For Thermal Physiology

To promote uniform terminology and clear communication among the ASCC nations and to assure that reports from WP 61 conform to internationally recognized standards where appropriate.

ADV-PUB-61/30 - Methodology For Measurement Of Core Temperature Using Radio Pills

To provide guidance regarding the use of radio pills for measurement of core temperature.

ADV-PUB-61/31 - Aircrew Entry Hearings Standards

To compare and record the aircrew entry hearing standards of ASCC nations.

ADV-PUB-61/34 - Aeromedical Aspects Of Aircraft Accident/Incident Investigations

ADV-PUB-61/36 - Aircrew Anthropometric Scale Models For Engineering Design

To document the development and use of the AFAMRL Drawing Board Manikins and to describe plans of manikins that can be made to any scale that may be required by an engineer or designer of aircrew and other workstation geometries.

ADV-PUB-61/37 - Anthropometric Limitations For The Selection Of Aircrew And For Aircraft Crew Stations In The Ascc Nations

To facilitate a comparative study of the anthropometric limitations applied to the selection of aircrew across member nations.

ADV-PUB-61/44 - Procedure For Protecting Aircrew During Routine Operations In Coldclimate

To provide a framework upon which to build suitable protective procedures and training programs for cold-weather protection of personnel, addressing problems of cold injury and frostbite as well as the subtler biomedical effects of cold which can significantly impair human performance and increase accident rates.

ADV-PUB-61/46 - Glossary Of Molecular Sieve Oxygen Generation System (Msogs) Terminology

To standardize the terminology used among ASCC countries in communications on molecular sieve type oxgen generation systems.

ADV-PUB-61/49 - Intelligibility Of Speech In Noise

To promote uniformity in the techniques used to measure the intelligibility in noise of voice communication systems when they are used with English-language speech.

ADV-PUB-61/50 - Methods For Assessing Visual Endpoints For Acceleration Tolerance

To provide information regarding current techniques for visual and point standards for the measurement of G tolerance so that G tolerance measurements on different test devices nay be compated.

ADV-PUB-61/51 - Centrifuge Training To Increase High-G Tolerance

To provide a standardized method for training pilots to perform a competent anti-G straining maneuver (AGSM).

ADV-PUB-61/52 - The Anthropometry Of Ascc Male Aircrew Populations

This report recommends methods for documenting, analyzing, and reducing observer error in anthropometric surveys.

ADV-PUB-61/53 - The Optical & Material Requirements For Aircrew Plano Sunglasses

To provide guidance on material and optical requirements for aircrew plano sunglasses.

ADV-PUB-61/55 - Methodology For Assessment Of The Thermal Performance Of Immersion Protective Clothing

To provide guidance on test procedures for the evaluation of the thermal performance of immersion protective clothing.

ADV-PUB-61/56 - Medical Examination Ofaircrew Following An Aircraft Accident/Incident

To advise member nations on the recommended medical investigations and documentation that should be completed following an aircraft accident or incident.

AECTP-100 ED.4 - Environmental Guidelines For Defence Materiel

AECTP-200 ED.4 - Environmental Conditions

AECTP-300 ED.3 - Climatic Environmental Tests

AECTP-400 ED.3 - Mechanical Environmental Tests

AIR-STD-10/10 - Fuel Contents Gauges (Requests Other Than Dod Refer To Hq Usaf/Xoxx, (Iso), Washington, Dc 20330-5058

To standardize the case size, the units of measurement and the broad features of presentation to be used for fuel contents gauges for all aircraft.

AIR-STD-10/11 - Layout Of Flight Instruments

To standardize the layout of flight instruments in fixed and rotary wing aircraft.

AIR-STD-10/12 - Operation Of All Controls And Switches At Aircrew Stations

To standardize the operations of all controls and switches at aircrew stations so that they operate in the same sense.

AIR-STD-10/13 - Engine Controls & Switches In Fixed Wing Aircraft (Rel To Other Than Dod Act Req Pr Appr Of Cnm, Mat 09B21)

To standardize the location, actuation and design of engine controls and switches in fixed wing aircraft.

AIR-STD-10/14 - Location And Grouping Of Electrical Switches

To standardize the location and grouping of various electrical switches.

AIR-STD-10/15 - Location & Actuation Of Airframe Controls In Fixed Wing Aircraft

To standardize the location and actuation of all airframe.

AIR-STD-10/16 - Automatic Flight Control Systems (Afcs)

To standardize controls and other functional areas of Automatic Flight Control Systems (AFCS).

AIR-STD-10/18 - Position Of Map Stowages In Fixed And Rotary Wing Aircraft

To standardize the position of map stowages in pilot's cockpits.

AIR-STD-10/19 - Illumination Of Aircrew Stations

To standardize the aircrew station lighting.

AIR-STD-10/2 - Units Of Measurement

To establish standard units for the display of information in cockpits and aircrew stations.

AIR-STD-10/20 - Location, Actuation & Shape Of Airframe Controls For Rotary Wing Aircraft

To Standardize the location, actuation and shape of airframe controls for rotary wing aircraft.

AIR-STD-10/21 - Position Of Pilot Operated Navigation And Radio Controls In Fixed Wing Aircraft (Issued Controlled)

To standardize the positions of pilot operated navigation and radio controls.

AIR-STD-10/22 - Services Operable From Stick Grips

To standardize the design and services operated from the control stick, in both fixed and rotary wing aircraft.

AIR-STD-10/23 - Emergency Control Colour Schemes

To adopt a standard colour scheme for emergency controls in all aircraft.

AIR-STD-10/25 - Location And Arrangement Of Engine Instructments In Aircraft (Change 1)

AIR-STD-10/3 - Manifold Pressure Gauges

AIR-STD-10/30 - Aircrew Station Warning, Cautionary And Advisory Signals

To standardize the signal used to inform the crew members of conditions which exist relating to the operations of the aircraft and/or its equipment.

AIR-STD-10/32 - Dimensions Of Clock Cases

AIR-STD-10/34 - Mounting Clamps For Aircraft Instruments (Issued Controlled)

To provide interchangeability features for mounting flangeless instrument cases so that clamps produced in the ASCC countries will be interchangeable.

AIR-STD-10/35 - Standard Atmosphere Tables

To provide standard pressure/altitude values to be used in the design and calibration of those aircraft equipments whose operation is a function of atmosphere pressure.

AIR-STD-10/36 - Circular Dial Tachometer (Non Servoed) (Issued Controlled)

To provide standard circular dial tachometers for turbine-engined aircraft.

AIR-STD-10/37 - Evaluation Of Aircrew Information Systems

To standardize methods for evaluation of aircrew information systems.

AIR-STD-10/38 - Principles Of Presentation Of Information

AIR-STD-10/39 - Numbering Of Engines And Their Associated Controls And Displays In Aircraft

To achieve standardization on the method of numbering engines and their associated controls and displays in aircraft.

AIR-STD-10/4 - Accelerometer Indicators

The aim of this agreement is to standardize the presentations, controls, and case sizes of indicating accelerometers.

AIR-STD-10/40 - Location And Actuation Of Thrust Vector Controls For Vstol Aircraft (Issued Controlled)

To standardize the location and actuation of lift/thrust controls for VTOL aircraft other than helicopters.

AIR-STD-10/41 - Airspeed Indicators

To standardize the display and physical requirements for airspeed indicators.

AIR-STD-10/42 - Attitude Indicators (Req Other Than Dod Refer To Hq Usaf/Xoxx (Iso), Washington, Dc 20330-5058

AIR-STD-10/43 - Colours And Markings Used To Denote Operating Ranges Of Aircraft Displays

To standardize the colours used for operating range markings in aircraft displays.

AIR-STD-10/44 - Control Shapes

AIR-STD-10/45 - Horizontal Situation Indicator

To standardize the display and physical requirements for Horizontal Situation Indicators.

AIR-STD-10/46 - Standard Dynamic Pressure Calibrated Airspeed Tables For Aircraft Equipment (Issued Controlled)

To provide standard dynamic pressure/calibrated airspeed values to be used in the design and calibration of those aircraft equipments whose operation is a function of dynamic pressure.

AIR-STD-10/47 - Legends In Aircrew Stations

To standardize nomenclature (words, contractions, abbreviations, acronyms and symbols) used on controls, panels and display in aircrew stations.

AIR-STD-10/48 - Display Of Combat Information

AIR-STD-10/49 - Air To Air Refueling Cockpit Controls And Displays

To standardize the cockpit controls used during probe/drogue and boom/receptacle air-to-air refuelling operations and the display of information given to the pilot.

AIR-STD-10/5 - Turn & Slip Indicators (Issued Controlled)

To achieve standardization of instrument case sizes and presentation of turn and slip indicators in the air forces of the ASCC countries.

AIR-STD-10/50 - Glass, Aircraft Instrument, Lighting Wedge And Cover

AIR-STD-10/51 - Standard Display Nomenclature For Cockpit Instruments (With Amendment 2)

To provide standard display nomenclature for the various elements used in cockpit instruments to display information.

AIR-STD-10/52 - Enviromental Test Methods For Panel Mounted Instruments

AIR-STD-10/53 - External Vision From Aircrew Stations

AIR-STD-10/54 - Attitude Director Indicator

To standardize the display and physical requirements for attitude director indicators.

AIR-STD-10/55 - Aircrew Station Dimensional Design Factors

To establish requirement for aircrew station dimensions to ensure efficient and safe aircraft operation.

AIR-STD-10/56 - Electronically And Optically Generated Displays Formats And Symbology For Fixed Wing Aircraft

AIR-STD-10/57 - Vertical Scale Flight Instruments

To achieve standardization of the presentation of air data on vertical scale instruments in the crew stations.

AIR-STD-10/58 - Aircraft Interior Colour Schemes

AIR-STD-10/59 - Calibration And Accuracy Of Aircraft Barometric Non Servoed Altimeters

To standardize the test procedures and accuracy requirements of aircraft barometric non-served altimeters.

AIR-STD-10/6 - Numerals And Letters For Aircrew Station Displays

To provide standard forms and dimensions of numerals and letters for use on aircrew station fisplays. The adoption of this standard will contribute to complete standardization of the markings on aircrew station displays, such as, instrument dials, control panels, and controls.

AIR-STD-10/60 - Circular Dial Altimeters And Calibration Procedures

To establish general requirements for the display, physical characteristics and calibration for all barometric altimeters and particular requirements for special types.

AIR-STD-10/61 - Coating, Reflection Reducing For Aircrew Station Displays

AIR-STD-10/62 - Aircrew Station Control Panels

To provide criteria for the design, selection and arrangement of control and displays on aircrew station control panels based upon human engineering considerations.

AIR-STD-10/63 - Circular Dial Engine Temperature Indicators (Issued Controlled)

The object of this agreement is to standardize the characteristics of circular dial engine temperature indicators for use in turbine engined aircraft where the imput signal is derived from thermocouples.

AIR-STD-10/64 - Aircraft Mock Up Inspection Techniques

To standardize the types of mock-ups developed for evaluation, the measurement and evaluation techniques employed, and the types of associated aircraft performance and design date to be furnished prior to, during, and following the mock-up evaluations and/or formal inspections.

AIR-STD-10/65 - Aircrew Control Assignments In Fixed Wing Aircraft

AIR-STD-10/66 - Emergency Escape/Evacuation Illumination

AIR-STD-10/67 - Integrated Airspeed & Mach Number Indicators

The object of this agreement is to standardize the display, physical and performance requirements of integrated airspeed and mach number indicators for use in aircraft.

AIR-STD-10/68 - Armour Protection For Aircrews

The object of this agreement is to standardize the desing of armour protection systems, to protect aircrews from the threats posed by enemy ballistic and fragmentation weapons.

AIR-STD-10/69 - Circular Dial Rate Of Fuel Flow Indicators

The object of this agreement is to standardize the characteristics of circular dial rate of fuel flow indicators for use in aircraft.

AIR-STD-10/7 - Dimensions For Instrument Cases

To provide standard instrument cases which will be selected for use with certain indicators when deemed appropriate.

AIR-STD-10/70 - Airborne Radio Control Units

To standardize the controls, displays, layouts and lighting of Airborne Radio Control Units.

AIR-STD-10/72 - Electronic Colour Display Systems

The purpose of this agreement is to standardize the principle of presentation for information generated on electronic color display systems. This standard applies to color CRTs and to other display technologies where appropriate.

AIR-STD-10/8 - Circular Dial - Type Vertical Speed Indicator (Barometric) (Rel To Other Than Dod Act Req Pr Appr Of Cnm, Mat 09B21)

To provide a standard vertical speed indicator.

AIR-STD-10/9 - Machmeters (Rel To Other Than Dod Act Req Pr Appr Of Cnm, Mat 09B21)

To standardize the case size and broad features of presentation to be used in machmeters.

AIR-STD-101/1 - Air Reconnaissance Intelligence Report Forms

AIR-STD-101/11 - Imagery Interpretability Rating Scale (Issued Controlled)

To adopt a standard Imagery Interpretability Rating Scale for use by ASCC Armed Forces.

AIR-STD-101/12 - Reporting Of Data Used For Dimensional Analysis Of Imagery

To Standardize the reporting of data used for dimensional analysis of imgery.

AIR-STD-101/2 - Titling Of Air Reconnaissance, Air Survey & Mapping Imagery

AIR-STD-101/3 - Air Reconnaissance Request/Task Form

AIR-STD-101/4 - Titling Of Hand Held Film

AIR-STD-101/5 - Target Reporting Guide (Issued Controlled)

To standardize and consolidate the vital components in air reconnaissance intelligence reporting derived from air reconnaissance and sensor images.

AIR-STD-101/6 - Air Reconnaissance Intelligence Reporting Nomenclature

AIR-STD-101/7 - The Point Designation Template For Imagery

AIR-STD-101/8 - Minimum Resolved Object Size For Imagery Interpretation

AIR-STD-101/9 - Request Form For Imagery To Be Used In Imagery Interpretation Keys Production

To adopt a standard imagery request form to facilitate requesting imegery from other ASCC member nations for use in umagery interpretation keys production.

AIR-STD-103/1 - Aircraft Arresting Gears For Airfields

AIR-STD-103/2 - Air Traffic Control Procedures For Arrestment Of Aircraft

To ensure that each Member Nation using aircraft arresting systems of other Member Nations can expect Air Traffic Control to comply with a standard procedure.

AIR-STD-103/3 - Signals For Runway Party When Disengaging An Aircraft After A Hook Cable Arrestment

AIR-STD-103/4 - Pilots Operating Procedure For Engagement Of Airfield Arresting Systems

To ensure that each Member Nation using aircraft arresting systems of other Member Nations ulilize the same pilot's operating procedures.

AIR-STD-104/1 - Engineering And Associated Data

AIR-STD-104/10 - Engineering Drawing Titues (Req For Issue From Other Than Dod & Dod Contractors Must Be Sent Via Hq Usaf/Xoxx(Iso) Wash., D.C. 20330-5058

AIR-STD-104/11 - Types Of Engineering Drawings (Req For Issue From Other Than Dod & Dod Contractors Must Be Sent Via Hq Usaf/Xoxx(Iso) Wash., D.C. 20330-5058)

To ensure that each Member Nation can interpret types of engineering drawings included in Engineering and Associated Data from another nation without references to the Design Activity.

AIR-STD-104/12 - Numbering, Coding & Identification Of Engineering Drawings (Req For Issue From Other Than Dod & Dod Contractors Must Be Sent Via Hq Usaf/Xoxx(Iso) Washington, D.C. 20330-5058

AIR-STD-104/13 - Revision Of Engineering Drawings

AIR-STD-104/15 - Microreproduction Of Engineering Drawings & Associated Data (Req From Other Than Dod & Dod Contractors Must Be Sent Via Hq Usaf/Xoxx(Iso) Washington, D.C. 20330-5058

To ensure that each Member Nation can utilize 35mm micro-reproduction of engineering drawings and associated data prepared by another member nation.

AIR-STD-104/16 - Metrication (Req From Other Than Dod & Dod Contractors Must Be Sent Via Hq Usaf/Xoxx(Iso) Washington, D.C. 20330-5058

To achieve compatibility and/or standardization between ASCC member nations in the field of metrication.

AIR-STD-104/17 - 35Mm Aperture (Carrier And Associated Cards (Req For Isssue Other Than Dod Refer To Hq Usaf/Xoxx (Iso), Washington, Dc 20330-5058

AIR-STD-104/18 - Guide For Electrical Maintence Diagrams For Aircraft Systems (Rel To Other Than Dod Act Req Pr Appr Of Cnm, Mat 09B21, Wash, D.C. 20360)

AIR-STD-104/19 - Circuit Identification

To adopt as a standard a common aircraft function letter to identify differenct types of electrical circuits in aircraft.

AIR-STD-104/2 - Graphical Symbology For Use On Engineering Drawings And Associated Data (Issue Controlled)

To ensure that each Member Nation can interpret graphic symbology used on Engineering and Associated Data from another Member Nation without referring to the Design Activity.

AIR-STD-104/20 - Electrical & Electronic Diagrams (Rel To Other Than Dod Act Req Pri Appr Of Hq Usaf/Xoxx (Iso) Wash, Dc 20330-5058)

AIR-STD-104/21 - Dimensioning And Tolerancing (Req From Other Than Dod & Dod Contractors Must Be Sent Via Hq Usaf/Xoxx(Iso) Washington D.C. 20330-5058

AIR-STD-104/22 - Configuration Management Definitions And Abbreviations (Rel To Other Than Dod Act Req Pri Appr Of Hq Usaf/Xoxx-Iso, Wash Dc 20330-5058)

To ensure that member nations can interpret configurations management definitions and abbreviations.

AIR-STD-104/4 - Equipment Index Systems For Master/Original Engineering Drawings

To ensure that each Member Nation can interpret the equioment index sustems used for engineering drawings relating to Engineering and Associated Data from another Member Nation without referring to the Desing Activity.

AIR-STD-104/5 - Definitions For Use On Engineering Drawings And Associated Data

To ensure that each Member Nation can interpret definitions used on Engineering and Associated Data from another nation without reference to the Design Activity.

AIR-STD-104/6 - Engineering Drawing Formats (Req For Issue From Other Than Dod & Dod Contractors Must Be Sent Via Hq Usaf/Xoxx-Iso) Wash Dc 20330-5058

To ensure that each Member Nation can interpret engineering drawing formats used on Engineering and Associated Data from another nation without reference to the Design Activity.

AIR-STD-104/7 - Engineering Drawing Practices (Req For Issue From Other Than Dod & Dod Contractors Must Be Sent Via Hq Usaf/Xoxx(Iso), Wash., D.C. 20330-5058

To ensure that each Member Nation can interpret engineering drawing practices used on Engineering and Associated Data from another Member Nation without referring to the Design Activity.

AIR-STD-104/8 - Engineering & Associated Data Lists (Req For Issue From Other Than Dod & Dod Contractors Must Be Sent Via Hq Usaf/Xoxx(Iso), Wash., D.C. 20330-5058)

To ensure that each Member Nation can interpret engineering and associated data lists used in Engineering and Associated Data from another Member Nation without referring to the Design Activity.

AIR-STD-104/9 - Abbreviations For Use On Engineering Drawings & Associated Data (Req For Issue From Other Than Dod & Dod Contractors Must Be Sent Via Hq Usaf/Xoxx(Iso) Wash Dc 20330-50

To ensure that each Member Nation can interpret the abbreviations used on Engineering and Associated Data from another nation without references to the Design Activity.

AIR-STD-11 - Aircraft Maintenance (Working Party 11) Changes To

AIR-STD-11/1 - Aircraft Servicing/Hazard Markings

To identify and standardize servicing and hazard markings on aircraft used by member nations.

AIR-STD-11/10 - Replenishment Of Engine Thrust Augmentation Systems

AIR-STD-11/12 - Pressure Replenishment Of Engine Oil

AIR-STD-11/13 - Aircraft Cross Servicing

To provide the essential information to facilitate cross-servicing of member nations' operational aircraft by the forces of the other ASCC nations.

AIR-STD-11/14 - Aircraft Hydraulic System Servicing (Change 6 - 1 Feb 79) S/S By Air-Std -11/14

To standardize the basic requirement for hydraulic systems replenishment and activation to facilitate the cross-servicing of each member Nation's aircraft.

AIR-STD-11/15 - Aircraft Tire Servicing (Rel To Other Than Dod Act Req Pr Appr Of Cnm, Mat 09B21)

AIR-STD-11/16 - Cross Servicing Information To Be Carried In Aircraft

To provide specified servicing information in the aircraft to facilitate cross-servicing.

AIR-STD-11/17 - Ground Air Conditioning Of Aircraft & Aircrew Equipment

To provide sufficient data on ground Cooling and Heating equipment available in the Services of the five Nations, to enable the Air Force of each Nation to judge whether the essential facilities are likely to be available for turn-around of their own aircraft, and/or for maintenance at a state of readiness.

AIR-STD-11/18 - Availability Of Cross-Servicing Support On Selected Airfields No S/S Document)

To provide cross-servicing facilities on selected airfields to meet the anticipated operational emergency requirements of the ASCC Nations.

AIR-STD-11/19 - Cross-Servicing Of Bail-Out And Walk-Around Oxygen Bottles

AIR-STD-11/2 - Removal And Replacement Of Aircraft Fuel Tank Caps And Fuel Tank Cap Access Covers

AIR-STD-11/20 - Aircraft Cross-Servicing Guides

To establish scope and standard formats for providing guides to facilitate the cross-servicing of Member Nations' aircraft by the forces of other ASCC Nations.

AIR-STD-11/3 - Aircraft Fuelling

To establish standards for fuelling aircraft.

AIR-STD-11/4 - Testing Of Aircraft Pressure Cabins

AIR-STD-11/5 - The Aperture Of The Terminal Ring Or Link Of Aircraft Lifting Slings 020768

AIR-STD-11/6 - Defuelling Of Aircraft (Change 2 - 20 Jan 78)

AIR-STD-11/7 - Jacking Of Aircraft (S/S By Air-Std-25/23)

To standardize on primary jacking requirements to achieve cross-servicing capability including tire and wheel changing.

AIR-STD-11/8 - Lunette Eye Or Towing Ring

AIR-STD-11/9 - Cross-Servicing Adaptors

Pending effective standardization of aircraft servicing connectors, Nations agree to develop adaptors to allow their national servicing equipment to be used for servicing other Nations' aircraft in the interim period.

AIR-STD-12/1 - Electrical Power Supplies At Hardstandings

To tabulate Air Base Power Supplies at Hardstandings.

AIR-STD-12/10 - Aircraft Electrical Systems Characteristics

To standardize the essential characteristics of aircraft electrical power at the terminals of airborne equipment to which the power is supplied, and th limit the influence of the utilization equipment on the characteristics of the electrical power supplies.

AIR-STD-12/11 - Electrical Power Supplies At Hardstandings (Ch-1 5 Feb 1980)

To provide basic graphical symbols for aircraft electrical circuit diagrams to facilitate the reading and understanding of wiring diagrams by maintenance personnel of member countries.

AIR-STD-12/12 - Ground Electrical Power Supplies For Aircraft

AIR-STD-12/13 - Interchangeability Of Cable Splices (In Line Connectors) Tinned Copper

To provide a chart showing the degree of interchangeability of cable splices (in-line connectors) of United Kingdomand United States designs and their identification.

AIR-STD-12/14 - Multi-Contact Connectors (With Amendment 1)

AIR-STD-12/15 - Aircraft Storage Batteries (Issued Controlled)(No S/S Document)

To provide a standard for aircraft storage batteries for interchangeability between ASCC countries and for their identification.

AIR-STD-12/16 - Single Hole Toggle Switches Mounting Details

AIR-STD-12/17 - Precision High Melting Point Cartridge Fuse Used On Aircraft (With Amendment 1

AIR-STD-12/18 - Aircraft Storage Electric Plug (Issued Controlled)

To standardize the mating features and maximum envelope of aircraft storage battery electric plugs.

AIR-STD-12/19 - Electro Magnetic Compatibility Test Methods For Aircraft Electrical And Electronic Equipment

AIR-STD-12/2 - Aircraft Lamps

To ensure that all aircraft are provided with lamps of sufficient similarity so that the lighting systems of each country's aircraft can readily be serviced at airfields of participating countries.

AIR-STD-12/20 - Ground Recharging Of Aircraft Main Batteries

AIR-STD-12/22 - Electromagnetic Compatibility (Emc) Of Aircraft Systems

AIR-STD-12/23 - Electrical Safety Interconnections Between Aircraft, Support Equipment & Earth

AIR-STD-12/24 - Bonding And In-Flight Lightning Protection For Aircraft

AIR-STD-12/25 - Earthing/Grounding Plug & Socket

The object of this Air Standard is to standardize the essential dimensions for untermateability between earthing/grounding plugs and Nations.

AIR-STD-12/3 - Hand Operated Circuit Breakers

AIR-STD-12/4 - Interchangeability Of Tinned Copper Terminals (Lugs)

AIR-STD-12/5 - Electric Cables

To adopt as standard, ranges of aircraft electrical cables., interchangeable in: a. rating, b. conductor diameter, c. overall diameter.

AIR-STD-12/6 - Connectors For 28 Volt Dc Servicing Power (Change 1

AIR-STD-12/7 - Connectors For 115/200 Volt 400 Hz 3-Phase Ac Servicing Power (Change 2)

AIR-STD-12/9 - Circuit Identification (S/S By Air Std 104/19)

To adopt as a standard a common aircraft function letter to identify different types of electrical circuits in aircraft.

AIR-STD-14/10 - Liquid Nitrogen Characteristics

AIR-STD-14/11 - Cylinder Stored Compressed Breathing Air Characterisitics

AIR-STD-14/12 - Characteristics Of Supply Equipment For Liquid Nitrogen

AIR-STD-14/13 - Aircraft Gaseous Oxygen Replenishment Connection

AIR-STD-14/14 - Aircraft Gaseous Nitrogen Replenishment Connections

AIR-STD-14/15 - Aircraft Compressed Air Replenishment Connections

AIR-STD-14/16 - Characteristics Of Supply Equipment For Breathable Compressed Air (With Amendment 1)

AIR-STD-14/17 - Oil Free Compressed Nitrogen Characteristic, Supply Pressure And Hoses

AIR-STD-14/3 - Characteristics Of Supply Equipment For Liquid Oxygen

To standardize on the essential Mating Features of Ground Service Connector for Liquid Oxygen, Supply Pressure, and Hoses.

AIR-STD-14/4 - Working Pressures Of Liquid Oxygen Converters For Aircraft

To adopt as standard three working pressures for liquid oxygen convertors for aircraft as a first step towards full interchangeability of the convertors used by the ASCC Member Nations.

AIR-STD-14/6 - Oil Tolerant Compressed Nitrogen Characteristics Supply Pressure And Hoses

AIR-STD-14/7 - Compressed Air For Technical Purposes, Characteristics, Supply Pressure & Hoses

AIR-STD-14/8 - Adaptors For Ground Support Of Air Ventilated Swits

Pending effective standardization of connectors, to develop adaptors to permit Air Ventilated Suits of each nations aircrew to be connected to other Member Nations' Ground Air Supply Equipment.

AIR-STD-15 - Glossary Of Abbreviations Used In Nato Documents

AIR-STD-15/1 - Interchangeability Chart Of Standardized Aviation Fuels, Lubricants & Allied Products

AIR-STD-15/10 - Compressed Nitrogen Characteristics For Oil Tolerant Use (Including Supply Pressure And Hoses)

The purpose of this agreement is to ensure that each member nation can service other member nations' aircraft components and systems, other than oxygen and oxygen related with nitrogen of acceptable purity and at the required working pressure.

AIR-STD-15/11 - Oil Free Compressed Nitrogen Characteristics, (Including Supply Pressure And Hoses)

The purpose of this agreement is to standardize characteristics of compressed oil free nitrogen, its supply pressure and servicing hoses.

AIR-STD-15/12 - Liquid Nitrogen Characteristics

To standardize Liquid Nitrogen Characteristics.

AIR-STD-15/13 - Compressed Air Characteristics (Including Supply Pressure And Hoses)

To standardize compressed air characteristics, supply pressure and hoses.

AIR-STD-15/14 - Breathing Oxygen Characteristics (Including Supply Pressure And Hoses)

The purpose of this agreement is to ensure that each member nation can service aircraft of the other member nations with liquid or gaseous oxygen of acceptable purity for breathing and at the required working pressures.

AIR-STD-15/2 - Minimum Filtration Standards For Fuels, Lubricants And Allied Products Dispensed Into Aircraft(No S/S Document)

AIR-STD-15/3 - Petroleum Products, Minimum Quality Surveillance (With Change Notice 1)

The purpose of this agreement is to standardize the minimum quality surveillance measures for petroleum products for use by Navies, Armies and Air Forces of ASCC nations in peacetime and war.

AIR-STD-15/4 - Allowable Deterioration Limits For Fuels, Lubricants And Allied Products

The aim of this agreement is to standardize the allowable deterioration limits for fuels and lubricants used by ASCC Forces.

AIR-STD-15/5 - Guide Specification (Minimum Quality Standards) For Aviation Gasoline, Nato F-18

AIR-STD-15/6 - Guide Specification (Minimum Quality Standards) For Aviation Fuels: Nato F-34, F-35, F-40, And F-44

The purpose of this agreement is to provide a document (guide specification) which establishes the minimum quality standards of aviation turbine fuels used in service operations by the Navies, Armies and Air Forces of the ASCC nations.

AIR-STD-15/7 - Guide Specification For Petroleum Base (H-515,H-520 And C-635) And Polyalphaolefin Base (H-537, H-538 And H-544) Aviation Hydraulic Fluids

To provide a document (Guide Specification) which establishes the minimum quality standard for petroleum base (H-515, H-520 and C-635) and polyalphaolefin base (H-537, H-538 and H-544) aviation hydraulic fluids used by the Navies, Armies and Air Forces of the ASCC Nations.

AIR-STD-15/8 - Replenishment Of Engine Thrust Augmentation Systems

To identify the engine thrust augmentation fluid requirements of member nations' aircraft and to ensure that replenishment equipment is capable of meeting such requirements.

AIR-STD-15/9 - Interchangeability Chart Of Standardized Aviation Fuels, Lubricants And Allied Products

To record the degree of standardization or interchangeability of and to state the emergency substitutes for the Aerospace Fuels, Lubricants and Allied Products used by Air Forces, Navies and Armies of the ASCC nations.

AIR-STD-17/1 - Aircraft Jacking Pads (Ch 1 10 Sept 86) Request Other Than Dod Must Be Sent Via Hq Usaf/Xoxx(Iso) Wash, Dc 20330-5058

AIR-STD-17/11 - Diameters For Aircraft Gravity Filling Orifices

To lay down a minimum size of orifice for the gravity filling point of the tank or reservoir, relative to each fluid, so as to ensure that the orifice for any given fluid in any aircraft will accept the nozzle of the ground equipment used by the participating nations to relenish that fluid.

AIR-STD-17/12 - Angles Of Head For Countersunk Rivets

AIR-STD-17/14 - Method Of Dimensioning And Determining Clearance For Aircraft Tyres And Rims (With Amendment 1)

AIR-STD-17/15 - Screw Thread, Hexagon Sizes And Undercut Dimensions For P, Pe (Tube) Fitting (Inch Units)

AIR-STD-17/16 - Preferred Screw Threads For Size Below 1/4 Inch Diameter For Aeronautical Use (Ch-1 30 Nov 1977)

AIR-STD-17/18 - Dimensions Of Tapped Bosses And Holes For Fluid Connections

AIR-STD-17/19 - Profile Dimensions For V Band Coupling Flanges For Piping & Ducting

AIR-STD-17/2 - Hexagon Bolt Head & Nut Sizes (Change 1 - 30 Nov 77)

AIR-STD-17/20 - Pipe (Tube Connections For Aerospace Vehicle Instrument (Ch-3 23 May 1979)

AIR-STD-17/21 - Pipe Fitting Sealing Rings

AIR-STD-17/22 - Low Pressure Air & Associated Electrical Connections For Aero Engine Starting (S/S By Air Std 18/12)

AIR-STD-17/23 - Picketing Or Tiedown Fittings For Shipborne Aircraft (Including Helicopters)

To ensure that the picketing or tie-down fittings on shipborne aircraft (including Helicopters) will be accept the attachment hooks of each country's deck securing gear and to facilitate picketing of the shipborne aircraft.

AIR-STD-17/24 - Countersunk Screw Heads For Aeronautical Fasteners

AIR-STD-17/26 - Countersunk Rivets - Physical Requirements - Change 1 - 30 Nov 77

AIR-STD-17/27 - Range Of Sizes For Elastomeric (O) Rings For Aerospace Vehicle Purposes (Inch Series)

AIR-STD-17/28 - Dimensions Of Tapped Holes For Wire Thread Inserts (Ch-1 30 Nov 1977)

AIR-STD-17/29 - In-Flight (Aerial) Refuelling (S/S By Air-Std-25/13)

In order to facilitate in-flight refueling between aircraft of the participating nations.

AIR-STD-17/3 - Identification Of Pipe Lines And Electrical Conduits In Aircraft, Missile And Space Vehicle

AIR-STD-17/30 - Screwdriver Recesses

AIR-STD-17/31 - Pressure Replenishment Connections For Menthanol Water And Demineralized Water

To standardize the mating dimensions of the connections to be installed in aircraft for the pressure replenishment of methanol servicing of aircraft of the ASCC nations.

AIR-STD-17/32 - Pressure Replenishment Connection For High Test Peroxide

AIR-STD-17/33 - Air Supply & Test Connections

AIR-STD-17/34 - Replenishment Connection For Potable (Drinking) Water

To enable the ground equipment of one country to be connected to the aircraft of the other ASCC countries, thus obtaining a cross-servicing facility without the need for prepositioning ground equipment.

AIR-STD-17/35 - Statement Of Engine Performance In Model (Engine) Specifications

AIR-STD-17/36 - Turboprop And Turboshaft Engine Test Requirements

AIR-STD-17/37 - Ball, Roller & Needle Roller Bearings (Change 2 - 30 Nov 77)

AIR-STD-17/38 - Aircraft Cargo Tie Down Fittings

To standardize the dimensions of the mating features of cargo tie down rings or links to be provided on aircraft for securing cargo, which will permit the use of lashings of other member nations.

AIR-STD-17/39 - Dimensional Features For Stretcher (Litter) Support & Retention By The Handles (S/S By Air Std 44/56)

To standardize the dimensional aspects of stretcher (litter) support and retention by the handles, to permit of the carriage of stretchers (litters) of any one country by aircraft of the other member nations.

AIR-STD-17/4 - Fuel Nozzle Grounding Plug And Socket

AIR-STD-17/40 - Screw Threads With Controlled Radius Root (Ch-2 30 Nov 1977)

AIR-STD-17/41 - Preformed Flexible Steel Wire Rope For Use In Aircraft Control Systems

AIR-STD-17/42 - Rating Nomenclature For Turbojet And Turboprop Engines

AIR-STD-17/43 - Salt Water Corrosion Susceptibility Test Procedure

AIR-STD-17/44 - Sand Ingestion Tests On Turbine Engines

AIR-STD-17/45 - Contamination Limits For Engine Bleed Air

AIR-STD-17/46 - Helicopter External Cargo Hooks

AIR-STD-17/47 - Stiffnuts (Self Locking Nuts) (Ch-1 30 Nov 1977)

To establish for the purpose of cross-servicing an acceptable degree of dimensional and functional interchangeability between similar type nuts manufactured in any of the ASCC countries and approved by the Government of the country of manufacture for use in its military aerospace equipments.

AIR-STD-17/48 - Floor Rails And Mating Equipment Attachment Pins

To standardize such features of floor rails and attachment pins as are necessary to permit of interchangeability of seats, cargo fittings and other related gear between aircraft of the participating nations.

AIR-STD-17/49 - Common Wrenching Features For Cylindrical Nuts (With Amendment 1)

AIR-STD-17/50 - Liquid Spring Undercarriage Unit Oil Replenishment Connection

AIR-STD-17/51 - Plain Bearings Incorporating Polytetrafluoroethylene (Ptfe) Bearing Surfaces

AIR-STD-17/52 - Pressure Replenishment Connections For Engine Lubricating Oil

To standardize the types of connections to be used for the pressure replenishment of aerospace vehicles with engine lubricating oil and thus facilitate the cross-servicing of each member nation's aircraft.

AIR-STD-17/53 - Configuration And Limiting Dimensions Of Twelve Point Bolt And Nut Drives

AIR-STD-17/54 - Pin, Quick Release, Single & Double Acting (Inch Series) (Change No. 1- 23 May 79)

AIR-STD-17/55 - Tube (Pipe) Support Clamps

To standardize a range of tube (pipe) support clamps for cross-servicing of aircraft for temperatures up to 500 C (932F).

AIR-STD-17/56 - Water Glycol Pressure Replenishment Connection

AIR-STD-17/57 - Method For Rounding Off Numerical Values When Dimensioning Aerospace Standard Parts

AIR-STD-17/58 - Metal Chip Detectors (Housings)

To define standard physical features and environmental conditions for the mounting housing of metal chip detectors for use in aircraft engines, drives and gear boxes.

AIR-STD-17/59 - Wrenching Element, External Spline

AIR-STD-17/6 - Tire Valve Couplings

To standardize tire valve couplings and thus facilitate servicing of the aircraft of the ASCC nations.

AIR-STD-17/60 - Engine Controls, Remote Adjustment Of

To standardize those features of attachment provisions required to permit connection of remotely actuated aircraft engine control adjustment devices so as to ensure interchangeability of maintenance and support equipment between participating nations where the aircraft may operate.

AIR-STD-17/61 - Rules And Factors For Conversion Of Traditional Us And British Units To Systeme International (Si) Units Of Measurement

AIR-STD-17/62 - Pressure Fuelling Replenishment Connection

AIR-STD-17/7 - Aircraft Towing Attachments (S/S By Air-Std-25/9)

To standardize the form and essential dimensions of towing attachments for aircraft, to enable the member nations to handle each other's aircraft.

AIR-STD-17/8 - Grease Nipples (Inch Series)

AIR-STD-17/9 - Aircraft Emergency Towing Attachments (S/S By Air-Std-25/10)

AIR-STD-18 - Aircraft Propulsion Systems Wp 18

AIR-STD-18/1 - Statement Of Engine Performance In Model (Engine) Specifications

AIR-STD-18/10 - Tube (Pipe) Support Clamps

AIR-STD-18/11 - Hailstone Ingestion Tests For Gas Turbine Aero Engines (Rel To Other Than Dod Act Req Pri Appr Of Cnm, Mat 09B21, Wash, D.C. 20360)

AIR-STD-18/12 - Low Pressure Air & Associated Electrical Connections For Aero Engine Starting (Rel To Other Than Dod Act Req Pr Appr Of Cnm, Mat 09B21)

To standardize the mating dimensions of the nipple and associated electrical connection to be fitted to aircraft for the purpose of starting aircraft engines by low pressure air and thus facilitate cross-servicing of member nations aircraft.

AIR-STD-18/2 - Turboprop & Turboshaft Engine Test Requirements

AIR-STD-18/3 - Sand Ingestion Tests In Turbine Engines

AIR-STD-18/4 - Contamination Limits For Engine Bleed Air

AIR-STD-18/5 - Metal Chip Detectors (Housings)

AIR-STD-18/6 - Remote Adjustment Of Engine Controls

AIR-STD-18/7 - Contamination Limits For Fuel For Gas Turbine & Aero Engine Testing (Release To Other Than Dod Activities Requires Prior Approval Of Chief Of Naval Materiel Mat 09B21, Washington, D.C. 20360

AIR-STD-18/8 - Salt Water Corrosion Susceptibility Test Procedure (Release To Other Than Dod Activities Requires Prior Approval Of Chief Of Naval Materiel, Mat 09B21, Wash., Dc 20360

AIR-STD-18/9 - Pressure Replenishment Connections For Engine Lubricating Oil (Rel To Other Than Dod Act Req Pr Appr Of Cnm, Mat 09B21, Wash, D.C. 20360)

AIR-STD-19/1 - Joint Electronics Type Designator Systems

To ensure that each member nation utilizes the same type designation system.

AIR-STD-19/2 - Standard Airborne Electronic Data Transmission System

To promote interoperability and reduce proliferation of digital avionic subsystems in member nations by utilizing the same integration concept with standard digital signal interfaces.

AIR-STD-19/3 - Interoperability Of Aircraft Vhf Am And/Or Fm Multi-Frequency Transceiver Installations And Compatible Ground Radio Equipments

The intention of this agreement is to achieve interoperability. In order to enable participants more readily to be able to agree to the basic parameters necessary for interoperability, no attempt is made in this document to specify comprehensive equipment design standards.

AIR-STD-19/4 - Interoperability Of Aircraft Uhf Multi-Frequency Transceiver Installation & Compatible Ground Transmitters And Receivers

The intention of this agreement is to achieve UHF interoperabliity.

AIR-STD-19/6 - Avionics Life Cycle Cost Models And Techniques (Rel To Other Than Dod Act Req Pri Appr Of Hq Usaf/Xoxx-Iso, 20330-5058)

To exchange information on selected logistics models and techniques.

AIR-STD-20/10 - Ejector Release Units For Aircraft Stores

To provide a standard for design criteria for ejector release units for aircraft stores for interchangeability between ASCC nations.

AIR-STD-20/11 - Signals Underwater Sound

To provide a standard for military characteristics of Signal Underwater Sound to facilitate interchangeability.

AIR-STD-20/12 - Aircraft Store Ejector Cartridges

The purpose of this agreement is to standardize certain details of design of bomb ejection cartridges to facilitate interchangeable use of cartridges in cross-operations between aircraft of member nations.

AIR-STD-20/13 - Design Of Aircraft Stores

To standardize the structural and mechanical design of aircraft stores and their associated suspension equipment interfaces to facilitate interchangeability and the cross-servicing of aircraft.

AIR-STD-20/14 - Location Of Electrical Connectors For Aircraft Stores

To provide standard location of electrical connectors for aircraft stores to ensure interchangeable use between the ASCC countries.

AIR-STD-20/15 - Suspension Lugs For 1,000 Lb Class And 2,000 Lb Class Stores

To provide a standard for bail suspension lugs to ensure interchangeable suspension of airborne stores between ASCC Nations.

AIR-STD-20/16 - Design Guide To Preclude Hazards Of Electromagnetic Radiation To Airborne Weapon Systems

To standardize on a method of presenting test results used for the National Certification of aircraft electro-explosive sub-systems electromagnetic compatibility (EMC).

AIR-STD-20/17 - Mechanical Connectors Between Stores And Suspension Equipment For Arming And Associated Functions Of Stores

To standardize on the design and performance criteria of store arming components to facilitate interoperability.

AIR-STD-20/18 - Environmental Test Methods For Aircraft Stores Suspension And Release Equipment

The purpose of this agreement is to provide a standard for qualification testing of stores suspension equipment used in military aircraft of ASCC Nations.

AIR-STD-20/19 - Non-Eject Release Units For Aircraft Stores

To provide a standard for design criteria for non-eject release units for aircraft stores in order to promote interoperability between ASCC Nations.

AIR-STD-20/20 - Standardized Data List For Interoperability Studies And Certification Of Aircraft Stores

The purpose of this agreement is to provide standardized lists of the data required for participating nations to conduct interoperability studies of candidate non-nuclear, externally carried weapons on their aircraft, and the additional data required for certification or flight trials of these weapons on their aircraft. Nations should be aware that the data provided are for interoperability studies, and that there nay still be ground and/or flight trials required.

AIR-STD-20/21 - Airborne Stores Ground Fit And Compatibility Criteria

To provide a standardized set of criteria to define acceptable fit of aircraft stores on aircraft and a test method for determining the fit compatibility of the stores.

AIR-STD-20/22 - Aircraft Store Electrical Interconnection System

To provide a standard for electrical interconnection of stores and aircraft which will enchance interoperability between ASCC nations.

AIR-STD-20/23 - Safety Design Requirements For Airborne Dispenser Weapons

To standardize the safety design requirements for airborne dispenser weapons (dispenser and associated submunitions) both captive and free-flight. The agreement does not apply to chaff and flare dispenser systems.

AIR-STD-20/24 - 20Mm X 102 Ammunition For Aircraft Guns

The purpose of this agreement is to ensure interoperability among 20mm x 102 ammunition for aircraft guns.

AIR-STD-20/27 - Electrical Connector For Dispensers And Internal Intervalometer Type Rocket Launchers For Aircraft

The purpose of this agreement is to establish a common electrical interface for future dispensers and internal intervalometer type rocket launchers for aircraft.

AIR-STD-20/9 - Design Safety Principles For Aircraft Stores Fuzing

To standardize the design safety principles and general design criteria for fuzing systems, including safety and arming devices, to be employed in all aircraft weapon systems.

AIR-STD-25/1 - Pressure Replenishment Connections For Engine Lubricating Oil

AIR-STD-25/10 - Aircraft Emergency Towing Attachments (S/S By Air-Std-25/9)

To standardize the emergency towing attachments for aircraft, to enable the member nations' air forces to handle each other's aircraft.

AIR-STD-25/11 - Diameters For Aircraft Gravity Filling Orifices

The purpose of this agreement is to establish a minimum size of orifice for the gravity filling point of a tank or reservoir, for any given fluid used in aircraft. This will ensure that the orifice (for any given fluid in any aircraft) will accept the nozzle of the ground equipment used by participating nations to replenish that fluid.

AIR-STD-25/12 - Picketing Or Tiedown Fittings For Shipborne Aircraft (Including Helicopters)

The purpose of this agreement is to ensure that the picketing or tie-down fittings on shipborne aircraft (including helicopters) will accept the attachment hooks of each country??s deck securing gear and to facilitate picketing of the shipborne aircraft (including helicopters) of one country on the ships of the others.

AIR-STD-25/13 - In Flight (Aerial) Refuelling Equipment, Dimensions And Functional Characteristics

The purpose of this agreement is to facilitate in-flight refuelling between aircraft of the participating nations.

AIR-STD-25/14 - Pressure Replenishment Connections For Methanol Water & Demineralized Water (Release To Other Than Dod Refer To Hq Usaf/Xoxx(Iso) Wash, Dc 20330-5058

To standardize the mating dimensions of the connections to be installed in aircraft for the pressure replenishment of methanol water and demineralized water systems and thus facilitate cross-servicing of aircraft of the ASOC nations.

AIR-STD-25/15 - Air Supply And Test Connections

To standardize the types of connections, or themating features of connections, to be provided on aircraft for the intake of air from external sources on the ground, for air conditioning and for the testing of aircraft air systems and thus facilitate the cross-servicing of aircraft of member nations.

AIR-STD-25/16 - Replenishment Connection For Potable

AIR-STD-25/17 - Pressure Fuelling Replenishment Connection

The aim of this agreement is to standardize the pressure fuelling connections used in aircraft.

AIR-STD-25/18 - Connectors For 28 Volt Dc Servicing Power

To standardize the external DC Servicing Power Connections to the aircraft so that the external power supplies can be used to furnish electric power to the aircraft of any participating country.

AIR-STD-25/19 - Connectors For 115/200 Volt 400Hz 3-Phase Ac Servicing Power

The purpose of this agreement is to standardize the external AC servicing power connections to the aircraft so that the external power supplies of any participant can be used to furnish electric power to the aircraft of any participating country.

AIR-STD-25/2 - Low Pressure Air And Associated Electrical Connections For Aero Engine Starting

AIR-STD-25/20 - Aircraft Electrical Systems Characteristics,

To standardize the essential characteristics of aircraft electrical power at the terminals of airborne equipment to which the power is supplied, and to limit the influence of the utilization equipment on the characteristics of the electrical power supplies.

AIR-STD-25/21 - Ground Electrical Power Supplies For Aircraft

To provide common standards for ground source of electrical power for servicing of operational aircraft.

AIR-STD-25/24 - Ground Recharging Of Aircraft Main Batteries

To standardize the ground procedures for recharging aircraft main batteries to facilitate cross-servicing.

AIR-STD-25/25 - Electrical Safety Interconnections Between Aircraft, Support Equipment And Earth

To ensure that each member nation can interconnect aircraft and support equipment of other nations to ensure safety to life and equipment.

AIR-STD-25/26 - Earthing/Grounding Plug And Socket

The object of the Air Standard is to standardize the essential dimensions for interconnections between earthing/grounding plugs and sockets (receptacles to facilitate cross-servicing of aircraft of the Member Nations. These plugs and sockets (receptacles) are used for earthing/grounding of aircraft, fuel nozzles, and other purposes.

AIR-STD-25/27 - Aircraft Liquid Oxygen Replenishment Connections

To standardize on the essential Mating Features of Ground Service Connectors for Liquid Oxygen, Supply Pressure and Hoses.

AIR-STD-25/28 - Compressed Nitrogen Characteristics, Supply, Pressure & Hoses For Oil Tolerant Use

To ensure that each member nation can service aircraft of the other member nations with nitrogen of acceptable purity for other than oxygen systems and at the required working pressure.

AIR-STD-25/29 - Compressed Air, Characteristics, Supply, Pressure & Hoses For Technical Purposes

To standardize compressed air characteristics, supply pressure and hoses.

AIR-STD-25/3 - Aircraft Servicing, Hazard, And Emergency Markings

To identify and standardize servicing, hazard, and emergency markings inside and outside aircraft used by member nations.

AIR-STD-25/30 - Breathing Oxygen Characteristics, Supply Pressure And Hoses

To ensure that each member nation can service aircraft of the other member nations with liquid or gaseous oxygen of acceptable purity for breathing and at the required working pressures.

AIR-STD-25/31 - Liquid Nitrogen Characteristics

To standardize Liquid Nitrogen Characteristics.

AIR-STD-25/32 - Cylinder Stored Compressed Air For Breathing Purposes (Req To Other Than Dod Act Req Pri Appr Of Hq Usaf/Xoxx-Iso Wash, Dc 20330-5058) (No S/S/Document)

To standardize characteristics of cylinder stored compressed breathing air.

AIR-STD-25/33 - Characteristics Of Supply Equipment For Liquid Nitrogen

To standardize on the essential mating feature of the aircraft external charging connector for liquid nitrogen, supply pressure and hoses.

AIR-STD-25/34 - Aircraft Gaseous Oxygen Replenishment Connections

To establish the mating features of connections currently used on member nations aircraft for the replenishment of gaseous oxygen systems, including walk-around and bail-out bottles. In order that cross-servicing requirements can be determined. Further, to standardize high pressure oxygen connections used on future aircraft.

AIR-STD-25/35 - Aircraft Gaseous Air/Nitrogen Replenishment Connections

The purpose of this agreement is to standardize on the mating and access clearance dimension of gaseous and non-breathable air replenishment connections for member nations?? aircraft.

AIR-STD-25/36 - Aircraft Compressed Air Replenishment Connections

To establish the mating features of connections currently used on member nations' operational aircraft for the replenishment of compressed air systems, in order that cross-servicing requirements can be determined.

AIR-STD-25/37 - Oil Free Compressed Nitrogen Characteristics, Supply Pressure & Hoses

To standardize characteristics of compressed oil free ntirogen, supply pressure and hoses.

AIR-STD-25/4 - Aircraft Fuelling

To establish standard for fuelling aircraft.

AIR-STD-25/5 - Lunette Eye Or Towing Ring

To standardize the dimensions of the Lunette Eye or Towing Ring for use on drawbars, which are installed on mobile aircraft ground handling equipment, including aircraft tow bar to vehicle connections, to ensure that the vehicles of one member nation can be employed, safely and efficiently, for the movement of aircraft and ground support equipment of the other member nations.

AIR-STD-25/6 - Aircraft Hydraulic System Servicing

To identify the basic requirement for hydraulic systems replenishment and activation to facilitate the cross-servicing of each member Nation's aircraft.

AIR-STD-25/9 - Aircraft Towing Attachments

The purpose of this agreement is to standardize the form and essential dimensions of towing attachment points on aircraft for normal towing, as well as for those alternative methods of towing that use a tow bar or tow line.

AIR-STD-30/3 - Physical Interchange Of Digital Data

The purpose of this agreement is to ensure Member Nations can physically exchange digital form of engineering, maintenance and logistics data.

AIR-STD-30/5 - Interchange Of Digital Textual Data

AIR-STD-30/6 - Interchange Of Digital Raster Graphics

AIR-STD-30/7 - Interchange Of Digital Illustration Data

AIR-STD-44/10 - Data For Planning Air Movements

To standardize on the forms utilized in the planning and movements of troops and equipment in combined air transport operations.

AIR-STD-44/11 - Procedures For Coding, Tracing And Disposing Of Baggage

To adopt a standard of uniform coding of baggage items, to adopt a procedure for tracing missing baggage and to adopt a procedure for disposing of found baggage.

AIR-STD-44/12 - Restaint Factors For Fixed Wing Aircraft

To adopt as standard, factors for the restraint of air transported cargo and equipment in fixed wing transport (cargo) aircraft.

AIR-STD-44/13 - Drop Extraction Zones Visual Markings

AIR-STD-44/14 - Recovery And Release Of Parachutists Towed Behind Transport Aircraft

The purpose of this agreement is to standardize on procedure to release or retrieve parachutists towed behind transport aircraft.

AIR-STD-44/15 - Parachute Extraction Systems

To standardize parachute extraction assemblies and aircraft extraction parachute ejector installations so as to facilitate interchangeability of parachute extraction assemblies in aircraft of ASCC nations. It is not the purpose of this standard to provide for interchangeability of component parts of these parachute extraction assemblies.

AIR-STD-44/16 - Exchange Of Information - Transport Aircraft Loading Data

To authorize and establish procedures for exchange of transport aircraft load planning data.

AIR-STD-44/17 - Fixed Wing Cargo Aircraft Tie-Down Fittings

To adopt as standard the strength, dimensions and location of cargo floor tie-down fittings in fixed wing transport aircraft.

AIR-STD-44/18 - Responsibilities Of Air Transport Units, And Air Transported (User) Units For Air Movement In Combined Operations

The purpose of this agreement is to adopt a standard policy for the division of air movement responsibilities between air transporting units and air transported (user) units in combined air transport operations.

AIR-STD-44/20 - Parachute Coupling Systems

AIR-STD-44/21 - Criteria For The Design Of Equip Required To Be Air Transported Orairdropped From Fixed Wing & Rotary Wing Transport Aircraft

To establish criteria for the design of equipment required to be air transported or air dropped from fixed wing and rotary wing transport aircraft and to ensure that national staffs consider these criteria in the design of aircraft.

AIR-STD-44/22 - Ground Handling Capabilities For Transport Aircraft (Exchange Of Information)

The object of this agreement is to adopt standard policies and procedures for the identification and control of aircraft pallets and associated restraint equipment contributed by participating nations for use during Combined Airlift Operations.

AIR-STD-44/23 - Division Of Responsibility Between Ground & Air Forces On Drop/Extraction Zones In Tactical Operations

To define the responsibility of the Airborne Force/Ground Force Commander and the Air Transport Force Commander with regard to the selection and marking of Drop/Extraction Zones.

AIR-STD-44/24 - General Rules Covering The Transport Of Loads By Helicopter

The purpose of this agreement is to define responsibilities and adopt standard helicopter cargo carrying procedures.

AIR-STD-44/25 - Transport Of Troops Byhelicopter

To adopt standard helicopter troop transport procedures.

AIR-STD-44/26 - Ultra Low Level Airdrop System Using Parachute Extraction

The purpose of this agreement is to establish parameters and methods for the ultra low level airdrop from transport aircraft, using parachute extraction, of stores and equipments loaded on the platform/skidboards.

AIR-STD-44/27 - Airdrop Of Door Bundles With Sticks Of Parachutists

To adopt as standard a procedure for the airdrop of door bundles with sticks of parachutists.

AIR-STD-44/28 - Colours For The Identification Of Airdropped Supplies

To standardize a range of colours to be displaued on the outside surface of airdropped supplies, in order to enable their contents to be identified by ASCC forces, with minimum of delay.

AIR-STD-44/29 - Ready Access In Fixed Wing Transport Aircraft

To specify limits which will permit the passage of personnel past a load that has been lashed/restrained in a fixed wing transport aircraft.

AIR-STD-44/3 - Lashings For Fixed Wing Aircraft

The purpose of this agreement is to adopt a standard strength range of lasings which will permit the lashings of any one of the ASCC countries to be used in the fixed wing aircraft of the other Nations.

AIR-STD-44/30 - Responsibility For The Design And Provision Of Adaptors Necessary To Achieve Compatibility Of Air Cargo Handling Equipment (With Amendment 1)

AIR-STD-44/31 - Tactical Refuelling Of Helicopters In Air Transport Operations

To standardize refuelling procedures for rotary wing aircraft in a tactical enviroment.

AIR-STD-44/32 - Technical Criteria For The Transport Of Cargo By Helicopter

To establish design criteria for the internal and external load equipment for air transport by helicopter and to ensure that national staffs consider these criteria in future design.

AIR-STD-44/33 - Helicopter Tactical Or Non-Permanent Landing Sites

To adopt standard dimensions and marking for helicopter landing sites for day and night operations.

AIR-STD-44/34 - Tactical Formation Flying By Helicopters In Air Transport Operations

The purpose of this agreement is to standardize procedures for day and night tactical helicopter formation flying.

AIR-STD-44/35 - Drop Zones And Extraction Zones: Criteria, Markings And Information Check Lists

To define the factors that require consideration when selecting and assessing the capacity of drop zones and to adopt a standard drop zone and extraction zone information checklists.

AIR-STD-44/36 - Aeromedical Evacuation By Helicopter

The purpose of this agreement is to standardize the procedures used in aeromedical evacuation by helicopter.

AIR-STD-44/37 - Criteria For Selection And Marking Of Landing Zones For Fixed Wing Aircraft

To adopt standard criteria for selection and marking of Landing Zones (LZ) for fixed-wing aircraft in tactical air transport operations, but excluding Landing Zones used for Special Forces operations.

AIR-STD-44/38 - Wartime Air Movement Priorities System

The purose of this agreement is to provide a priority system to facilitate and assure the timely movement of airlift traffic within ASCC member nations.

AIR-STD-44/39 - Design Criteria For The 10,000 Lb (4,545 Kg) Air Transport Pallet

The purpose of this agreement is to establish design criteria for the 10,000 lb (4,545 Kg) air transport pallet.

AIR-STD-44/40 - Performance Criteria For Honeycomb Paper Used As Energy Dissipating Material

To adopt standard criteria to which honeycomb paper used as Energy Dissipating Material (EDM) must perform when used for aerial delivery tasks.

AIR-STD-44/41 - Combined Air Terminal Operations

To object of this agreement is to adopt the policy and procedures for the operation of a Combined Air Terminal.

AIR-STD-44/42 - Marshalling Signals For Fixed Wing & Rotary Wing Aircraft

To standardize marshalling signals for fixed wing and rotary wing aircraft by day and night.

AIR-STD-44/43 - Air Transport Baggage Tags

The purpose of this agreement is to standardize the basic form and minimum data elements of baggage tags when such tags are used by participating nations to identify baggage of personnel travelling via military air transport.

AIR-STD-44/44 - Helicopter External Cargo Hook Dimensions (Ch-1 2 Oct 1978)

AIR-STD-44/45 - Procedures For Tracing Air Baggage And Missing Air Cargo

To adopt a standardized procedure to trace lost or found air baggage, provide uniform descriptions of lost/found baggage, report air cargo delivery discrepancies, and to dispose of unclaimed baggage.

AIR-STD-44/46 - Load Preparation For External Carriage By Helicopters

AIR-STD-44/47 - Identification And Control Of Aircraft Pallets And Associated Restraint Equipment During Combined Airlift Operations (Sc-M)

AIR-STD-44/48 - Ground Security Procedures Against Hijacking Of Air Transport Aircraft

The aim of this agreement is to define the ground security procedures against hijacking of air transport aircraft of the ASCC nations while involved in combined airlift operations. The ground security policies and procedures of the member nations will apply when transport aircraft are operated on behalf of that nation's unilateral missions.

AIR-STD-44/49 - Movement, Handling And In Transit Storage Of Cargo Requiring Temperature Controlled Conditions

The purpose of the agreement is to standardize procedures for the air movement and in-transit storage of special cargo requiring controlled temperature conditions.

AIR-STD-44/50 - Emplaning And Deplaning At The High Hover

The purpose of this agreement is to standardize methods and procedures to be adopted when troops and cargo are to be inserted or extracted by helicopter at the high hover.

AIR-STD-44/52 - Transportation Of Troops On Aircraft Transporting Hazardous Cargo

The aim of this agreement is to define the conditions under which troops and hazardous cargo can be airlifted by military/military controlled aircraft under tactical, contingency, wartime or emergency conditions.

AIR-STD-44/53 - Operational Carriage By Helicopter Of Ammunition & Fuel

To define responsibilities and adopt standard procedures for the Operational Carriage by Helicopter of Ammunition and Fuel.

AIR-STD-44/56 - Dimensional Features For Stretcher (Litter) Support & Retention By The Handles

To standardize the dimensional aspects of stretcher (litter) support and retention by the handles, to permit of the carriage of stretchers (litters) of and any one country by aircraft of the other member nations.

AIR-STD-44/58 - Planning Procedures For Tactical Air Transport Operations

The purpose of this agreement is to define the factors that require consideration when selecting and assessing the capacity of landing zones, drop zones and extraction zone information checklists.

AIR-STD-44/59 - Floor Rails & Mating Equipment Attachment Pins

To standardize such features of floor rails and attchment pins as are necessary to permit of interchangeability of seats, cargo fittings and other related gear between aircraft of the participating nations.

AIR-STD-44/60 - Cross Servicing Of Helicopters Engaged In Land Operations

The object of this agreement is to adopt standard procedures for cross-servicing of helicopters in multi-national land operations.

AIR-STD-44/62 - The Use Of Horse Collar (Strop) Type Helicopter Hosting Gear

AIR-STD-44/64 - Location Aids For Survivors Of Aircraft Accidents

The purpose of this agreement is to define the type and characteristics of aids to assist in the location of survivors or aircraft accidents.

AIR-STD-44/8 - System For Tracing Missing Cargo

To adopt a standard method of tracing missing cargo and correcting load discrepancies in the transportation of air cargo that will ensure delivery of cargo to consignee.

AIR-STD-44/9 - Handling And Documentation Of Dangerous Cargo For Air Transportation

To bring about increased standardization of procedures for the classification, labelling, marking, certification and documentation of dangerous cargo for movement on military aircraft.

AIR-STD-45/3 - Joint Air Operations Doctrine

To standardize the principles and planning considerations concerned in the employment of air power in tactical air operations.

AIR-STD-45/4 - Counter Air Operations

To standardize the tactical procedures to be used in the planning and execution of Counter Air Operations.

AIR-STD-45/5 - Tactical Air Procedures Offensive Air Support Operations

To standardize the tactical procedures to be used in the planning and execution of Offensive Air Support Operations.

AIR-STD-45/6 - Airspace Control In Times Of Crisis And War

To standardize the tactical procedures to be used in the planning and execution of Airspace Control in times of crisis and war.

AIR-STD-45/7 - Tactical Air Procedures Air Interdiction Operations

To standardize the tactical procedures to be used in the planning and execution of Interdiction Operations.

AIR-STD-45/8 - Tactical Air Procedures Tactical Air Support Of Amphibious Operations

To standardize the command and control procedures to be used by tactical air supporting amphibious operations.

AIR-STD-50/10 - Analogue Video Standard For Aircraft System Applications

To standardize on analogue video formats used in aircraft systems.

AIR-STD-50/2 - Digital Time Division Command/Response Multiplex Data Bus

AIR-STD-50/23 - Generic Open Architecture (Goa) Framework Standard

To achieve easier development, improved maintenance, and a decrease in life cycle costs of avionics systems by using the Society of Automotive Engineers AS 4893, Generic Open Architecture (GOA) Framework Standard, for those applications dictated by systems requirements.

AIR-STD-50/3 - Sixteen Bit Computer Instruction Set Architecture - Chg. 1 Dtd 25 Fef 86 ( Req For Issue Other Than Dod Must Be Sent Via Hq Usaf/X/Xx (Iso) Wash Dc 20330-5058

To promote interoperability and reduce proliferation of software-incompatible processors in member nations by utilizing the same sixteen-bit instruction set architecture.

AIR-STD-50/5 - Standardization Of A Real Time High Order Computer Programming Language For Avionics Systems Application (Rel To Other Than Dod Act Req Pri Appr Of Hq Usaf/Xoxx, Wash Dc 20330-5058)

AIR-STD-50/7 - Discrete Signal Interfaces (Rel To Other Than Dod Act Req Pri Appr Of Hq Usaf/Xoxx, Wash Dc 20330-5058)

AIR-STD-51/1 - Helicopter Hoisting Gear, The Use Of Horse Collar (Strop) Type

To adopt a standard for a horse collor (rescue strap) type hoisting gear in order that all nations will be familiar with surivor pick-up equipment employed in rescue operations.

AIR-STD-51/12 - Characteristics Of Emergency Personnel Parachutes (Rel To Other Than Dod Act Req Pri Appr Of Hq Usaf/Xoxx(Iso), Wash Dc 20330-5058)

AIR-STD-51/2 - Emergency Markings

To standardize those markings inside and outside aircraft of member nations which: (a) Faciliate escape action in emergency. (b) Denote position of equipment for use in an emergency. (c) Give warnings to would-be rescuers, neglect of which may cause them injury.

AIR-STD-51/3 - Search Pattern, Personal Locator Beacons

To standardize the flight patterns of search aircraft when searching for survivors known or believed to be equipped with UHF and /or VHF personal locator beacons, in order that a search may be mounted using search aircraft of one or more member nations and may be co-ordinated by a Rescue Co-ordination Centre (RCC) of any member nation.

AIR-STD-51/4 - Standard Search Planning Data

AIR-STD-51/5 - Beacons, Personal Locator, General Characteristics Of

To incorporate in Personal Locator Beacons such common characteristics as will ensure their compatibility with the radio search equipment of member nations.

AIR-STD-51/6 - Characteristics Of Emergency Personnel Parachutes

To standardize the colour scheme of canopies of emergency personnel parachutes in order to facilitate location, identification and recovery of survivors by rescue forces of member nations.

AIR-STD-51/7 - Location Aids For Survivors Of Aircraft Accidents

AIR-STD-52/1 - Format Sizes For Air Cameras (Framing)

To adopt a standard range of air camera format sizes to permit the common use by all forces of air roll films, and processing, printing and other supporting equipments.

AIR-STD-52/10 - Sheet Photographic Paper For Air Photography

AIR-STD-52/11 - Dimensions, Tolerances, Characteristics And Core Sizes Rolled Photographic Paper For Air Photography

AIR-STD-52/13 - Calibration Certificate For Mapping Cameras

To establish a standard mapping calibration or performance certificate to facilitate maximum use of interchanged ASCC mapping photography by assuring the availability of essential metric data.

AIR-STD-52/14 - Dimensions, Tolerances And Characteristics Of 70Mm, 126Mm And 240Mm Rolled Film For Air Photography

AIR-STD-52/15 - Cores For 70 Mm Air Film

AIR-STD-52/16 - The Range Of Design Criteria And Functional Parameters For Low Altitude Photoflash Cartridges (To Be Reissued As Ascc Air Std 20/18)

AIR-STD-52/17 - Spools For 70 Mm, 126 Mm, And 240 Mm Rolled Air Film

AIR-STD-52/18 - Spacing Of 57 X 57Mm Exposures On 70Mm Perforated Film

AIR-STD-52/19 - Reconnaissance System Cross Servicing Information

AIR-STD-52/20 - Essential Data For Film Processing And Reconnaissance System Turn-Around

AIR-STD-52/21 - Target Pattern For Determination Of Aerial Photographic Resolution

AIR-STD-52/3 - Method Of Marking Pre-Packed Processing Chemicals For Black And White Negative And Positive (Air) Photographic Materials

AIR-STD-52/4 - Focal Lengths Of Lenses For Air Reconnaissance And Mapping Cameras

AIR-STD-52/5 - Black & White Air Film Developer High Contrast (Change 2 - 12 Jun 78)

AIR-STD-52/6 - Dimensions, Tolerances & Characteristics Of 16Mm & 35Mm Rolled Film For Aerial Cameras (Rel To Other Than Dod Act Req Pai Appr Of Hq Usaf/Xoxx (Iso) Wash, Dc 20330-5028)

To adopt standard dimensions, tolerances and characteristics for 16 and 35mm rolled film for airborne cameras, to permit the common use of film, in processing equipment, printing equipment, and other supporting equipments.

AIR-STD-52/7 - Method Of Determining The Principal Sensitometric Characteristics Of Black And White Rolled Air Film

AIR-STD-53/1 - The Air Almanac

AIR-STD-53/10 - Standard Analogue Heading Outputs

AIR-STD-53/11 - The Specification For Evaluation Of The Accuracy Of Inertial Navigation Systems (Rel To Other Than Dod Act Req Pri Appr Of Hq Usaf/Xoxx(Iso), Wash Dc 20330-5058)

To adopt a standard method of determining the position accuracies of pure Intertial Navigation Systems.

AIR-STD-53/12 - The Specification And Evaluation Of The Accuracy Of Airborne Doppler Ground Velocity Sensors

To adopt a standard method of determining the accuracies of Airborne Doppler Ground Velocity Sensors.

AIR-STD-53/13 - The Specification For Evaluation Of The Accuracy Of Airborne Doppler Navigation Systems

AIR-STD-53/14 - Definition Of Sea State For Use In Connection With Doppler Navigation

AIR-STD-53/16 - The Specification For Evaluation Of The Accuracy Of Hybird Navigation Systems (Rel To Other Than Dod Act Req Pr Appr Of Cnm, Mat 09B21, Wash,D.C. 20360

AIR-STD-53/18 - Microwave Landing Systems (Mls) ( Relto Other Than Dod Act Req Pri Appr Of Hq Usaf/Xoxx(Iso), Wash Dc 20330-5058)

AIR-STD-53/2 - Sight Reduction Tables

To adopt standard celestial Sight Reduction Tables for Air Navigation.

AIR-STD-53/3 - The Proper Names Of 68 Stars

To adopt as standard the proper names of 68 stars used for air navigation.

AIR-STD-53/4 - Type Ms-28012-B6A Driftmeter

AIR-STD-53/5 - Minimum Operational Requirement (Mc) For Lightweight Doppler Systems For Fixed Wing Aircraft

AIR-STD-53/6 - True Airspeed Outputs

To adopt as standard, factors for True Airspeed Outputs.

AIR-STD-53/7 - Data Transmission For Radar Doppler Systems

To establish data transmission criteria for use in doppler radar systems.

AIR-STD-53/9 - Lightweight Doppler Navigation Equipment For Helicopters

AIR-STD-61/1 - Ejection Acceleration Limits

To establish guidelines to be used to assess the injury potential from acceleration imposed upon an aircraft crew member during powered emergency escape from a disabled aircraft.

AIR-STD-61/11 - Methodology For Cockpit Thermal Assessments

AIR-STD-61/12 - Methodology For Evaluation Of Anti Exposure Clothing In Cold Water Using Human Subjects (Issued Controlled)

To agree on a methodology for the evaluation of anti-exposure clothing in cold water immersion using human subjects so that data collected by the various member countries may be used without replication of experiments.

AIR-STD-61/13 - Measurement Of Sound Attenuation Of Hearing Protective Equipment

To define methods of measuring the sound attenuation of hearing protective equipment.

AIR-STD-61/14 - The Measurement Of Protection Provided To The Respiratory Tract And Eyes Against Nbc Agents In Particulate, Aerosol And Vapor Form

To define a standard procedure for measuring the protection afforded to the respiratory tract and eyes by aircrew equipment assemplies againist Nuclear, Biological and Chemical Warfare agents in particulate, aerosol and vapor form.

AIR-STD-61/15 - Anthropometric Criteria For Litters Standards

AIR-STD-61/16 - Aviation Medicine/Physiological Training Of Aircrew

To define the minium requirements for initial and periodic aviation medicine/physiological training that shall be given to aircrew.

AIR-STD-61/2 - Restraint And Parachute Harnesses For Aircrew (S/S By Air-Std-61/102/2)

AIR-STD-61/20 - Method Of Partial Pressure Suit Evaluation For High Altitude Protection

To establish guidance as to the methods to be used for the evaluation of partial pressure assemblies to be worn by aircrew operation pressurized aircraft at altitudes above 50,000 feet (15,000m).

AIR-STD-61/21 - Physiological Requirements For Aircrew Oxygen Masks For Use At High Breathing Pressures

To define the phsiological requirements to be met by oronasal masks which are to be used as part of oxygen delivery systems in high performance aircraft where pressure breathing at pressures greater than 4.0 kPa (30 mm Hq) may be required.

AIR-STD-61/22 - The Minimum Physiological Design Requirements For Aircrew Breathing Systems

To define the minimum physiological requirements to be met by aircraft systems which deliver oxygen and/or air oxygen mixtures to the respiratory tracts of aircrew in order to protect them againist hypoxia and contamination of the crew compartment atmosphere by toxic materials (excluding chemical warfare agents).

AIR-STD-61/23 - Minimum Physiological Requirements For Aircrew Nbc Protective Headgear

To define the physiological requirements for aircrew NBC headgear assemblies which are designated to provide a protection factor which does not fall below 10. (See definition at para 8c).

AIR-STD-61/24 - Filter Blower Performance For Aircrew Nbc Headgear

To define the performance requirements to be met by blown filtered air supplied for positively ventilated aircrew NBC protective headgear.

AIR-STD-61/3 - Escape System Test Methods

This standard prescribes the principles and methods for yesys to be used to demostrate the performance of an escape system for a specific aircraft.

AIR-STD-61/32 - Interchangeability Of Aircrew Medical Categories

To establish the medical procedures for the exchange and assignment of aircrew among nations.

AIR-STD-61/33 - Evaluation Procedures For Flight Helmets

AIR-STD-61/39 - Maximum Permissble Temperatures Of Materials For Safe Contact With Bare Skin

The object is to establish a method for: (2) predicting the maximum permissible temperature of any cockpit material for non-injurious contact with the bare skin; and (b) selection of appropriate materials and/or coating to provide thermally safe cockpit interiors to prevent injury and possible loss of operational control due to unexpected instantaneous pain or burn on contact.

AIR-STD-61/4 - Flotation And Sea Survival, Test Methods And Requirements

To standardize the requirements for inflatable life preservers.

AIR-STD-61/40 - A Technical Basis For Specifying The Insulation Of Immersion Protective Clothing

To standardize the technical basis upon which national guidelines to commanders may be drawn up in respect of the insulation requirements of immersion protective clothing.

AIR-STD-61/41 - Procedures For Calibration Of In-Flight Respiratory Data Acquisition Equipment

To define the procedures to be adopted for the calibration of equipment used in the acquisition of in-flight respiratory data.

AIR-STD-61/45 - Aviation Medicine/Physiological Training Of High Altitude Parachutists

To define the minimum aviation medicine/physiological training for high altitude parachutists.

AIR-STD-61/48 - Single Number Noise Reduction Of Hearing Protectors

The object of this AIR STD is to establish a method for calculating a single number moise reduction value to describe the overall performance of hearing protectors.

AIR-STD-61/5 - Escape Path Clearance In Ejection Seat Aircraft

AIR-STD-61/6 - Collection Of Data For Evaluation Of Helmets Damaged In Service (S/S By Air-Std-61/102)

To standardize the data collected from helmets damaged in service.

AIR-STD-61/7 - Minimal Protection For Aircrew Exposed To Altitudes Above 50,000 Feet

To establish guidance as to the minimum acceptable protection for aircrew members operating pressurized aircraft at altitudes above 50,000 feet, or exposed to cockpit/cabin altitudes in excess of 25,000 feet.

AIR-STD-61/73 - Minimum Standards For Breathing Equipment For Parachutists Between 13,000 & 25,000 Feet Pressure Altitude

AIR-STD-61/79 - Terminology Of Aeromedical Evacuation

AIR-STD-61/8 - Criteria For Reporting The Nature Of Clothing Materials On Assemblies Subjected To Physical & Operational Testing

AIR-STD-61/80 - Documentation Of Aeromedical Evacuation

AIR-STD-61/81 - Tests For Protective Capacity Of Fire Resistant Clothing Materials

AIR-STD-61/82 - Instrumentation For Escape System Thermal Hazard Analysis

AIR-STD-61/83 - A Basis For Common Practices And Goals In The Conduct Of Anthropometric Surveys

AIR-STD-61/84 - Initial Investigation And Immediate Management Of Laser Eye Injury In Aircrew

AIR-STD-61/9 - Protection Of Personnel Against The Effects Of High Levels Of Sound Upon Hearing & Operational Efficiency

AIR-STD-64/11 - Delineation Of Air Defense Identification Zones On Aeronautical Charts And Flight Information Publications

To ensure that Air Defense Identification Zones (ADIZ), when shown, are delineat4ed in the same manner on all aeronautical charts and Flight Information Publications.

AIR-STD-64/12 - Delineation Of The International Date Line On Aeronautical Charts And Flight Information Publications

To ensure that the placement of the International Date Line is the same on all aeronautical charts and Flight Information Publications.

AIR-STD-64/15 - Flight Information Publication, Enroute

To promote the standardization of Enroute Flight Information Publications produced by member nations to facilitate their use by any of the participating air forces.

AIR-STD-64/16 - Flight Information Publications - Planning

To identify the operational requirement for Flight Information Publication (FLIP), Planning Documents and to promote the standardization of such products published by member ASCC nations to facilitate use by any of the participating air forces.

AIR-STD-64/18 - Title For Flight Information Publications

To standardize titles for Flight Information Publications (FLIP).

AIR-STD-64/19 - Explanatory Information Required On Aeronautical Charts

To identify the explanatory information to be shown on seronautical charts to satisfy the combined operational requirements of the member air force.

AIR-STD-64/20 - Operational Usage Criteria (S/S By Adv Pub 64/39)

AIR-STD-64/21 - Abbreviations And Code Legend Flight Information Publications 141166

To enable participating air forces by adoption of a common directory of abbreviations and codes to understand and use, without special instructions, the series of Flight Information Publications produced by any one of the air forces.

AIR-STD-64/23 - Identification Of Scale On Aeronautical Charts

To enable participating air forces, by adoption of a common method, to identify without special instructions the scale of any aeronautical chart produced by any one of the air forces.

AIR-STD-64/24 - Symbols For Aeronautical Charts

To standardize the symbols used on aeronautical charts in order that air forces of one country may more easily use the aeronautical charts produced by participating nations.

AIR-STD-64/25 - Minium Content And Colour Of Aeronautical Information For Aeronautical Charts

To standardize requirements for the colour and minimum aeronautical information content on aeronautical charts so that member air forces may more easily use the charts produced by participating nations.

AIR-STD-64/26 - Position Reference Systems For Aeronautical Charts

To identify a combined operational requirement to adopt basic position reference systems for use on aeronautical charts produced by participating nations.

AIR-STD-64/27 - Standard Scales For Topographic Aeronauticalcharts

To identify an operational requirement to adopt standard scales for topographic aeronautical charts produced by participating nations.

AIR-STD-64/28 - Definitions Of Aeronautical Map And Chart And Flight Information Terms

To establish a directory of terms and their definitions so that participating air forces may use without special instructions.

AIR-STD-64/29 - Aeronautical Chart Catalogues

AIR-STD-64/30 - Flight Information Publication Terminal

To identify the operational requirement for Flight Information Publication Terminals and to promote the standardization of such products published by member ASCC nations to facilitate use by any of the participating air forces.

AIR-STD-64/31 - Identification Of Aerodrome By Name

To aid aircrew in the identification of aerodromes by the adoption of a common system for selecting the name under which the primary entry will appear in listings and on charts.

AIR-STD-64/32 - Aeronautical Chart Projections

AIR-STD-64/33 - Portrayal Of Navigation Grid Information

AIR-STD-64/34 - Identification Of Airspace Reservations (With Amendment 1)

To simplify the identification of Airspace Reservations in areas of common FLIP coverage by allotting to each Airspace Reservation a unique designator which indicates the country of location, the type of Airspace Reservation, and the serial number.

AIR-STD-64/35 - Maximum Elevation Figure Criteria For Aeronautical Charts

To standardize the computation of Mximum Elevation Figures to be shown within the designated quadrangles on the aeronautical charts.

AIR-STD-64/36 - Aircraft Arresting Sysems, Information For Flips

To standardize the presentation of information related to aircraft arresting systems in enroute supplement and on instrument approach charts (terminal).

AIR-STD-64/37 - Flip Operational Abbreviations

To maintain a decode list of the operational abbreviations used in member nations' Flight Information Publications (FLIPS) and aeronautical charts.

AIR-STD-64/38 - Asw Dead Reckoning Tracker Plotting Charts

To standardize the specifications of anti-submarine warfare plotting charts as used on PT 396 Dead Reckoning Tracter Equipment in order that maritime air forces of member nations may easily use each other's products.

AIR-STD-64/6 - Standard Units Of Linear Measurement On Aeronautical Charts And Flight Information Publications (Req Other Than Dod Ref Hq Usaf/X0Xx-Iso, Washg., Dc 20330-5058 ( No S/S Document)

To identify standard units of linear measurement to be used on aeronautical charts and Flight Information Publications to satisfy the combined operational requirements of the member air forces.

AIR-STD-64/94 - Guidelines For The Assessment Of Thermal Stress In Aircraft Chemical Defense Operations

AIR-STD-65 - Changes To Ascc Air Standards/Advisory Publications - Working Party 65 - Airfield Marking & Lighting & Other Visual Aids

AIR-STD-65/1 - Lighting Of Instrument And Non-Instrument Runways

AIR-STD-65/10 - Airfield Lighting Control Systems

To standardize the airfield lighting control systems.

AIR-STD-65/11 - Illuminated Runway Distance Markers And Illuminated Hook Cable Markers

To achieve standardization between ASCC nations on Illuminated Runway Distance Markers (IRDM) and Illuminated Hookcable Marker (IHCM) as visual aids to aircraft operations at military airfields.

AIR-STD-65/12 - Airfield Lighting For Category 11 Operations

AIR-STD-65/13 - Extraneous Lighting In Vicinity Of Aerodromes

AIR-STD-65/14 - Airfield Marking And Lighting Color Standards

To establish standard colours for aeronautical ground light and surface markings.

AIR-STD-65/15 - Airfield Lighting Circuitry

AIR-STD-65/16 - Helipad Lighting (Vmc)

To establish a system of helipad lighting for Visual Meteorological Conditions (VMC).

AIR-STD-65/17 - Aerodrome Illuminated Markers And Signs

AIR-STD-65/18 - Apron Floodlighting

AIR-STD-65/19 - Standby Power Supply Requirements For Fixed Installations

AIR-STD-65/2 - Lighting Of Airfield Obstructions (Rel To Other Than Dod Act Req Pri Appr Of Hq Usaf/Xoxx-Iso Wash, Dc 20330-5058)

AIR-STD-65/21 - Helipad Marking

To standardize the markings of helipads at heliports, other than those heliports which use a runway for the helicopter landing area.

AIR-STD-65/22 - Airfield Clearance Planes

AIR-STD-65/23 - Aircraft Arresting Gears For Airfields

To ensure that each member nation can use the aircraft arresting gears of other member nations and that the arresting gear design provides protection against loss or damage to the aircraft under defined engagement conditions.

AIR-STD-65/24 - Air Traffic Control Procedures For Arrestment Of Aircraft

To ensure that each Member Nation using aircraft arresting systems of other Member Nations can expect Air Traffic Control to comply with a standard procedure.

AIR-STD-65/25 - Signals For Runway Party When Disengaging An Aircraft After A Hook Cable Arrestment

To ensure that each Member Nation using the aircraft arresting gears of other Member Nations can expect the runway party to utilize standard hand signals when disengaging the hook cable and rewinding the hook cable.

AIR-STD-65/26 - Pilots Operating Procedure For Engagement Of Airfield Arresting Systems (Issued Controlled)

The purpose of this ASCC AIR STD is to standardize pilot's procedure for engagement of airfield arresting systems.

AIR-STD-65/3 - Lighting And Marking Of Airfield Obstructions

To standardize the marking of airfield obstructions.

AIR-STD-65/30 - Pacific Nations Helicopter Operations From Ships Other Than Aircraft Carriers (Pac Hostac) Publications (Pac Hostac (Pac 1) And Pac Hostac Supplement (Pac 1-1)

To register national acceptance of PAC HOSTING (PAC 1) and PAC HOSTING Supplement (PAC 1-1).

AIR-STD-65/31 - Airfield Tone-Down Marking (S/S By Air-Std-65/36)

To standardize airfield tone-down markings.

AIR-STD-65/32 - Non-Tactical Heliport Lighting And Marking (Issued Controlled)

To establish heliport marking and lighting systems for visual meteorological conditions (VMC) and instrument meteorological (IMC) at heliports.

AIR-STD-65/33 - Airfield Declared Distances

To standardize the terminology and criteria for airfield declared distances.

AIR-STD-65/34 - Heliport And Helipad Lighting And Marking

The purpose of this agreement is to standardize lighting and marking of Heliports and Helipads.

AIR-STD-65/37 - Aircraft Arresting Systems Operating Procedures

The purpose of this agreement is to standardize minimum Air Traffic Control actions, air-ground-air comminications, pilot procedures for aircraft arresting systems engagement and hand signals to be used by ground parties when disengaging and rewinding the hookcable following arrester systems engagement.

AIR-STD-65/4 - Airfield Approach Lighting

AIR-STD-65/5 - Marking Of Instrument And Non-Instrument Runways (S/S By Air-Std-65/36)

AIR-STD-65/6 - Airfield Taxiway Markings (S/S By Air-Std-65/36)

AIR-STD-65/7 - Visual Glide Slope Indicator Systems

AIR-STD-65/8 - Airfield Portable Lighting Systems

AIR-STD-65/9 - Taxiway Lighting

AIR-STD-70/10 - Standard Analogue Heading Outputs

To establish scale factors and synchro voltages for the transmission of healing information.

AIR-STD-70/11 - The Specification For Evaluation Of The Accuracy Of Inertial Navigation Systems

To adopt a standard method of determining the position accuracies of pure Inertial Navigation Systems.

AIR-STD-70/13 - The Specification For Evaluation Of The Accuracy Of Airborne Doppler Navigation Systems

To adopt a standard method of determining the position accuracies of airborne doppler navigation systems.

AIR-STD-70/14 - Definition Of Sea State For Use In Connection With Doppler Navigation

To adopt a definition of Sea State for use in connection with Doppler Navigation. In addition, this Standard and negotiated agreement will effectively promote economy in the use of national resources assigned to test purposes. It is the intent of ASCC Members to create, by the exchange and collection of standardized test information, a commonly available data bank in the area of Doppler Navigation.

AIR-STD-70/16 - The Specification For Evaluation Of The Accuracy Of Hybrid Navigation Systems

The purpose of this agreement is to adopt a standard method of reporting the geodetic position accuracies of HYBRID NAVIGATION SYSTEMS. The term HYBRID, in this case, refers to a navigation system employing both a self-contained system (INS, DOPPLER) and externally-referenced system (OMEGA, TACAN, GPS, etc).

AIR-STD-70/17 - Definitions Of Aircraft Attitude And Heading Angles

The purpose of this agreement is to define the terminology used when referring to aircraft attitudes and manouevres.

AIR-STD-70/18 - Microwave Landing Systems (Mls)

The purpose of this agreement is to ensure interoperability among Microwave Landing Systems (MLS) operated by member nations. It is envisaged that the existence of this agreement will facilitate attainment of a minimum acceptable performance and maximum interoperability between existing and future MLS equipment.

AIR-STD-70/3 - Interoperability Of Aircraft Vhf Am And/Or Fm Multi-Frequency Transceiver Installations And Compatible Ground Radio Equipments

The purpose of this agreement is to achieve interoperability. In order to enable participants more readily to be able to agree to the basic parameters necessary for interoperability, no attempt is made in this document to specify comprehensive equipment design standards. However, it is envisaged that the existence of this agreement will enhance future possibilities for the eventual realization of full standardization and module/component interchangeability.

AIR-STD-70/4 - Interoperability Of Aircraft Uhf Multi-Frequency Transceiver Installation And Compatible Ground Transmitters And Receivers

The intention of this agreement is to achieve UHF interoperability. In order to enable participants more readily to be able to agree to the basic parameters necessary for interoperability, no attempt is made in this document to specify comprehensive UHF equipment design standards. However, it is envisaged that the existence of this agreement will enhance future possibilities for the eventual realization of full equipment standardization and module/component interchangeability.

AIR-STD-70/7 - Data Transmission For Radar Doppler Systems

To establish data transmission criteria for use in doppler radar systems.

AIR-STD-70/8 - True Airspeed Outputs

AIR-STD-80/1 - Method Of Determining The Principal Sensitometric Characteristics Of Black And White Rolled Air Film

To adopt standard methods of determining the principal sensitometric characteristics of black and white rolled air films so that all services are able to recognize and properly use film supplied by any of the ASCC Forces.

AIR-STD-80/10 - Air Reconnaissance Request/Task Form

The purpose of this agreement is to standardize the format for requesting and tasking air reconnaissance by ASCC Armed Forces.

AIR-STD-80/11 - Titling Of Hand-Held Imagery (Wet)

The purpose of this agreement is to standardize the titling and reproduction of imagery which is reproduced as single frames for intelligence purposes, and which is exposed with hand-held cameras, so as to facilitate the handling, use and interchange of this imagery between the ASCC member nations.

AIR-STD-80/13 - Air Reconnaissance Intelligence Reporting Nomenclature

To standardize nomenclature for describing equipment and installations in imagery reports.

AIR-STD-80/14 - Point Designation Template For Imagery

To specify basic parameters to be observed in the construction of a universal grid for use in identifying a precise point of area on a frame of imagery.

AIR-STD-80/15 - Minimum Resolved Object Sizes For Imagery Interpretation

The purpose of this agreement is to specify minimum resolved object sizes required in imagery used for interpretation and technical analysis.

AIR-STD-80/18 - Reporting Of Data Used For Dimensional Analysis Of Imagery

The purpose of this agreement is to standardize the reporting of data used for dimensional analysis of imagery.

AIR-STD-80/3 - Dimensions, Tolerances And Characteristics Of 70Mm, 126Mm And 240Mm Rolled Film For Air Photography

To adopt standard dimensions, tolerances and characteristics for 70mm, 126mm, and 240mm rolled film for air photography, to permit the common use of film in cameras and processing equipment.

AIR-STD-80/5 - Target Pattern For Determination Of Aerial Photographic Resolution

The purpose of this agreement is to adopt a standard target pattern for determining the photographic resolution of aerial cameras used by ASCC nations during airborne operations.

AIR-STD-80/7 - Lm-230A/B Programmable Automatic Camera Test Set

AIR-STD-80/8 - Air Reconnaissance Intelligence Report Forms

To standardize and consolidate Air Reconnaissance Report Forms for reporting and presenting intelligence information derived from air reconnaissance and sensor imagery.

AIR-STD-84/11 - Casualty Handling In A Cw Environment

AIR-STD-84/12 - Peacetime Nuclear Weapons Accidents - Division Of Responsibilities

AIR-STD-84/13 - Peacetime Nuclear Weapons Accidents - Key Control Areas

AIR-STD-84/2 - Commander S Guide On The Effects Of Penetrating Ionizing Radiation (With Change 1)

To provide a standard method, within the ASCC member services, of categorizing the Radiation Exposure State of individuals, and groups of individuals, and to provide common guidance for Commanders.

AIR-STD-84/4 - First Aid Materiel For Chemical Injuries (With Change 1)

The purpose of this agreement is to standardize the minimum essential items of medical first-aid materiel for chemical injuries.

AIR-STD-84/9 - Nbc Defense Evaluation Of Air Bases

To identify the criteria for evaluating the effectiveness of Air Forces operating in an NBC environment.

AIR-STD-85/1 - Glossary Of Terms And Definitions

To achieve standardization of the listed terms and definitions through mutual use by the air forces of the United States, United Kingdom, Canada, Australia and New Zealand under the standardization principles of the ASCC Programme; to facilitate communication among the air forces of these nations; and to promote greater understanding by the common employment of mutually defined terminology.

AIR-STD-90/4 - Aircraft Arresting Systems Information For Flips

The purpose of this agreement is to standardize the presentation of information related to aircraft arresting systems in enroute supplement and on instrument approach charts (terminal).

AIR-STD-94/3 - Comparative List Of Ascc Terms And Definitions For Nuclear Accident Response

To provide a comparative list of terms and definitions used by Member nations related to Nuclear Accident Response.

AOP-15 ED.3 - Guidance On The Assessment Of The Safety And Suitability For Service Of Non-Nuclear Munitions For Nato Armed Forces

AOP-16 ED.4 - Fuzing Systems: Guidelines For Stanag 4187

AOP-22 ED.1 - Design Criteria And Test Methods For Inductive Setting Of Electronic Projectile Fuzes

AOP-7 ED.2 - Manual Of Data Requirements And Tests For The Qualification Of Explosives Materials For Military Use

The primary objectives of this document are to promote standardization and interoperability of munitions among the NATO countries.

AOP-8 ED.2 - Nato Fuze Characteristics Catalogue

The purpose of AOP-8 is to: a. show to fuze designers and munition developers the characteristics of existing fuzes thus avoiding that fuze designers enter into a development effort to arrive at fuze characteristics already available. It is not intended to include in the AOP statements on full interchangeability of fuzes as to from, fit and function or to cover logistical aspects. b. provide information on the conformance to safety standards of individual fuzes in accordance with STANAG 4157 and national safety standards.

AQAP-100 ED.3 - Policy On An Integrated Systems Approach To Quality Through The Life Cycle

This document should be used, as a part of the overall policy of an organisation, to ensure quality of life cycle processes, products and services.

AQAP-11 - Nato Guideline For Specification Of Technical Publication

AQAP-110 ED.2 - Nato Quality Assurance Requirements For Design, Development And Production

AQAP-119 ED.2 - Nato Guide To Aqaps-110, -120, -130

AQAP-120 ED.2 - Nato Quality Assurance Requirements For Production

This document establishes requirements for a quality system, herein referred to as the System, to be established and maintained by the contractor for the purpose of demonstrating that product conforms to contract requirements and for the furnishing of objective evidence.

AQAP-130 ED.2 - Nato Quality Assurance Requirements For Inspection And Test

This document establishes requirements for an inspection system herein referred to as the System to be established and maintained by the contractor for the purpose of demonstrating that product conforms to contract requirements and for the furnishing of objective evidence.

AQAP-131 ED.1 - Nato Quality Assurance Requirements For Final Inspection

This document establishes the requirements for the contractor's final inspection (including testing as necessary) to be performed to demonstrate that product conforms to contract requirements and for the furninhing of objective evidence.

AQAP-150 ED.2 - Nato Quality Assurance Requirements For Software Development Aqap-150

This publication specifies the project oriented requirements to manage the quality of the software development process.

AQAP-159 ED.2 - Guidance For The Use Of Aqap-150

This publication specifies the project oriented requirements to manage the quality of the software development process.

AQAP-170 ED.2 - Nato Guide For The Delegation Of Government Quality Assurance

This document provides guidance for the delegation and acceptance of GQA under the conditions of STANAG 4107, and identifies the elements involved in planning and implementing surveillance activities. It describes the delegator s responsibilities to identify quality risks and to detail related tasks for inclusion in the Request for Government Quality Assurance (RGQA). Refer to Annex A.

AQAP-8 - Nato Guide To The Preparation Of Specifications For The Procurement Of Defence Material

ARMP-1 ED.4 - Nato Requirements For Reliability And Maintainability

ARMP-2 ED.2 - General Application Guidance On The Use Of Armp-1

ARMP-3 ED.2 - List And Source Of National And International Reliability And Maintenability Documents

ARMP-3 catalogues R&M Standards and other documents, military and civilian, which are produced by NATO countries.

ARMP-4 ED.4 - Guidance For Writing Nato R&M Requirements Documents

ARMP-6 ED.3 - Guidance For Managing In Service R & M

QAP-15 - Glossary Of Terms Usedin Proof (Rel To Other Than Dod Agencies Must Be Approved By Darcom, Drcde)

This QAP has been approved for use by the Armies of the United States, United Kingdom, and Australia and the Canadian Forces, as a Glossary of Terms used in Proof.

QAP-17 - Metallurical Terms & Definitions, Listing Of Glossaries Used By Armies (Req Other Than Dod Ref To Darcom, Drcde-1)

QAP-22 - Military Operations In Urban Terrain - Bibliography

QAP-9 - Engine Health Monitoring For Army Aircraft, Manual (Abca) (Release To Other Than Dod Requires Prior Approval Of Hq Darcom Drcird

QSTAG-101 ED.A - Standardization Of 2 Inch Fuze Holes And Fuze Contours For Artillery Projectiles 75Mm And Larger In Caliber Including 81Mm, 4. 2 Inches And 107Mm Mortars

This standard has been approved by the Armies of the United States, United Kingdom, Canada, and Australia as a design standard for projectile fuze threads (2-12 UNS-1B) and fuze contours for artillery projectiles, 75mm and larger in caliber including 81mm, 4.2" and 107mm nortars to insure ballistic matching and physical interchangeability.

QSTAG-105 - Sampling Procedures And Tables For Inspection By Attributes (Abca-105)

The Armies of the United States, United Kingdom and Australia and the Canadian Forces have standardized sampling procedures and tables for inspection by attrihutes.

QSTAG-108 ED.1 - Link, Cartridge, Metallic Belt 7.62Mm, M13 (Including Amendments 1 Thru 6)

The Link, Cartridge, Metallic Belt, 7.62mm, M13 has been approved for use by the Armies of the United States and United Kingdom and Canadian Forces and meets current requirements for link to be used in combination with the NATO 7.62mm cartridge.

QSTAG-109 ED.1 - Interchangeability Criteria For Batteries, Storage (Batteries, Secondary) (Lead - Acid Type)

QSTAG-111 ED.1 - U.S. Printing Press, Offset (Lithographic, Motor Driven, Mobile).And U.K. Machine Printing, Rotary, Lithographic, Offset, Two Colour (Abca-111)

QSTAG-112 - Water Purification Unit Van Body Mounted, Electric Motor-Driven, Erdlator-Type Clarifier, Diatomite Type Filters, 1500 Gph (Abca-112)

The Water Purification Unit, Van Body Mounted, Electric-Motor Driven, ERDLATOR-Type Clarifier, Diatomite-Type Filters, 1500 GPH has been approved as a standard for use by the United States Army and Canadian Forces.

QSTAG-113 - Specification For Ce (Tetryl)-(Abca-113)

This agreement has been approved by the Armies of the United States and United Kingdon and Canadian Forces as the standard minimum requirement for the propellant ingredient CE (Tetryl) to make it acceptable to the three armies, when manufactured for delivery from one ABC Army to another.

QSTAG-114 - Specification For Picrite (Nitroguanidine)-(Abca-114)

This agreement has been approved by the Armies of the United States and United Kingdom and the Canadian Forces as the minimum requirement for Picrite (Nitroguanidine) manufactured for delivery between the three countries.

QSTAG-115 - Specification For Rdx (Hexogene)-(Abca-115)

This agreement has been approved by the Armies of the United States and the United Kingdom and the Canadian Forces as the standard minimum requirement for RDX (Hexogene) for deliveries from one ABC army to another.

QSTAG-116 - Specification For Petn (Penthrite)-(Abca-116)

This agreement has been approved by the Armies of the United States and the United Kingdom and the Canadian Forces as the standard minimum requirement for PETN (Penthrite ) for deliveries one subscribing army to the other.

QSTAG-117 - Specification For Ammonium Nitrate (For Use In Explosives)-(Abca-117)

This agreement has been approved by the Armies of the United States and the United Kingdom and the Canadian Forces as the standard minimum requirements for Ammoniu Nitrates (for use in explosives) for deliveries from one ABC Army to another.

QSTAG-118 - Specification For Tnt (Tolite) Abca-118

This agreement has been approved by the Armies of the United States and the United Kingdom and the Canadian Forces as the standard minimum requirement for TNT (Tolite) for deliveries from one ABC country to another.

QSTAG-121 ED.1 - Rules Governing The Interchangeability Of Securing And Holding Devices For Infrared Scopes On Carbines, Rifles And Light Machine-Guns (Abca-121

QSTAG-122 ED.1 - Lamps For Tactical Vehicles (Abca-122)

QSTAG-123 ED.2 - Small Arms Ammunition (7.62Mm)

The subject of this agreement is functional interchangeability of 7.62mm ammunition.

QSTAG-125 ED.2 - Charger For Nato 7.62 Mm Ammunition (Based On Nato Stanag 2318) (Abca 125)

The subject of this agreement is functional interchangeability of the Charger for the 7.62MM Ammunition.

QSTAG-128 ED.1 - Interchangeability Of Infrared Equipment Mounted On Portable Infantry Weapons Optical Alignment Of The Telescope (Abca-128)

QSTAG-129 ED.2 - Standardization Of Inpact Tests For Steel For Guns (Based On Nato Stanag 4020) (Abca 129)

QSTAG-13 ED.2 - Immersion Requirement For Ground Role Service Equipment (Based On Nato Stanag 2842) (Abca) Edition 2

The aim of this agreement is to establish criteria for the immersion of applicable equipment used by the ABCA forces when operating in a ground role.

QSTAG-130 ED.1 - Nato Symbol Of Interchangeability (Abca-130)

QSTAG-131 ED.1 - Marking Of Ammunition (And Its Packaging) Of A Calibre Below 20Mm (Abca-131)

QSTAG-134 ED.2 - Specification For Dnt (Dinitrotoluene) For Propellants

QSTAG-140 ED.1 - Overall Dimensions Of Battery Spaces For Tactical Vehicles (Abca-140)

QSTAG-141 - Boat, Bridge Erection, Inboard Engine, Aluminum, 27 Ft. (Abca-141)

QSTAG-142 - Outboard Motor 25 Hp, Gasoline, With Carrying Chest (Abca-142)

The 25 Horsepower (HP) Outboard Motor, Gasoline, with Carrying Chest, has been approved as a standard for use by the Armies of the United States and Canada.

QSTAG-145 - Interchangeability Of Infrared Equipments Mounted On Portable Infantry Weapons-Shape And Dimensions Of Infrared Filters (Abca-145)

QSTAG-146 ED.2 - Cord, Detonating, (Abca-146)

QSTAG-148 ED.2 - Borescopes M1 & M3

QSTAG-150 ED.2 - Gun, Field Artillery, Self Propelled, 175Mm, M107 With Ammunition And Associated Stores (Abca 150)(No S/S Document)

The Gun, Field Artillery, Self-Propelled, 175MM, M107, with Ammunition and Associated Equipment, has been approved for use by the United States and the United Kingdom.

QSTAG-151 ED.3 - Carrier, Personnel, Full Tracked, Armored, M113A1/A2/A3 And Carrier, Command Post, Light Tracked, M577A1/2

QSTAG-152 ED.2 - Plate, Base, 81Mm Mortar, Cdn, Mk1

The Plate, Base, 81mm Mortar, CDN, MK1 has been approved for use by the Armies of the United States, United Kingdom and Australia, and the Canadian Forces, as the standard base plate for medium mortars.

QSTAG-156 ED.1 - Hood, Tank Protective Mask, M5 (Abca-156)

QSTAG-157 - Gun, Spotting, Cal. 50, M8C And M8 And Cartridge, Spotter Tracer, Cal. 50, M48A1 (Abca-157)

QSTAG-159 - Grenade, Hand Rifle, Smoke, Wp, M34 (Abca-159)

The US "Grenade, Hand-Rifle, Smoke, WP, M34" has been approved by the Armies of the United States, United Kingdom, Canada and Australia as functionally interchangeable with the British "Grenade, No. 80, WP, Mk 1" for use as a hand grenade only.

QSTAG-16 ED.2 - Designation Of Armor Thickness And Obliquity (Abca-16)

This agreement has been approved by the Armies of the United States, United Kingdom and Australia and Canadian Forces to standardize the method of expressing armor thickness and obliquity.

QSTAG-160 ED.1 - Radio Set A/Prc77 (Use Qstag 467)

QSTAG-161 - Radio Sets.An/Vrc-12 Series (Abca 161) W/Amds 1, 2 And 3

The Armies of the United States, Canada and Australia have approved the following radio sets for use in military applications requiring short range, two-way, vehicular, frequency-modulated (fm) voice communications in the frequency range of 30.000 to 75.00 megacycles.

QSTAG-162 ED.2 - 3 And 6 Hp Air Cooled Gasoline Engines (Abca-162)

The United States Army and the Canadian Forces have agreed to standardize the design for the 3 and 6 horsepower (Hp) gasoline engines, air cooled, for use as prime movers in military applications for equipment under design control of the Armies.

QSTAG-163 ED.3 - Military Abbreviations

The Armies of the United States , United Kingdom and Australia and the Canadian Forces have agreed to standardize the use of abbreviations in military writing.

QSTAG-165 ED.2 - Movements Principles, Policies, And Duties

The Armies of the United States, United Kingdom and Australia and the Canadian Forces, have agreed to standardize the movements principles, policies, and duties which are considered desirable in the details of agreement.

QSTAG-171 ED.2 - Procedures For Requesting Repair And Recovery Of Land Military Technical Equipment

QSTAG-18 - Metric System For The Measurement Of Weapon Calibres And Ammunition Agreement (Abca-18)

QSTAG-180 ED.4 - Military Load Classification Of Bridges (Computation Of Bridge, Ferry, Raft And Vehicle Classifications)

QSTAG-182 ED.2 - Battlefield Illumination

QSTAG-187 ED.5 - Reporting Nuclear Detonations, Biological And Chemical Attacks And Predicting And Warning Of Associated Hazards And Hazard Areas

QSTAG-189 ED.3 - Friendly Nuclear Strike

QSTAG-19 ED.1 - Military Operations In Urban Terrain Computer Model Evaluation, Armies Standardization Program (Abca Quadripartite 19)

Nearly all existing computer models of combat have been designed principally for mechanized warfare in rural terrain and do not adequately represent battle in urban areas.

QSTAG-2 - Military Load Classification Of Civil Bridges By The Reconnaissance And Correlation Methods

QSTAG-20 ED.1 - Non Ferrous Metal And Alloy Specifightions

QSTAG-200 ED.1 - Climatic Enviornmental,Conditions Affecting The Design Of Military Material (Use Qstag 360)

QSTAG-201 ED.2 - Abca Table Of Medical Equivalents Of Medical Material

QSTAG-203 - Cables, Coaxial And Twin Conductor, For Radio Frequency (Abca-203)

QSTAG-204 ED.1 - Connector, Military Power And Lighting (Abca-204)

QSTAG-207 ED.2 - Calculator Set, Radiac And Nuclear Yield, Abc-M28A1 (Abca-207)

The Calculator Set, Radiac and Nuclear Yield: ABC-M28A1 has been approved by the Armies of the United States, Canada, and Australia for use in nuclear warfare in calculating past, present, or future dose rates and nuclear yield.

QSTAG-208 ED.2 - Headlamp Light Unit For Wheeled Tactical Vehicles (Abca 208)

The Armies of the United States, Australia and the Canadian Forces, agree to standardize the overall dimensions of the headlamp light unit for wheeled tactical vehicles (consisting of a reflector, bulb with socket and lens).

QSTAG-209 - Definition Of Weight Of A Standard Manpack Radio Station (Abca-209)

QSTAG-21 ED.2 - Trilateral Design & Test Code For Military Bridge & Gap Crossing Equipment

QSTAG-211 ED.1 - Detector Kit, Chemical Agent, Abc-M18A2 (Abca-211)

QSTAG-212 - Infrared Lighting Equipemnt For Militaay Vehicles (Abca-212)

QSTAG-213 ED.2 - Camouflage Standards

QSTAG-214 - Filter, Gas Particulate, Cfm S, 600, Abc14, 1200, Abc-M15, 2500, Abc-M16, 5000, Abc-M17, 600, Abcm14A1, 1200, Abc-M15A1, 2500, Abc-M16A1, 5000, Abc-M17A1 (Abca-214)

QSTAG-215 ED.1 - A.C. Synchros (60 Hz And 400Hz) (Abca-215)

QSTAG-216 - Carrier, (Us), Field Protective Mask, Abc M13A1 (Ca) Carrier, Nbcw Protective Mask, M14 (C1A1)

QSTAG-217 ED.2 - Artillery, Tactical Tasks & Responsibilities For Control Of

QSTAG-218 - Filter Unit, Gas Particulate, Hospital, Six Man, 12 Cfm, M7A1

QSTAG-219 ED.1 - Us Decontaminating And Reimpregnating Kit, Individual, M13 (E21R7), Uk Decontamination Kit, Personal (Dkp), Ca Mitt, Decontaminating, Cw Agent (Abca-219)

QSTAG-220 ED.2 - Adoption Of A Standard Cannon Artillery Firing Table Format

QSTAG-221 - Target Numbering System For Post-1970 (Abca-221)

QSTAG-222 ED.3 - Common Critical Marrying Up Procedures

QSTAG-223 - Decontamination Apparatus, Power Driven, Skid Mounted, Multi Purpose, Nonintegral, 500 Gallon, M12A1

QSTAG-224 ED.2 - Manual Fire Direction Equipment, Target Classification And Methods Of Engagement (Abca 224)

QSTAG-225 ED.2 - Call For Fire Procedures (Abca 225)

QSTAG-226 ED.2 - Mortar, Medium, Ground Mounted 81Mm, & Ammunition

QSTAG-227 - Lubricant Fittings (Abca-227)

QSTAG-228 ED.2 - Connectors For Multi-Pair Field Telephone Cables (Abca-228)

QSTAG-229 - Abbreviations For Use On Drawings (Abca-229)

QSTAG-23 - Safety And Environmental Tests For Land Mines And Demolition Stores (Abca 23)

QSTAG-230 ED.2 - Morphia Dosage Agreement

The aim of this agreement is to standarise within the ABCA Force the range of initial dose of morphia to be administered to combat casualties and the method of marking patients to whom morphia has been administered.

QSTAG-231 ED.1 - Cases, Medical Instrument And Supply Sets, Non Rigid Nos 3 And 5 (Abca-231)

This agreement has been approved for use by the Armies of the United States, Canada and Australia as a design standard for medical instrument and supply cases, non-rigid Nos. 3 and 5.

QSTAG-232 - Insecticide Powder, Personal Application, 1 Per Cent Malathion, 25 Pound Pail (Abca-232)

QSTAG-233 ED.2 - Radio Set, An/Grc-103 (Abca-233)

QSTAG-234 - Mask, Chemical And Biological Aircraft, Abc-M24 And Hood, Aircraft, Chemical And Biological Mask, Abc-M7

QSTAG-235 - Decontaminating Apparatus, Portable, 1-1/2 Quart With Decontamination Agents (Abca-235)

QSTAG-236 ED.1 - Medical Gas Cylinders (With Amendment 1 Thru 3)

The Armies of the United States, United Kingdom, Australia and the Canadian Forces have agreed to adopt, for their medical services, a standardized range of special adapters, medical gas cylinders of up to and including 12 pounds, or 5.5 liters water capacity and color code for medical gas cylinders.

QSTAG-237 - Water Purification Unit Cargo Body Mounted, Electric Motor Driven, Erdlator Type Clarifier, Diatomite Type Filter, 600 Gph, Type Ii (Abca-237)

QSTAG-238 - Minimum Criteria For Lower Echelon (Unit) Level 2 - Wire Magneto Field Telephone Sets (Abca-238)

QSTAG-239 - Standard Procedure For Infantry/Armored Fighting Vehicle Target Indication (Abca-239)

QSTAG-240 - Equipment For Receipt And Delivery Of Liquid Fuels (Abca-240)

QSTAG-241 ED.1 - Packaging, Packing And Container Marking Of Electron Tubes (Valves) And Semi-Conduct

QSTAG-242 ED.1 - Detector Kits, Chemical Agent (Us) - Vgh, An-M15A2A (Uk) - Residual Vapour No. 1, Mk 1

QSTAG-243 - Surveillance (Including Night Observation) Plan Annex To An Operation Order (Abca-243)

QSTAG-245 ED.2 - Minimum Requirements For Water Potability (Short And Long Term Use)

The Armies of the United States, United Kingdom, Canada and Australia have agreed, when operating on land, to adopt minimum requirements as specified in the Details of Agreement for potability of drinking water to be issued to troops in combat zones or in any other strict emergency situations.

QSTAG-246 ED.2 - Radiotelephone Procedures For The Conduct Of Artillery Fire

QSTAG-247 - Unified Screw Threads (Abca-247)

QSTAG-248 ED.2 - Identification Of Medical Materiel To Meet Urgent Needs

QSTAG-249 ED.1 - Riot Control Agent Cs2 (Abca-249) (Replaced By Qstag 495)

QSTAG-250 - Helicopter, Light Observation, Oh58 Series

QSTAG-251 ED.2 - Alarm, Chemical Agent, Automatic, Portable, M8 & M8A1 With Accessories

The Armies of the United States and Australia have approved the Alarm, Chemical Agent, Automatic : M8 and M8A1 as standard equipment for providing combat and service elements of the army with a portable detection and alarm capability for the presence of chemical agents.

QSTAG-252 - Adoption Of A Standard Artillery Computer Meteorological Message

QSTAG-253 - General Drawing Practice (Abca-253)

QSTAG-255 - Mine, Antipersonnel M16A1, M16A2 And Fuze Mine Combination M605 (Abca 255)

QSTAG-257 - Color Of Indicating Smoke For Practice Land Mines And Land Mine Simulators (Abca-257)

QSTAG-258 ED.1 - Catalogue Of Ferrous Metals Specifications - Commercial And Service (Abca 258)

QSTAG-259 ED.1 - Equivalent Llectrical Insulating Materials (Abca-259)

QSTAG-26 - Artillery Fire Control Matrix

QSTAG-260 ED.1 - Testing Methods For Elastomers

QSTAG-261 ED.1 - Methods Of Test - Ferrous Metals

QSTAG-262 - Methods Of Specifying Steels In Manufacturing Data (Abca-262)

QSTAG-263/1 ED.A - Standards To Achieve Interoperability Of Abca Armies High Frequency Combat Net Radio Equipments

QSTAG-263/2 - Standards To Achieve Interoperability Of Abca Armies Very High Frequency Combat Net Radio Equipments

QSTAG-263/3 ED.C - Standard To Achieve Interoperability Of Abca Armies Ultra High Frequency Combat Net Radio Equipments

QSTAG-264 - Lunettes, Pintles And Emergency Towing Facilities (Abca-264)

QSTAG-265 - Sampling And Analyzing Kit, Cbr Agents, M19 (Abca-265)

QSTAG-266 - Standardization Of Combat Identification Markings For Armored Fighting Vehicles (Afvs)

QSTAG-267 - Standard Character By Character Meteorological Message Format (Abca)

QSTAG-271 - Performance And Protective Properties Of Combat Clothing (Abca 271)

QSTAG-274 - Certification Of Radiographic Testing Personnel Abca 274

QSTAG-275 ED.2 - Graphical Symbols For Electrical And Electronic Diagrams

QSTAG-276 ED.2 - Family Of Aerial Vehicles For Land Forces Up To The Year 2000

QSTAG-278 - Standardization Of Proof Practices For Pyrotechnic Stores Abca 278

QSTAG-28 - Switchboard Sb-22()/Pt

The Switchboard SB-22()/PT has been approved for use by the Army of the United States and the Canadian Forces as the adopted type for a lightweight field type telephone switchboard.

QSTAG-280 - Static Proof Of Detonators

QSTAG-281 - Static Proof Of Igniferous Initiators (Abca 386)

QSTAG-282 - Static Proof Of Caps (Other Than Small Arms) (Abca 282)

The Armies of the United Kingdom and Australia, and the Canadian Forces, have standardized the methods of static testing and proving of Caps (other than SAA).

QSTAG-283 - Area Predictor, Radiological Fallout, M5A2 (Abca 283)

The Area Predictor, Radiological Fallaout, M5A2 has been approved by the Armies of the United States, Australia and the Canadian Forces as design standard for determining fallout area and hazard resulting from tactical nuclear detonation.

QSTAG-284 ED.2 - Fifth Wheel Attachments

It has been areed by the Armies of the United States, the United Kingdom, Canada and Australia that the design standards for two fifth wheel kingpins and for the location and height of fifthe wheel attachments on tractors and semi-trailers are to be as recorded in the Details of Agreement.

QSTAG-286 ED.1 - Use Of Nomenclature - First Aid Kit

QSTAG-287 ED.3 - Procedure For Reporting And Initial Disposition Of Unsatisfactory Medical Materiel

The Armies of the United States, United Kingdom, Australia and the Canadian Forces have agreed, when a cross servicing of medical supplies exists, to adopt a standard procedure for reporting or recalling unsatisfactory medical materiel as specified in the Details of Agreement.

QSTAG-288 ED.1 - Intravenous Replacement Fluids (With Amd.2)

The Armies of the United States, United Kingdom, Australia and the Canadian Forces have agreed that intravenous replacement fluids will be available at field medical units providing first, second, and third echelon medical care as specified in the Details of Agreement.

QSTAG-289 ED.3 - Minimum Essential Characteristics Of Blood Shipping Container

QSTAG-290 ED.2 - Minimum Requirements For Controlled Temperature Storage Of Medical Material

The Armies of the United States, United Kingdom and Australia and the Canadian Forces have agreed to adopt basic requirements as specified in the Details of Agreement to ensure proper storage and transport of drugs, biologicals, chemicals and other medical items which are subject to rapid deterioration if controlled temperature requirements are not met.

QSTAG-291 - Interface Of Medical Material Procedures

QSTAG-292 - Vaccination Of Armed Forces

The Armies of the United States , United Kingdom and Australia, and the Canadian Forces have agreed to immunize members, in accordance with the Details of Agreement, during basic training to protect them from certain diseases existing in areas where they may be required to serve: and subsequently to maintain their immunity.

QSTAG-293 - Materiel For Emergency Medical Care Of Mass Casualties (Abca-293)

The Armies of the United States, United Kingdom and Australia and the Canadian Forces have agreed to establish and maintain the capability for providing material at short notice to be used in the emergency medical care of mass casualties by effecting the implementing procedures listed in paragraph la of the Details of Agreement.

QSTAG-296 - Filter Unit, Gas Particulate, Ged Or Emd, 200 Cfm, Abca M6A1 Abca 296

The Filter Unit, Gas-Particulate, GED or EMD, 300 CFM, ABCA-M6A1 has been approved for use by the Armies of the United States, Canada, and Australia as a design standard for colltective protection against toxic war agents for field installations.

QSTAG-298 - Electrical Characteristics Of Rotating 28 Volt D.C. Generating Sets For Field Army Use (Abca-298)

The Armies of the United States, United Kingdom and Australia and the Canadian Forces have agreed to standardize certain electrical characteristics of rotating 28 volt direct current (d.c.) generating sets in order that they will be functionally interchangeable with generating sets of any ABCA Army for field army use.

QSTAG-299 - Electrical Characteristics Of Rotating Alternating Current Generating Sets For Field Army Use (Abca-299)

The Armies of the United States , United Kingdom and Australia and the Canadian Forces have agreed to standardize certain Electrical Alternating Current (a.c.) Power Supply Characteristics of rotating a.c. generating sets for field army use in order to be completely functionally interchangeable with the systems of any ABCA Army in emergency field conditions.

QSTAG-300 - Telegraph And Data Transmission Rates (Abca 300)

The Armies of the United States , United Kingdom, and Australia and the Canadian Forces have agreed to standardize the rates used for telegraphic and data transmission (listed in the Details of Agreement)in order to ensure interoperablility of the communications systems of the ABCA Armies when handling such traffic.

QSTAG-301 - Characteristics Of Demolition Accessories To Determine Their Operational Interchangeability Abca 301

The object of this Agreement is to determine the characteristics which must be met by demolition accessories in use in the NATO Armed Forces, in order that they may be operationally interchangeable.

QSTAG-303 - Frequency Shift Standards For Hf/Ratt And Vhf/Ratt Operations (Abca 303)

QSTAG-304 - Operational Meteorological Messages And Forecasts (Abca 304)

The Armies of the United States, United Kingdom, and Australia, and the Canadian Forces, have agreed on the use of standard meteorological message formats to exchange operational meteorological data between units of different ABCA forces, as set out in the Details of Agreement.

QSTAG-305 - Tent, Frame Type, Maintenance, Medium, Light Mental, Expandable (Abca - 305) 150274

The Tent, Frame Type, Maintenance, Medium , Light Metal, Expandable, FSN 8340-951-6419, is approved by the US Army and the US Army and the Canadian Forces to provide a portable, lightweight maintenance tent for tracked wheeled vehicles.

QSTAG-306 - Fortification For Parked Aircraft (Abca-306)

The Armies of the United States, United Kingdom and Australia and the Canadian Forces have agreed to standardize on the design parameters and specifications for constructing and maintaining revetments of variuos types to protect parked military aircraft from damge caused by bullets and exploding non-nuclear munitions and fuel near (to the sides, but not aboce) the aircraft.

QSTAG-307 - Characteristics Of 28V Dc Electrical Systems In Military Vehicles (Abca-307)

The Armies of the United States, United Kingdom, Australia and the Canadian Forces agree to a design standard to establish the characteristics of 28 volt Electrical Systems in Military Vehicles, and hence provide for compatibility between vehicular electric power supply and utilization equipment.

QSTAG-309 - Definition Of Pressures For Use In The Design And Proof Of Guns And Ammunition (Abca-309)

The Armies of the United States, United Kingdom, and Australia and the Canadian Forces have agreed to adopt the list of definitions of pressures for use in the design and proof of guns and ammunition as set out in Annexes A and B.

QSTAG-31 ED.1 - Pumping Assembly, Flammable Liquid, Bulk Transfer, Gasoline Engine Driven, 50 Gpm (Us Gallons) (Abca-31)

The pumping assembly, Flammable Liquid, Bulk Transfer, Gasoline Engine Driven, 50 GPM (US Gallons), Barnes Model (federal Stock No. 4320-271-1858) is approved by the Army of the United States and the Canadian Forces to provide a portable gasoline dispensing pump capable of transferring all types of gasoline to vehicular tanks or individual containers from aboveground or underground storage tanks, railroad tank cars, and tank trucks.

QSTAG-310 - Braking Systems Between Towing And Towed Units Of Equipment Combinations For Military Use (Abca 310)

The Armies of the United States , United Kingdom and Australia and the Canadian Forces have agreed to adopt certain design features that will ensure functional interchangeability in braking systems between towing and towed equipment for military use.

QSTAG-312 - Radio Receiving Set, An/Arn-82 (Abca-312)

The Armies of the United States and Australia and the Canadian Forces have agreed to standardize parameters of design and performance to achieve interoperability of VHF-Omnirange Radio Receiving Set.

QSTAG-313 - Direction Finder Set, An/Arn-89(No S/S Document)

The Armies of the United States and Australia and the Canadian Forces have agreed to standardize parameters of design and performance to achieve interoperability of Direction Finder Set, AN/ARN-89.

QSTAG-314 - General Purpose Vented Nickel Cadmium Batteries (Abca-314)

This agreement sets out the required characteristics of vented nickel-cadmium batteries and their respective cells or monoblocks for replacement in and maintenance of these batteries.

QSTAG-315 - Batteries, Rechargeable, Nickel Cadmium, Sealed

This agreement sets out the required characteristics of sealed nickel-cadmuim batteries.

QSTAG-316 ED.1 - Stove, Gasoline Burner, M1950, And Case (Abca-316)

QSTAG-317 - Disperser, Riot Control Agent, Portable, 3 Gallon, M33A1 And Service Kit, Portable, Riot Control Agent Disperser, M254

QSTAG-319 - Grenade Hand, Riot, Cs, M47 And Grenade, Hand, Roit, Red Smoke, M48

QSTAG-322 ED.1 - Emergency War Surgery (With Amendment 1)

The Armies of the United States, United Kingdom and Australia and the Canadian Forces have agreed to standardise the emergency war and initial surgery principles for treatment of war wounded.

QSTAG-323 - Welding Symbols (Abca-323)

QSTAG-324 - Welding Terms And Definitions (Abca-324)

QSTAG-325 ED.1 - The International System (Si) Units & Their Application

QSTAG-326 - Graphical Symbols For Use In Diagrams For Fluid Systems In Army Vehicles (Excluding Aeronautic Or Guided Weapon )Missile(System)

QSTAG-327 ED.3 - Twelve Point Electrical Connectors Between Military Vehicles

QSTAG-328 ED.2 - Slinging And Tiedown Provisions For Lifting And Tying Down Military Equipment

QSTAG-329 ED.1 - General Requirements & Common Tests For Precision Instrument Rotating Servo Components

QSTAG-332 - Standard Ballistic Meteorological Message(Abca 332)

QSTAG-334 - Proof Testing Of Small Arms (Abca 334)

QSTAG-335 - Certification Of Industrial Ultrasonic Testing Personnel (Abca-335)

QSTAG-337 - Glossary Of Air Defense Terms

QSTAG-338 ED.1 - Endless Vee Belts And Pulleys Automotive, Industrial And Fractional Horsepower011077

QSTAG-339 - Test Procedures For Barium Nitrate (Abca 339)

QSTAG-340 - Single & Multi Level Continuous Sampling Procedures & Tables For Inspection By Attributes (Abca 340)

QSTAG-342 - Test Procedures For Magnesium Power (Abca 342)

QSTAG-343 - Basic Requirements For Electronic Surveillance Of Patients In The Field (Abca 343)

QSTAG-344 - Basic Voltage And Current Characteristics Of Electro-Medical Equipment (Abca 344)

QSTAG-345 - Essential Characteristics Of High Pressure Steam Sterilizers (Abca 345)

QSTAG-346 - Standard List Of Gap Crossing Information Requirements When Gathering Data By Means Of Aerial Or Ground Survey

QSTAG-347 - Batteries, Rechargeable, Lead Acid, Vented (Abca 347)

This agreement sets out the required characteristics of rechargeable vented lead-acid batteries.

QSTAG-348 - Batteries, Non Rechargeable

QSTAG-349 ED.1 - Battery Chargers For Lead Acid Batteries

QSTAG-35 - Teletypewriter Set An/Pgc-1() (Abca-35)

QSTAG-351 - 5.56Mm Ammunition (Abca-351)

QSTAG-353 ED.2 - Metric (Iso) Screw Threads Coarse Series ( (Abca 353)

QSTAG-355 ED.1 - Blocks For Fiber Rope (Abca 355

QSTAG-356 ED.1 - Fiber Rope (Natural And Synthetic) (Abca 356)

QSTAG-357 - Marking Of Gas Cylinders (Excluding Medical)

QSTAG-358 - Test Procedures For Dextrinated Lead Hzide (Abca 358)

QSTAG-359 - Test Procedures For Black Power (Abca-359)

QSTAG-360 - Climatic Environmental Conditions Affecting The Design Of Military Materiel (Abca 360)

QSTAG-361 - Fungal Contaminants Affecting The Design Of Military Materiel (Abca 361)

QSTAG-362 - Chemical Environmental Contaminants Affecting The Design Of Military Materiel (Abca 362)

The purpose of this Agreement is to give particulars of the more common chemical contaminants which materiel of the ABCA Armies could encounter during their planned service life and offer general guidance on laboratory corrosion testing.

QSTAG-363 ED.1 - Radiation Environments Affectings Design Criteria

QSTAG-364 - Handling & Transport Shock & Vibration Conditions Affecting Design Criteria (Abca 364)

QSTAG-365 - The Fire Environmental Conditions Affecting Design Criteria (Abca 365)

The purpose of this agreement is to establish descriptions of the six types of fire enviroment listed in clause 1.2 and the explosive atmospheres to which military materiel of the ABCA Armies could be exposed during service.

QSTAG-386 - Standard Format Of Request For Meteorological Messages (Abca 386)

QSTAG-389 - Standard Target Acquisition Meteorological Message (Abca)

QSTAG-390 ED.2 - Helicopter, Cargo/Troop Carrier, Ch-47 Series

QSTAG-393 - Rocket & Launcher 2.75 (Abca 393)

QSTAG-397 ED.1 - Design Standardization Of Spark Plugs

QSTAG-398 - Adapters For Gas Cylinder Valves And Regulating Equipment

QSTAG-399 - Aircraft Communications Radio Set, An/Arc-114 Series

QSTAG-400 - Aircraft Communications Radio Set, An/Arc-115

QSTAG-401 - Aircraft Communications Radio Set, An/Arc-116

QSTAG-402 - Low Reflective Acrylic Lacquer For Rotary Wing Aircraft (Abca 402)

QSTAG-404 - M134 Machine Gun High Rate 7.62Mm, Minigun, (Gau-2B/A)

QSTAG-406 - Transfusion Equipment For Medical Use (Abca-406)

QSTAG-407 ED.1 - Standard Formats For Plans Of Test And Test Reports

QSTAG-409 - Afv Recognition Training Pack

The purpose of this agreement is to standardize, for the use of the American, British, Canadian and Australian Armies, a method of training all arms personnel to recognize allied and enemy armored fighting vehicles on the battlefield.

QSTAG-413 - Describing Physical Characteristics Of Stano Equipment (Abca 413)

QSTAG-414 - Tubes, Uniform Standards For Specifying Performance Parameters Of Image Intensifier (Abca)

QSTAG-415 - Uniform Standards For Specifying Performance Parameters Of Thermal Imaging Devices) (Abca 415)

QSTAG-416 ED.1 - Mechanized Infantry Operations - The Mechanized Infantry Battalion (Abca-416)

QSTAG-418 - Medium Girded Bridge Medium Grider Bridge Span Junction Equipment And Medium Grider Bridge Portable Pier Equipment

QSTAG-423 ED.2 - Levels Of Medical Support

The Armies of the United States, United Kingdom and Australia and the Canadian Forces have agreed to a concept of levels of medical support to be implemented within a wartime theatre of operations, in which members of two or more participating nations are deployed.

QSTAG-425 - Mask, Chemical-Biological, Field, M17A1 And Resuscitation Tube, Chemical-Biological Mask, M1

QSTAG-427 - Irritant Kit, (Uk), Smoke, Cs And (Us) Capsule, Cs (For Respirator Testing)

QSTAG-428 ED.2 - Howitzer, Medium, Self Propelled, 155Mm, M109 With Ammunition + Fire Control Equipment

QSTAG-429 ED.1 - Respiratory Resuscitation Equipment For Field Use (S/S By Qstag 677 Abca)

QSTAG-431 - Standardized List Of Abca Preferred Batteries

QSTAG-432 - Data Transmission Codes (Release To Other Than Dod Activities Requires Prior Approval Of Darcom) Abca 432

QSTAG-433 - Essential Performance Characteristics Of Field Surgical Lights (Abca-433)

QSTAG-434 - Patient & Operator Protection From Failure Of Electromedical Equipment (Abca 434)

This agreement includes the general patient and operator protection requirements for electromedical equipment additional to those which may be contained in other QSTAGS.

QSTAG-435 - Medical Materiel Management During Patient Evacuation

The Armies of the United States, United Kingdom and Australia and the Canadian Forces have agreed to methods of managing medical materiel used during the evacuation of patients within a wartime theater of operations in which members of two or more participating nations are deployed. The degree of standardization is complete.

QSTAG-436 - Minimum Labelling Requirements For Medical Material (Abc-436)

QSTAG-437 ED.1 - Surgical Instrument Set, Minor Surgery (Abca-437)

QSTAG-438 - Basic Range Of Electro Mechanical Pathology Equipment For Use In The Field

QSTAG-439 ED.1 - Minimum Medical Materiel For Cardiac Emergency (S/S By Qstag 677 Abca)

QSTAG-440 - Essential Characteristics Of Electro-Surgical Apparatus (Abca 440)

QSTAG-441 - Essential Characteristics Of Field X-Ray System

QSTAG-442 - Essential Characteristics Of Mobile & Portable Respirator/Ventilators (Abca 42)

QSTAG-444 - Essential Characteristics Of Mechanical Lung Ventilators (Abca-444)

QSTAG-446 ED.1 - Simulator Projectile, Airburst Liquid M9 (Spal)

The subject of this agreement is the Simulator Projectile, Airburst Liquid Chemical Agent L1A2, known as SPAL, which the US and AS Armies plan to purchase from the British Army.

QSTAG-447 - A Test Method For Method For Measuring Acoustical Noise (Abca-447)

This agreement establishes a test method for measuring steady state acoustical noise.

QSTAG-448 ED.1 - Comparison Of Abca Armies Ecm Standards (Abca 448)

QSTAG-449 ED.2 - A Glossary Of Terms Used In Sampling Inspection

QSTAG-451 - Shelter System, Collective Protection, Chemical Biological, Inflatable, Trailer Transported, M51 (Abca-451)

QSTAG-454 - Grenade, Discharger, Smoke Screening, L8A1 (Abca 454)

QSTAG-455 ED.1 - All Purpose Lightweight Individual Carrying Equipment (Release To Other Than Dod Agencies Must Be Approved By Hq Darcom (Drcird) (Abca 455)

QSTAG-456 - Grenade, Hand, Fragmentation, Delay, M67 And Grenade, Hand, Practice, Delay M69 (Abca-456)

The Armies of the United States and Australia and the Canadian Forces have agreed to standardize the Grenade, Hand, Fragmentation, Delay, M67 and the Grenade, Hand, Practice, Delay M69 as shown in the Details of Agreements, in order to achieve and maintain complete physical and functional interchangeability.

QSTAG-458 - Design Criteria For Crashworthiness (Light Fixed Wing & Rotary Wing Aircraft) Abca 458

This document establishes minimum crashworthiness design criteria which, when implemented in the initial stages of aircraft systems design, will provide the U.S. Army with aircraft which will possess improved crash safety characteristics.

QSTAG-46 ED.2 - Rifle, Recoilless, 106Mm: M40A2 With Ammunition

The 106mm Recoilless Rifle M40A2, with Ammunition, has been approved for use by the Armies of the United States and Australia and Canadian Forces as a solution to the immediate requirements for an infantry battalion anti-tank weapon.

QSTAG-460 - Goggles, Night Vision An/Pvs-5 (Abca 460)

The Armies of the United States, United Kingdom and Australia and the Canadian Forces have agreed to standardize design features of Night Vision Goggles used for Navigation Aid during hours of darkness in order to achieve functional and physical interchangeability.

QSTAG-461 ED.1 - Closed Circuit Refueling

The Armies of the United States, United Kingdom and Australia and the Canadian Forces have agreed to standardise on a Closed-Circuit Refuelling System (CCRS). This agreement is to provide completely functionally interchangeable CCRS fuelling nozzles and CCRS receivers.

QSTAG-462 - Decontaminating Kit, (Us) Skin, M258 (Uk) Decontaminating Kit, Personal (Dokp) (Ca) Mitt, Decontaminating, Cn Agent

The US Decontaminating Kit, Skin, M258, the UK Decontamination Kit, Personal (DKP), and the Canadian Mitt, Decontaminating, CE Agent have been approved by the Armies of the United States, United Kingdom and Canadian Forces as completely functionally interchangeable for use in reducing toxic hazard to skin when subjected to contamination by toxic chemical agents.

QSTAG-467 - Radio Set An/Prc-77 (Abca 467)

The Armies of the United States and Australia and the Canadian Forces have approved the Radio Set AN/PRC-25 for use in military operations requiring a short range, manpack portable, frequency-modulated (fm) reciever-transmitter to provide two-way voice communication in the frequency range 30.00 to 75.95 MHz.

QSTAG-468 - Image Intensifier Tube Assemblies 18 Millimeter Wafer & 25 Millimeter Inverter (Abca 468)

The Armies of the United States and Australia and the Canadian Forces have agreed to standardize design features of the 18mm and 25mm Image Intensifier Tube Assemblies used in night vision devices for observation and engagement of targets during the hours of darkness in order to achieve functional and physical interchangeability.

QSTAG-47 - Barge, Deck Cargo, Nonpropelled, Steel, Sectionalized, Nesting, 81-Foot, Design 7001 (Abca-47)

The Barge, Deck Cargo, Nonpropelled, Steel, Sectionalized, Nesting, 81-foot, Design 7001, is approved for use by the Armies of the United States and United Kingdom and Canadian Forces as an interim solution for a deck cargo barge intended for river and harbor transportation of tanks, vehicles, and other military material.

QSTAG-470 ED.1 - Documentation Relative To Medical Evacutation, Treatment And Cause Of Death Of Patients

The Armies of the United States, United Kingdom and Australia and the Canadian Forces have agreed to establish common procedures and standardised documents for reporting of patients initial first-aid treatment, en route identification and care, recording information concerning the patients of other nations and recording the medical cause of death.

QSTAG-471 - Supplementary Labels For Dispensed Medicine (Abca 471)

The Armies of the United States, United Kingdom and Australia and the Canadian Forces have agreed to use supplementary labels for dispensed medicines within a wartime theatre of operations in which member of two or more participating Armies are deployed.

QSTAG-475 ED.1 - A Manportable Short Range Anti-Tank Weapon

QSTAG-480 - Interoperability Of Tactical Digital Facsimile Equipment (Based Onnato Stanag 5000)

The aim of this agreement is to define the technical characteristics required to ensure the interoperability of tactical digital facsimile equipment.

QSTAG-481 - Color Code & Markings For Ammunition & Its Packaging

The aim of this Agreement is to adopt, for use by the NATO Forces, certain general rules to be followed for the marking of ammunition of a calibre below 20 mm, and its packaging, when the technical specifications of the ammunition are covered by a NATO standardization agreement.

QSTAG-486 ED.1 - Standardization Of Specification Requirements For Tachometer - Generators A. C. (Abca 486)

QSTAG-495 ED.2 - Riot Control And Training Agents

The Armies of the United States, United Kingdom and Australia and the Canadian Forces have approved Chemical Agents CS and CR as being functionally interchangeable for use as Riot Control Agents.

QSTAG-496 - Standards For Nbc Protective Mask & Canister Screw Threads

The threaded connection for the attachment of the canister of the NBC Protective Mask has been approved by the Armies of the United States, United Kingdom and Australia and the Canadian Forces, to allow physical interchangeability between the mask and canister.

QSTAG-499 - Test Procedures For Potassium Nitrate (Abca 499)

QSTAG-5 - Abca Armies Logistic Handbook (Abca)

QSTAG-500 - Test Procedures For Ethyl Centralite (Carbamite) (Abca 500)

The Armies of the United States, United Kingdom, Australia and the Canadian Forces have agreed to standardize identical test procedures for Ethyl Centralite as the standard reference test methods for determining specification requirements for this chemical in case of dispute.

QSTAG-501 ED.2 - Contaminated Or Dangerous Land Areas, Complete Equipments, Supplies & Stores, Warning Signs For The Marking Of(Abca Edition 2) (Based On Nato Stag 2002)

QSTAG-502 - Patrol Reports By Army Forces (Abca-502)

QSTAG-503 - Bombing, Shelling, Mortaring And Location Reports

QSTAG-504 - Bridge Classification Markings

QSTAG-505 - Target Grid Procedures

The Armies of the United States, United Kingdom and Australia and the Canadian Forces have implemented the provisions of STANAG No. 2011 entitled Target Grid Procedures.

QSTAG-506 ED.1 - Operation Orders, Warning Orders And Administrative/ Logistics Orders (Based On Stanag 2014)

The Armies of the United States United Kingdom and Australia and the Canadian Forces have agreed to implement the provisions of STANAG 2014 entitled "Operation Orders, Warning Orders and Administrative/Logistics Orders", the text of which is included under Details of Agreement.

QSTAG-507 ED.3 - Military Routes And Route/Road Networks

The aim of this agreement is to standardise the methods and procedures used on military routes and route/road networks by the Armies of the United States, United Kingdom, Australia, and the Canadian Forces.

QSTAG-508 ED.3 - Orders To The Demolition Guard Commander And Demolition Firing Party Commander (Based On Nato Stanag 2017)

The aim of this Agreement is to standardize the procedures to be used by the NATO Armed Forces for the issue of orders to the Demolition Guard Commander and to the Demolition Firing Party Commander in connection with the preparation, charging and firing of non-nuclear demolitions in operations on land.

QSTAG-509 - Military Symbols (Abca 509)

QSTAG-510 - Operational Situation Reports

QSTAG-511 - Intelligence Reports

QSTAG-512 - Marking Of Military Vehicles

QSTAG-513 - System For Field Wire Labelling Abca 513

QSTAG-514 ED.2 - Method Of Describing Ground Locations, Areas And Boundaries

QSTAG-515 - Proforma For Artillery Fire Plan (Based On Nato Stanag 2031)

The aim of this agreement is to standardize the proforma for the artillery fire plan for use by the ABCA Armies.

QSTAG-517 - Marking Of Headquarters And Dumps

QSTAG-520 - Operation Orders, Tables & Graphs For Road Movement (Based On Nato Stanag 2041) (Abca 520)

The aim of this Agreement is to standardize operation orders, tables and graphs for road movement.

QSTAG-523 - Procedures For Dealing With Prisoners Of War (Pw) (Amd. 1 Included)

The Armies of the United States, United Kingdom and Australia and the Canadian Forces have implemented STANAG No. 2044 entitled, Procedures for Dealing with Prisoners of War (PW) (the text of which is included under Details of Agreement).

QSTAG-529 ED.1 - Medical Employment Of Air Transport In The Forward Area

The aim of this Agreement is to standardise for the ABCA Forces the general principles governing evacuation by air transport of the sick and the wounded from the battle area.

QSTAG-530 - Reporting Engineering Information In The Field (Abca 530)

The aim of this Agreement is to standardize, for the use by the ABCA Forces, the format for reporting engineer information collected in the field.

QSTAG-532 - Markings For Umpires And Other Personnel, Vehicles And Installations During Combined Exercises

QSTAG-533 - Principles And Procedures For Establishing Liaison (Abca 533)

The aim of this agreement is to standardize the principles and procedures governing liaison between the ABCA Forces operating on land.

QSTAG-535 ED.1 - Medical Training In First Aid, Basic Hygiene And Emergency Care

The aim of this Agreement is to establish between ABCA Forces the minimum scope for the first-aid and basic hygiene training for non-medical personnel and to ensure that certain procedures for the training of qualified auxiliary medical personnel are standardised and can be carried out by the Armed Forces personnel of each ABCA nation concerned.

QSTAG-536 - Medical, Surgical And Dental Instruments, Equipment And Supplies (Abca 536)

QSTAG-538 - Recognition & Identification Of Forces On The Battlefield (Abca 538)

The aim of this agreement is to standardize, for use by the ABCA Forces, the procedures to be used for the recognition and identification of forces on the battlefield.

QSTAG-539 - Regulations For Military Motor Vehicle Movement By Road (Drc1Rd))

The aim of this agreement is to set out the basic regulations applying to military motor movement by road for the use of the ABCA Forces.

QSTAG-540 - Identification Of Movement Control & Traffic Control Personnel & Agencies (Abca 540)

The aim of this agreement is to standardize, for the use of the ABCA Forces, methods of identifying movement control and traffic control personnel and agencies.

QSTAG-541 - Standard Unit Of Vertical Measure To Be Shown On Land Maps (Based On Natd Stanag 2201) (Abca 541)

QSTAG-542 - Use Of Identical Maps By Abca Armed Forces Operating On Land (Based On Nato Stanag 2205

QSTAG-545 - Gazetteers (Based On Nato Stanag 2213) (Abca 545)

The aim of this agreement is to standardize the method of drafting Gazetteers for use by NATO Armed Forces.

QSTAG-547 - Vertical Aerial Cartographic, Photography (Based On Nato Stanag 2216) (Abca 547)

To standardize Vertical Aerial Cartographic Photography for use by Nato Armed Forces.

QSTAG-556 - Evaluation & Control Of Laser Hazards (Basedon Nato Stanag 3606)

The aim of this agreement is to establish the criteria for the evaluation and control of laser hazards.

QSTAG-56 ED.2 - Howitzer, Light, Towed, 105Mm, M101A1 With Ammunition And Fire Control Equipment (Abca-56)

The Armies of the United States , Canadian Forces and Australia have approved for use the Howitzer, Light, Towed, 105MM, M101A1 with Ammunition and Fire Control Equipment.

QSTAG-562 - Surface Transportation Request And Reply To Surface Transport Request

The aim of this Agreement is to standardize, for the use by the ABCA Forces, the information which units or formations must submit to the headquarters concerned (Movements and Transport Staff) when instructed to carry out a movement.

QSTAG-567 - Command And Control Of Infantry Battalion Antiarmor Weapons (Abca 567)

The Armies of the United States, United Kingdom, and Australia and the Canadian Forces agree to standardize the command and control procedures for employment of battalion anti-armor weapons described in the details of agreement in order to achieve interoperability of forces.

QSTAG-568 ED.1 - Command & Control Of Airmobile & Air Assault Operation (Abca 568)

QSTAG-57 ED.2 - Howitzer, Medium, Towed, 155Mm, M114A1 With Ammunition And Fire Control Equipment

The Howitzer, 155MM, M114A1 with Ammunition, and Fire Control Equipment has been approved for use by the United States and the Canadian Forces.

QSTAG-570 - Emplaning And Deplaning At The High Hover (Abca 570)

The Armies of the United States, United Kingdom and Australia and the Canadian Forces have agreed to standardize methods and procedures to be adopted when troops and cargo are to be lowered from or recovered to a helicopter at the high hover as described in the Details of Agreement in order to achieve interoperability of forces.

QSTAG-571 - Principles Governing The Design Of The Individual Load Carrying Equipment Of The Combat Soldier

QSTAG-572 - Lance, Field Artillery Missile System W/Ammunition & Fire Control Equipment Abca 572

QSTAG-573 ED.3 - Tactical Hand And Arm Signals For The Control Of Afvs

QSTAG-574 - Helicopter Blade Tracking Device (Abca 574)

QSTAG-577 - Machine Gun, Cal. .50, Browning M2 (Abca 577)

QSTAG-578 - Logistics Vocabulary For Abca Armies

The Armies of the United States, United Kingdom and Australia, and the Canadian Forces seek to achieve greater interoperability through standardization and mutual acceptance of common logistics terms and definitions.

QSTAG-579 ED.1 - Passive Viewer, Driver'S Night Vision

The Passive Viewer, Driver's Night Vision, hereinafter referred to as the viewer, is a passive viewing device that allows combat vehicles to be driven in a closed hatch configuration at low light levels without supplementary illumination.

QSTAG-580 - Medical Requirement For Blood & Blood Donors

The aim of this agreement is to protect blood donors as well as recipients, in case of cross-servicing between ABCA Forces, by introducing uniform medical requirements for blood donors.

QSTAG-581 - Radar, Ground Surveillance, Very Short Range

QSTAG-582 - Common Electrical Definitions & Terms Electrical Power Supplies (Abca 582)

QSTAG-583 - Quality Assurance Procedures For Demolition Stores, & Accessories (Abca 583)

This agreement has been approved for use by the Armies of the United States, United Kingdom, and Australia and the Canadian Forces as a standard for test procedures employed for Quality Assurance of Demolition Stores and Accessories.

QSTAG-585 - Procedures For Marshalling Helicopters In Airmobile Operations (Abca 585)

QSTAG-586 - Procedures To Be Employed In The Event Of Downed Helicopters Abca 586

QSTAG-59 ED.2 - Mortar, 81Mn, M29A1, Mount, Mortar, 81Mm, M23A1 With Ammunition And Sightunit M53A1

The Mortar, 81mm, M29A1; Mount, Mortar, 81mm, M23A1, with Ammunition and Sight unit, M53A1 have been approved for use by the United States and the Canadian Forces as a solution to the immediate requirements for an Infantry Battalion Medium Mortar.

QSTAG-590 - Marking Of Military Cargo For International Movement By All International Means Of Support

QSTAG-591 - Basic Military Road Traffic Regulations (Abca 591)

The aim of this Agreement is to standardize basic military road traffic regulations for ABCA Forces.

QSTAG-592 - Forecast Movement Requirements, Rail, Road And Inland Waterways (Abca 592)

The aim of this agreement is to standardize for ABCA Forces a document common to several means of transport for the purpose of submitting forecast movement requirements, including movement requirements based on approved contingency plans, to their own national authorities and/or to the nations concerned in such movements.

QSTAG-594 - Electrical Characteristics Of Digital Interface Circuits (Abca 594)

This standard specifies the electrical characteristics of the balanced voltage and the unbalanced voltage digital interface circuits, normally implemented in integrated circuit technology, that shall be employed for the interchange of serial binary signals between and among Data Terminal Equipments (DTE) and Data Communications Equipments (DCE) or in any interconnection of binary signals between voice or data equipments.

QSTAG-595 ED.2 - Glossary Of Telecommunication Terms

The Armies of the United States, United Kingdom and Australia, and the Canadian Forces have agreed to standardize the terms and definitions to be used in military communication system standards to insure interoperability and for clarity and unity of thought.

QSTAG-596 - Test Procedures For Tnt (Tolite) Abca 596

The Armies of the United States, United Kingdom, Australia and the Canadian Forces have approved QSTAG No 118 which accepts NATO STANAG No 4025 'Specification for TNT (Tolite)' for ABCA Armies' purposes.

QSTAG-597 - Handheld, Laser Rangefinder An/Gvs-5 (Abca 597)

The Armies of the United States and the United Kingdom and the Canadian Forces have agreed to standardize design features of the Handheld Laser Rangefinder AN/GVS-5, used to increase first-roung hit probabilities through fast and accurate range measurements, in order to achieve functional and physical interchangeability.

QSTAG-606 - Fuze, Proximity, Artillery, M732 (Abca 606)

The Army of the United States and Canadian Forces have approved the FUZE, PROXIMITY: Artillery, M732 for use in 4.2 inch mortar, 105mm howitzer, 175mm gun and 8 inch howitzer.

QSTAG-608 ED.3 - Interoperable Chemical Agent Detector Kits

The Armies of the United States, United Kingdom, and Australia, and the Canadian Forces, have agreed to accept the detection levels of the detector kits produced by each ABCA Country.

QSTAG-611 - Terrain Description Glossary (Abca 611)

The aim of this agreement is to foster collaboration between the ABCA member nations concerning studies of land combat, intervisibility, surveillance, target acquistion, mobility, radar masking, communications, navigation and engineer operations.

QSTAG-612 - Certification Of Magnetic Particle Inspection Personnel (Abca 612)

This agreement has been approved for use by the Armies of the United States, United Kingdom, and Australia, and the Canadian Forces to establish common criteria and compatible procedures for the qualification and certification of nondestructive testing personnel whose jobs require knowledge of the technical principles to process and inspect defense materials, parts and components by magnetic particle test methods.

QSTAG-62 - Wire Dispenser (Mx-306 A/G) (Abca-62)

The Wire Dispenser (MX-306 A/G) has been approved for use by the United States Army and the Canadian Forces as a solution to the immediate requirements for a high speed field wire dispenser.

QSTAG-622 - Essential Charisticstics Of Surgical Instruments (Abca 622)

QSTAG-623 ED.1 - Standard Method Of Writing Prescriptions For Spectacles

The aim of this Agreement is to achieve within ABCA Forces uniformity in the text of prescriptions for spectacles.

QSTAG-624 ED.1 - Medical Design Requirements For Military Pattern Ground Ambulances

The aim of this Agreement is to standardize certain design features of new motor ambulances to meet medical requirement so that patients of any nation can be carried in any military ambulance.

QSTAG-626 - Abca Armies Fuze Prodf Practices For Unguided Tube -Launched Projectiles (Abca 626)

The Armies of the United States, United Kingdom, and Australia, and the Canadian Forces have agreed to mutually accept national practices for Fuze Proof for Unguided Tube-Launched Projectiles.

QSTAG-627 ED.2 - Materials Handling In The Field

QSTAG-629 - Test Methods For Elastometer (Abca 629)

QSTAG-633 - Inspection And Quality Control Requirements For Industry (Abca 633)

The Armies of the United States, United Kingdom and Australia, and the Canadian Forces have agreed to use and standardize the application of Allied Quality Assurance Publication (AQAPs).

QSTAG-634 - Fluerics, Graphic Symbols To Be Used On Engineering Drawings And Documents

The Armies of the United States and Australia have agreed that the standard for graphic symbols for fluerics to be used on engineering drawings and documents will provide the necessary information for the interpretation and application as recorded in the Details of Agreement.

QSTAG-637 - Principles Of Medical Policy Of Mass Casualty Situation (Abca 637)

QSTAG-639 - Conditioned Dephase Modulation (Abca 639)

QSTAG-642 ED.2 - Codification Of Equipment - Uniform System Of Item Identification

The aim of this agreement is to provide a uniform system of item indentification for use by the Armed Forces of the ABCA countries.

QSTAG-644 - Radar Signal Detecting Set An/Apr-39(V)1 (Abca 644)

QSTAG-645 - Cross Servicing Of Helicopters Engaged In Land Operations

QSTAG-646 - Procedures Used In Establishing Ballistic Standard Ammunition (Abca 646)

QSTAG-647 - Procedure For The Transfer Of Standard Internal Ballistic Performance (Abca647)

QSTAG-653 - Standardization Of Wrench Openings (Si Metric Series)

QSTAG-655 ED.2 - Handling Of Deceased Personnel In An Area Of Operations

Standardize procedures for ABCA forces for handling of all deceased personnel in an area of operation.

QSTAG-657 - Guide Pecifications F Or Abca Army Fuels, Lubricants & Associated Products (Based On Stanag 2845)

The Armies of the United States, United Kingdom and Australia, and the Canadian Forces have agreed to adopt the provisions of STANAG 2845, Guide Specifications for NATO Army Fuels, Lubricants and Associated Products, the test of which is included under the Details of Agreement.

QSTAG-658 - Communication And Navigational Facilities For Multinational Airmobile Operations (Abca658)

QSTAG-66 ED.1 - Fuze, Blasting, Time, M700 (Abca-66)

QSTAG-660 - Movement Control

QSTAG-665 - Airmobile Operations (Abca 665)

QSTAG-666 - Wire Strike Protection System

QSTAG-669 - Aircraft Recognition Training (Abca 699)

QSTAG-670 - Standardization Of Proof Philosophies & Practices For Abca Guns, Mortars, Ammunition & Equipment Utilized At Proof Ranges (With Amendment 1 & 2)

The Armies of the United States, United Kingdom and Australia, and the Canadian Forces have agreed to standardize the broad Philosophies and Practices of Proof applicable as ABCA Guns, Mortars and Ammunition and Equipment Utilized at Proof Ranges.

QSTAG-672 - Night Vision Sight, Individual Served Weapon An/Pvs-4 (Abca 672)

QSTAG-674 - Message Text Formatting System (Formets) (Based On Nato Stanag 5500) (Abca 674)

QSTAG-675 - Data Information, Principles For The Automated Transfer Of, Between Tactical Command & Control Systems (Abca 675)

QSTAG-676 - Rules For Achieving Sub-Systems Interoperability Between The Automated Tactical Command & Control Systems Of Abca Armies (Abca 676)

QSTAG-677 ED.2 - Resuscitation Materiel For Field Use

The Armies of the United States, United Kingdom, Australia and the Canadian Forces have agreed to establish basic resuscitation materiel for medical care at all echelons.

QSTAG-680 ED.2 - Codification Of Equipment - Uniform System Of Supply Classification

The aim of this Agreement is to provide a uniform system of supply classification for use by the Armed Forces of the ABCA countries.

QSTAG-681 - Batteries, Non Rechargeable,Lithium

QSTAG-683 - Electric Power Conditioners,General Purpose

QSTAG-684 - Battery Chargers (Abca 684)

QSTAG-69 - Telephone Set Ta-43()/Pt, Telephone Set Ta-312()/Pt, And Telephone Set Ta-5003/U (Abca 69)

QSTAG-691 - Helicopter Tactical Refueling

QSTAG-693 - Principles & Characteristics Of Interoperability Security

QSTAG-699 - Aircraft Recognition Training (Abca 699)

QSTAG-7 - Financial Arrangements In Support Of Operations (Up To The Year 2000)

QSTAG-701 - Aircraft General Purpose Dispenser M-130

QSTAG-702 - Helicopter Infrared Hot Metal & Engine Plume Suppressor

QSTAG-715 - Battlefield Spectrum Management Hf (1.5-30 Mhz Band)

QSTAG-718 - Battlefield Spectrum Management Uhf (225-400 Mhz Band: (Abca 718)

QSTAG-719 - Battlefield Spectrum Management Tactical Radio Relay & Tropospheric Scatter Systems

QSTAG-721 - Battlefield Spectrum Management-Radar, Position Navigation, Tactical Sensor Systems & Multifunction Information Distribution Systems

QSTAG-724 - Calibration Of Ultrasonic Test Equipment With Standard Test Blocks

QSTAG-726 - Gun, 105Mm Field L118 & L119 With Associated Ammunition & Fire Control Equipment

QSTAG-733 ED.1 - Technical Standards For Single Channel High Frequency Radio Equipment (Based On Nato Stanag 4203)

QSTAG-742 ED.2 - Marking Of Hazardous Areas And Routes Through Them (Based On Nato Stanag 2889)

QSTAG-747 ED.2 - Nbc Survivability Acceptance Criteria, Design Guidelines, And Test Procedures For Defense Equipment

QSTAG-764 - Systeme International (Si) Unit For Combat Dosimetry

QSTAG-80 ED.1 - Chassis, Truck, 2 1/2 Ton, 6X6, M133, M207 And M210 Truck, Cargo, 2 1/2 Ton, 6X6, M135 And M211 Truck, Gasoline Tank, 2 1/2 Ton, 6X6, M217 Truck, Water Tank, 2 1/2 Ton, 6X6, M222 (Abca-80)

QSTAG-81 ED.1 - Trailers 1/4 Ton, 3/4 Ton, 1 1/2 Ton, 2 Wheel (Abca-81)

QSTAG-82 ED.1 - Chassis, Truck, 3/4 Ton, 4X4, M53 And M56, Truck, Cargo, 3/4 Ton, 4X4, M37 And Truck, Ambulance, 3/4 Ton, 4X4 M43 (Abca-82)

of the other ASCC countries, thus obtaining a cross-servicing facility without the need for prepositioning ground equipment.

AIR-STD-25/17 - Pressure Fuelling Replenishment Connection

The aim of this agreement is to standardize the pressure fuelling connections used in aircraft.

AIR-STD-25/18 - Connectors For 28 Volt Dc Servicing Power

To standardize the external DC Servicing Power Connections to the aircraft so that the external power supplies can be used to furnish electric power to the aircraft of any participating country.

AIR-STD-25/19 - Connectors For 115/200 Volt 400Hz 3-Phase Ac Servicing Power

AIR-STD-25/2 - Low Pressure Air And Associated Electrical Connections For Aero Engine Starting

AIR-STD-25/20 - Aircraft Electrical Systems Characteristics,

AIR-STD-25/21 - Ground Electrical Power Supplies For Aircraft

To provide common standards for ground source of electrical power for servicing of operational aircraft.

AIR-STD-25/24 - Ground Recharging Of Aircraft Main Batteries

To standardize the ground procedures for recharging aircraft main batteries to facilitate cross-servicing.

AIR-STD-25/25 - Electrical Safety Interconnections Between Aircraft, Support Equipment And Earth

To ensure that each member nation can interconnect aircraft and support equipment of other nations to ensure safety to life and equipment.

AIR-STD-25/26 - Earthing/Grounding Plug And Socket

AIR-STD-25/27 - Aircraft Liquid Oxygen Replenishment Connections

To standardize on the essential Mating Features of Ground Service Connectors for Liquid Oxygen, Supply Pressure and Hoses.

AIR-STD-25/28 - Compressed Nitrogen Characteristics, Supply, Pressure & Hoses For Oil Tolerant Use

To ensure that each member nation can service aircraft of the other member nations with nitrogen of acceptable purity for other than oxygen systems and at the required working pressure.

AIR-STD-25/29 - Compressed Air, Characteristics, Supply, Pressure & Hoses For Technical Purposes

To standardize compressed air characteristics, supply pressure and hoses.

AIR-STD-25/3 - Aircraft Servicing, Hazard, And Emergency Markings

To identify and standardize servicing, hazard, and emergency markings inside and outside aircraft used by member nations.

AIR-STD-25/30 - Breathing Oxygen Characteristics, Supply Pressure And Hoses

To ensure that each member nation can service aircraft of the other member nations with liquid or gaseous oxygen of acceptable purity for breathing and at the required working pressures.

AIR-STD-25/31 - Liquid Nitrogen Characteristics

To standardize Liquid Nitrogen Characteristics.

AIR-STD-25/32 - Cylinder Stored Compressed Air For Breathing Purposes (Req To Other Than Dod Act Req Pri Appr Of Hq Usaf/Xoxx-Iso Wash, Dc 20330-5058) (No S/S/Document)

To standardize characteristics of cylinder stored compressed breathing air.

AIR-STD-25/33 - Characteristics Of Supply Equipment For Liquid Nitrogen

To standardize on the essential mating feature of the aircraft external charging connector for liquid nitrogen, supply pressure and hoses.

AIR-STD-25/34 - Aircraft Gaseous Oxygen Replenishment Connections

AIR-STD-25/35 - Aircraft Gaseous Air/Nitrogen Replenishment Connections

The purpose of this agreement is to standardize on the mating and access clearance dimension of gaseous and non-breathable air replenishment connections for member nations?? aircraft.

AIR-STD-25/36 - Aircraft Compressed Air Replenishment Connections

AIR-STD-25/37 - Oil Free Compressed Nitrogen Characteristics, Supply Pressure & Hoses

To standardize characteristics of compressed oil free ntirogen, supply pressure and hoses.

AIR-STD-25/4 - Aircraft Fuelling

To establish standard for fuelling aircraft.

AIR-STD-25/5 - Lunette Eye Or Towing Ring

AIR-STD-25/6 - Aircraft Hydraulic System Servicing

To identify the basic requirement for hydraulic systems replenishment and activation to facilitate the cross-servicing of each member Nation's aircraft.

AIR-STD-25/9 - Aircraft Towing Attachments

AIR-STD-30/3 - Physical Interchange Of Digital Data

The purpose of this agreement is to ensure Member Nations can physically exchange digital form of engineering, maintenance and logistics data.

AIR-STD-30/5 - Interchange Of Digital Textual Data

AIR-STD-30/6 - Interchange Of Digital Raster Graphics

AIR-STD-30/7 - Interchange Of Digital Illustration Data

AIR-STD-44/10 - Data For Planning Air Movements

To standardize on the forms utilized in the planning and movements of troops and equipment in combined air transport operations.

AIR-STD-44/11 - Procedures For Coding, Tracing And Disposing Of Baggage

To adopt a standard of uniform coding of baggage items, to adopt a procedure for tracing missing baggage and to adopt a procedure for disposing of found baggage.

AIR-STD-44/12 - Restaint Factors For Fixed Wing Aircraft

To adopt as standard, factors for the restraint of air transported cargo and equipment in fixed wing transport (cargo) aircraft.

AIR-STD-44/13 - Drop Extraction Zones Visual Markings

AIR-STD-44/14 - Recovery And Release Of Parachutists Towed Behind Transport Aircraft

The purpose of this agreement is to standardize on procedure to release or retrieve parachutists towed behind transport aircraft.

AIR-STD-44/15 - Parachute Extraction Systems

AIR-STD-44/16 - Exchange Of Information - Transport Aircraft Loading Data

To authorize and establish procedures for exchange of transport aircraft load planning data.

AIR-STD-44/17 - Fixed Wing Cargo Aircraft Tie-Down Fittings

To adopt as standard the strength, dimensions and location of cargo floor tie-down fittings in fixed wing transport aircraft.

AIR-STD-44/18 - Responsibilities Of Air Transport Units, And Air Transported (User) Units For Air Movement In Combined Operations

AIR-STD-44/20 - Parachute Coupling Systems

AIR-STD-44/21 - Criteria For The Design Of Equip Required To Be Air Transported Orairdropped From Fixed Wing & Rotary Wing Transport Aircraft

AIR-STD-44/22 - Ground Handling Capabilities For Transport Aircraft (Exchange Of Information)

AIR-STD-44/23 - Division Of Responsibility Between Ground & Air Forces On Drop/Extraction Zones In Tactical Operations

To define the responsibility of the Airborne Force/Ground Force Commander and the Air Transport Force Commander with regard to the selection and marking of Drop/Extraction Zones.

AIR-STD-44/24 - General Rules Covering The Transport Of Loads By Helicopter

The purpose of this agreement is to define responsibilities and adopt standard helicopter cargo carrying procedures.

AIR-STD-44/25 - Transport Of Troops Byhelicopter

To adopt standard helicopter troop transport procedures.

AIR-STD-44/26 - Ultra Low Level Airdrop System Using Parachute Extraction

AIR-STD-44/27 - Airdrop Of Door Bundles With Sticks Of Parachutists

To adopt as standard a procedure for the airdrop of door bundles with sticks of parachutists.

AIR-STD-44/28 - Colours For The Identification Of Airdropped Supplies

To standardize a range of colours to be displaued on the outside surface of airdropped supplies, in order to enable their contents to be identified by ASCC forces, with minimum of delay.

AIR-STD-44/29 - Ready Access In Fixed Wing Transport Aircraft

To specify limits which will permit the passage of personnel past a load that has been lashed/restrained in a fixed wing transport aircraft.

AIR-STD-44/3 - Lashings For Fixed Wing Aircraft

AIR-STD-44/30 - Responsibility For The Design And Provision Of Adaptors Necessary To Achieve Compatibility Of Air Cargo Handling Equipment (With Amendment 1)

AIR-STD-44/31 - Tactical Refuelling Of Helicopters In Air Transport Operations

To standardize refuelling procedures for rotary wing aircraft in a tactical enviroment.

AIR-STD-44/32 - Technical Criteria For The Transport Of Cargo By Helicopter

To establish design criteria for the internal and external load equipment for air transport by helicopter and to ensure that national staffs consider these criteria in future design.

AIR-STD-44/33 - Helicopter Tactical Or Non-Permanent Landing Sites

To adopt standard dimensions and marking for helicopter landing sites for day and night operations.

AIR-STD-44/34 - Tactical Formation Flying By Helicopters In Air Transport Operations

The purpose of this agreement is to standardize procedures for day and night tactical helicopter formation flying.

AIR-STD-44/35 - Drop Zones And Extraction Zones: Criteria, Markings And Information Check Lists

To define the factors that require consideration when selecting and assessing the capacity of drop zones and to adopt a standard drop zone and extraction zone information checklists.

AIR-STD-44/36 - Aeromedical Evacuation By Helicopter

The purpose of this agreement is to standardize the procedures used in aeromedical evacuation by helicopter.

AIR-STD-44/37 - Criteria For Selection And Marking Of Landing Zones For Fixed Wing Aircraft

AIR-STD-44/38 - Wartime Air Movement Priorities System

The purose of this agreement is to provide a priority system to facilitate and assure the timely movement of airlift traffic within ASCC member nations.

AIR-STD-44/39 - Design Criteria For The 10,000 Lb (4,545 Kg) Air Transport Pallet

The purpose of this agreement is to establish design criteria for the 10,000 lb (4,545 Kg) air transport pallet.

AIR-STD-44/40 - Performance Criteria For Honeycomb Paper Used As Energy Dissipating Material

To adopt standard criteria to which honeycomb paper used as Energy Dissipating Material (EDM) must perform when used for aerial delivery tasks.

AIR-STD-44/41 - Combined Air Terminal Operations

To object of this agreement is to adopt the policy and procedures for the operation of a Combined Air Terminal.

AIR-STD-44/42 - Marshalling Signals For Fixed Wing & Rotary Wing Aircraft

To standardize marshalling signals for fixed wing and rotary wing aircraft by day and night.

AIR-STD-44/43 - Air Transport Baggage Tags

AIR-STD-44/44 - Helicopter External Cargo Hook Dimensions (Ch-1 2 Oct 1978)

AIR-STD-44/45 - Procedures For Tracing Air Baggage And Missing Air Cargo

To adopt a standardized procedure to trace lost or found air baggage, provide uniform descriptions of lost/found baggage, report air cargo delivery discrepancies, and to dispose of unclaimed baggage.

AIR-STD-44/46 - Load Preparation For External Carriage By Helicopters

AIR-STD-44/47 - Identification And Control Of Aircraft Pallets And Associated Restraint Equipment During Combined Airlift Operations (Sc-M)

AIR-STD-44/48 - Ground Security Procedures Against Hijacking Of Air Transport Aircraft

AIR-STD-44/49 - Movement, Handling And In Transit Storage Of Cargo Requiring Temperature Controlled Conditions

The purpose of the agreement is to standardize procedures for the air movement and in-transit storage of special cargo requiring controlled temperature conditions.

AIR-STD-44/50 - Emplaning And Deplaning At The High Hover

The purpose of this agreement is to standardize methods and procedures to be adopted when troops and cargo are to be inserted or extracted by helicopter at the high hover.

AIR-STD-44/52 - Transportation Of Troops On Aircraft Transporting Hazardous Cargo

AIR-STD-44/53 - Operational Carriage By Helicopter Of Ammunition & Fuel

To define responsibilities and adopt standard procedures for the Operational Carriage by Helicopter of Ammunition and Fuel.

AIR-STD-44/56 - Dimensional Features For Stretcher (Litter) Support & Retention By The Handles

AIR-STD-44/58 - Planning Procedures For Tactical Air Transport Operations

The purpose of this agreement is to define the factors that require consideration when selecting and assessing the capacity of landing zones, drop zones and extraction zone information checklists.

AIR-STD-44/59 - Floor Rails & Mating Equipment Attachment Pins

AIR-STD-44/60 - Cross Servicing Of Helicopters Engaged In Land Operations

The object of this agreement is to adopt standard procedures for cross-servicing of helicopters in multi-national land operations.

AIR-STD-44/62 - The Use Of Horse Collar (Strop) Type Helicopter Hosting Gear

AIR-STD-44/64 - Location Aids For Survivors Of Aircraft Accidents

The purpose of this agreement is to define the type and characteristics of aids to assist in the location of survivors or aircraft accidents.

AIR-STD-44/8 - System For Tracing Missing Cargo

To adopt a standard method of tracing missing cargo and correcting load discrepancies in the transportation of air cargo that will ensure delivery of cargo to consignee.

AIR-STD-44/9 - Handling And Documentation Of Dangerous Cargo For Air Transportation

To bring about increased standardization of procedures for the classification, labelling, marking, certification and documentation of dangerous cargo for movement on military aircraft.

AIR-STD-45/3 - Joint Air Operations Doctrine

To standardize the principles and planning considerations concerned in the employment of air power in tactical air operations.

AIR-STD-45/4 - Counter Air Operations

To standardize the tactical procedures to be used in the planning and execution of Counter Air Operations.

AIR-STD-45/5 - Tactical Air Procedures Offensive Air Support Operations

To standardize the tactical procedures to be used in the planning and execution of Offensive Air Support Operations.

AIR-STD-45/6 - Airspace Control In Times Of Crisis And War

To standardize the tactical procedures to be used in the planning and execution of Airspace Control in times of crisis and war.

AIR-STD-45/7 - Tactical Air Procedures Air Interdiction Operations

To standardize the tactical procedures to be used in the planning and execution of Interdiction Operations.

AIR-STD-45/8 - Tactical Air Procedures Tactical Air Support Of Amphibious Operations

To standardize the command and control procedures to be used by tactical air supporting amphibious operations.

AIR-STD-50/10 - Analogue Video Standard For Aircraft System Applications

To standardize on analogue video formats used in aircraft systems.

AIR-STD-50/2 - Digital Time Division Command/Response Multiplex Data Bus

AIR-STD-50/23 - Generic Open Architecture (Goa) Framework Standard

AIR-STD-50/3 - Sixteen Bit Computer Instruction Set Architecture - Chg. 1 Dtd 25 Fef 86 ( Req For Issue Other Than Dod Must Be Sent Via Hq Usaf/X/Xx (Iso) Wash Dc 20330-5058

To promote interoperability and reduce proliferation of software-incompatible processors in member nations by utilizing the same sixteen-bit instruction set architecture.

AIR-STD-50/5 - Standardization Of A Real Time High Order Computer Programming Language For Avionics Systems Application (Rel To Other Than Dod Act Req Pri Appr Of Hq Usaf/Xoxx, Wash Dc 20330-5058)

AIR-STD-50/7 - Discrete Signal Interfaces (Rel To Other Than Dod Act Req Pri Appr Of Hq Usaf/Xoxx, Wash Dc 20330-5058)

AIR-STD-51/1 - Helicopter Hoisting Gear, The Use Of Horse Collar (Strop) Type

To adopt a standard for a horse collor (rescue strap) type hoisting gear in order that all nations will be familiar with surivor pick-up equipment employed in rescue operations.

AIR-STD-51/12 - Characteristics Of Emergency Personnel Parachutes (Rel To Other Than Dod Act Req Pri Appr Of Hq Usaf/Xoxx(Iso), Wash Dc 20330-5058)

AIR-STD-51/2 - Emergency Markings

AIR-STD-51/3 - Search Pattern, Personal Locator Beacons

AIR-STD-51/4 - Standard Search Planning Data

AIR-STD-51/5 - Beacons, Personal Locator, General Characteristics Of

To incorporate in Personal Locator Beacons such common characteristics as will ensure their compatibility with the radio search equipment of member nations.

AIR-STD-51/6 - Characteristics Of Emergency Personnel Parachutes

To standardize the colour scheme of canopies of emergency personnel parachutes in order to facilitate location, identification and recovery of survivors by rescue forces of member nations.

AIR-STD-51/7 - Location Aids For Survivors Of Aircraft Accidents

AIR-STD-52/1 - Format Sizes For Air Cameras (Framing)

To adopt a standard range of air camera format sizes to permit the common use by all forces of air roll films, and processing, printing and other supporting equipments.

AIR-STD-52/10 - Sheet Photographic Paper For Air Photography

AIR-STD-52/11 - Dimensions, Tolerances, Characteristics And Core Sizes Rolled Photographic Paper For Air Photography

AIR-STD-52/13 - Calibration Certificate For Mapping Cameras

To establish a standard mapping calibration or performance certificate to facilitate maximum use of interchanged ASCC mapping photography by assuring the availability of essential metric data.

AIR-STD-52/14 - Dimensions, Tolerances And Characteristics Of 70Mm, 126Mm And 240Mm Rolled Film For Air Photography

AIR-STD-52/15 - Cores For 70 Mm Air Film

AIR-STD-52/16 - The Range Of Design Criteria And Functional Parameters For Low Altitude Photoflash Cartridges (To Be Reissued As Ascc Air Std 20/18)

AIR-STD-52/17 - Spools For 70 Mm, 126 Mm, And 240 Mm Rolled Air Film

AIR-STD-52/18 - Spacing Of 57 X 57Mm Exposures On 70Mm Perforated Film

AIR-STD-52/19 - Reconnaissance System Cross Servicing Information

AIR-STD-52/20 - Essential Data For Film Processing And Reconnaissance System Turn-Around

AIR-STD-52/21 - Target Pattern For Determination Of Aerial Photographic Resolution

AIR-STD-52/3 - Method Of Marking Pre-Packed Processing Chemicals For Black And White Negative And Positive (Air) Photographic Materials

AIR-STD-52/4 - Focal Lengths Of Lenses For Air Reconnaissance And Mapping Cameras

AIR-STD-52/5 - Black & White Air Film Developer High Contrast (Change 2 - 12 Jun 78)

AIR-STD-52/6 - Dimensions, Tolerances & Characteristics Of 16Mm & 35Mm Rolled Film For Aerial Cameras (Rel To Other Than Dod Act Req Pai Appr Of Hq Usaf/Xoxx (Iso) Wash, Dc 20330-5028)

AIR-STD-52/7 - Method Of Determining The Principal Sensitometric Characteristics Of Black And White Rolled Air Film

AIR-STD-53/1 - The Air Almanac

AIR-STD-53/10 - Standard Analogue Heading Outputs

AIR-STD-53/11 - The Specification For Evaluation Of The Accuracy Of Inertial Navigation Systems (Rel To Other Than Dod Act Req Pri Appr Of Hq Usaf/Xoxx(Iso), Wash Dc 20330-5058)

To adopt a standard method of determining the position accuracies of pure Intertial Navigation Systems.

AIR-STD-53/12 - The Specification And Evaluation Of The Accuracy Of Airborne Doppler Ground Velocity Sensors

To adopt a standard method of determining the accuracies of Airborne Doppler Ground Velocity Sensors.

AIR-STD-53/13 - The Specification For Evaluation Of The Accuracy Of Airborne Doppler Navigation Systems

AIR-STD-53/14 - Definition Of Sea State For Use In Connection With Doppler Navigation

AIR-STD-53/16 - The Specification For Evaluation Of The Accuracy Of Hybird Navigation Systems (Rel To Other Than Dod Act Req Pr Appr Of Cnm, Mat 09B21, Wash,D.C. 20360

AIR-STD-53/18 - Microwave Landing Systems (Mls) ( Relto Other Than Dod Act Req Pri Appr Of Hq Usaf/Xoxx(Iso), Wash Dc 20330-5058)

AIR-STD-53/2 - Sight Reduction Tables

To adopt standard celestial Sight Reduction Tables for Air Navigation.

AIR-STD-53/3 - The Proper Names Of 68 Stars

To adopt as standard the proper names of 68 stars used for air navigation.

AIR-STD-53/4 - Type Ms-28012-B6A Driftmeter

AIR-STD-53/5 - Minimum Operational Requirement (Mc) For Lightweight Doppler Systems For Fixed Wing Aircraft

AIR-STD-53/6 - True Airspeed Outputs

To adopt as standard, factors for True Airspeed Outputs.

AIR-STD-53/7 - Data Transmission For Radar Doppler Systems

To establish data transmission criteria for use in doppler radar systems.

AIR-STD-53/9 - Lightweight Doppler Navigation Equipment For Helicopters

AIR-STD-61/1 - Ejection Acceleration Limits

To establish guidelines to be used to assess the injury potential from acceleration imposed upon an aircraft crew member during powered emergency escape from a disabled aircraft.

AIR-STD-61/11 - Methodology For Cockpit Thermal Assessments

AIR-STD-61/12 - Methodology For Evaluation Of Anti Exposure Clothing In Cold Water Using Human Subjects (Issued Controlled)

AIR-STD-61/13 - Measurement Of Sound Attenuation Of Hearing Protective Equipment

To define methods of measuring the sound attenuation of hearing protective equipment.

AIR-STD-61/14 - The Measurement Of Protection Provided To The Respiratory Tract And Eyes Against Nbc Agents In Particulate, Aerosol And Vapor Form

AIR-STD-61/15 - Anthropometric Criteria For Litters Standards

AIR-STD-61/16 - Aviation Medicine/Physiological Training Of Aircrew

To define the minium requirements for initial and periodic aviation medicine/physiological training that shall be given to aircrew.

AIR-STD-61/2 - Restraint And Parachute Harnesses For Aircrew (S/S By Air-Std-61/102/2)

AIR-STD-61/20 - Method Of Partial Pressure Suit Evaluation For High Altitude Protection

To establish guidance as to the methods to be used for the evaluation of partial pressure assemblies to be worn by aircrew operation pressurized aircraft at altitudes above 50,000 feet (15,000m).

AIR-STD-61/21 - Physiological Requirements For Aircrew Oxygen Masks For Use At High Breathing Pressures

AIR-STD-61/22 - The Minimum Physiological Design Requirements For Aircrew Breathing Systems

AIR-STD-61/23 - Minimum Physiological Requirements For Aircrew Nbc Protective Headgear

To define the physiological requirements for aircrew NBC headgear assemblies which are designated to provide a protection factor which does not fall below 10. (See definition at para 8c).

AIR-STD-61/24 - Filter Blower Performance For Aircrew Nbc Headgear

To define the performance requirements to be met by blown filtered air supplied for positively ventilated aircrew NBC protective headgear.

AIR-STD-61/3 - Escape System Test Methods

This standard prescribes the principles and methods for yesys to be used to demostrate the performance of an escape system for a specific aircraft.

AIR-STD-61/32 - Interchangeability Of Aircrew Medical Categories

To establish the medical procedures for the exchange and assignment of aircrew among nations.

AIR-STD-61/33 - Evaluation Procedures For Flight Helmets

AIR-STD-61/39 - Maximum Permissble Temperatures Of Materials For Safe Contact With Bare Skin

AIR-STD-61/4 - Flotation And Sea Survival, Test Methods And Requirements

To standardize the requirements for inflatable life preservers.

AIR-STD-61/40 - A Technical Basis For Specifying The Insulation Of Immersion Protective Clothing

To standardize the technical basis upon which national guidelines to commanders may be drawn up in respect of the insulation requirements of immersion protective clothing.

AIR-STD-61/41 - Procedures For Calibration Of In-Flight Respiratory Data Acquisition Equipment

To define the procedures to be adopted for the calibration of equipment used in the acquisition of in-flight respiratory data.

AIR-STD-61/45 - Aviation Medicine/Physiological Training Of High Altitude Parachutists

To define the minimum aviation medicine/physiological training for high altitude parachutists.

AIR-STD-61/48 - Single Number Noise Reduction Of Hearing Protectors

The object of this AIR STD is to establish a method for calculating a single number moise reduction value to describe the overall performance of hearing protectors.

AIR-STD-61/5 - Escape Path Clearance In Ejection Seat Aircraft

AIR-STD-61/6 - Collection Of Data For Evaluation Of Helmets Damaged In Service (S/S By Air-Std-61/102)

To standardize the data collected from helmets damaged in service.

AIR-STD-61/7 - Minimal Protection For Aircrew Exposed To Altitudes Above 50,000 Feet

AIR-STD-61/73 - Minimum Standards For Breathing Equipment For Parachutists Between 13,000 & 25,000 Feet Pressure Altitude

AIR-STD-61/79 - Terminology Of Aeromedical Evacuation

AIR-STD-61/8 - Criteria For Reporting The Nature Of Clothing Materials On Assemblies Subjected To Physical & Operational Testing

AIR-STD-61/80 - Documentation Of Aeromedical Evacuation

AIR-STD-61/81 - Tests For Protective Capacity Of Fire Resistant Clothing Materials

AIR-STD-61/82 - Instrumentation For Escape System Thermal Hazard Analysis

AIR-STD-61/83 - A Basis For Common Practices And Goals In The Conduct Of Anthropometric Surveys

AIR-STD-61/84 - Initial Investigation And Immediate Management Of Laser Eye Injury In Aircrew

AIR-STD-61/9 - Protection Of Personnel Against The Effects Of High Levels Of Sound Upon Hearing & Operational Efficiency

AIR-STD-64/11 - Delineation Of Air Defense Identification Zones On Aeronautical Charts And Flight Information Publications

To ensure that Air Defense Identification Zones (ADIZ), when shown, are delineat4ed in the same manner on all aeronautical charts and Flight Information Publications.

AIR-STD-64/12 - Delineation Of The International Date Line On Aeronautical Charts And Flight Information Publications

To ensure that the placement of the International Date Line is the same on all aeronautical charts and Flight Information Publications.

AIR-STD-64/15 - Flight Information Publication, Enroute

To promote the standardization of Enroute Flight Information Publications produced by member nations to facilitate their use by any of the participating air forces.

AIR-STD-64/16 - Flight Information Publications - Planning

AIR-STD-64/18 - Title For Flight Information Publications

To standardize titles for Flight Information Publications (FLIP).

AIR-STD-64/19 - Explanatory Information Required On Aeronautical Charts

To identify the explanatory information to be shown on seronautical charts to satisfy the combined operational requirements of the member air force.

AIR-STD-64/20 - Operational Usage Criteria (S/S By Adv Pub 64/39)

AIR-STD-64/21 - Abbreviations And Code Legend Flight Information Publications 141166

AIR-STD-64/23 - Identification Of Scale On Aeronautical Charts

To enable participating air forces, by adoption of a common method, to identify without special instructions the scale of any aeronautical chart produced by any one of the air forces.

AIR-STD-64/24 - Symbols For Aeronautical Charts

To standardize the symbols used on aeronautical charts in order that air forces of one country may more easily use the aeronautical charts produced by participating nations.

AIR-STD-64/25 - Minium Content And Colour Of Aeronautical Information For Aeronautical Charts

AIR-STD-64/26 - Position Reference Systems For Aeronautical Charts

To identify a combined operational requirement to adopt basic position reference systems for use on aeronautical charts produced by participating nations.

AIR-STD-64/27 - Standard Scales For Topographic Aeronauticalcharts

To identify an operational requirement to adopt standard scales for topographic aeronautical charts produced by participating nations.

AIR-STD-64/28 - Definitions Of Aeronautical Map And Chart And Flight Information Terms

To establish a directory of terms and their definitions so that participating air forces may use without special instructions.

AIR-STD-64/29 - Aeronautical Chart Catalogues

AIR-STD-64/30 - Flight Information Publication Terminal

AIR-STD-64/31 - Identification Of Aerodrome By Name

To aid aircrew in the identification of aerodromes by the adoption of a common system for selecting the name under which the primary entry will appear in listings and on charts.

AIR-STD-64/32 - Aeronautical Chart Projections

AIR-STD-64/33 - Portrayal Of Navigation Grid Information

AIR-STD-64/34 - Identification Of Airspace Reservations (With Amendment 1)

AIR-STD-64/35 - Maximum Elevation Figure Criteria For Aeronautical Charts

To standardize the computation of Mximum Elevation Figures to be shown within the designated quadrangles on the aeronautical charts.

AIR-STD-64/36 - Aircraft Arresting Sysems, Information For Flips

To standardize the presentation of information related to aircraft arresting systems in enroute supplement and on instrument approach charts (terminal).

AIR-STD-64/37 - Flip Operational Abbreviations

To maintain a decode list of the operational abbreviations used in member nations' Flight Information Publications (FLIPS) and aeronautical charts.

AIR-STD-64/38 - Asw Dead Reckoning Tracker Plotting Charts

AIR-STD-64/6 - Standard Units Of Linear Measurement On Aeronautical Charts And Flight Information Publications (Req Other Than Dod Ref Hq Usaf/X0Xx-Iso, Washg., Dc 20330-5058 ( No S/S Document)

To identify standard units of linear measurement to be used on aeronautical charts and Flight Information Publications to satisfy the combined operational requirements of the member air forces.

AIR-STD-64/94 - Guidelines For The Assessment Of Thermal Stress In Aircraft Chemical Defense Operations

AIR-STD-65 - Changes To Ascc Air Standards/Advisory Publications - Working Party 65 - Airfield Marking & Lighting & Other Visual Aids

AIR-STD-65/1 - Lighting Of Instrument And Non-Instrument Runways

AIR-STD-65/10 - Airfield Lighting Control Systems

To standardize the airfield lighting control systems.

AIR-STD-65/11 - Illuminated Runway Distance Markers And Illuminated Hook Cable Markers

To achieve standardization between ASCC nations on Illuminated Runway Distance Markers (IRDM) and Illuminated Hookcable Marker (IHCM) as visual aids to aircraft operations at military airfields.

AIR-STD-65/12 - Airfield Lighting For Category 11 Operations

AIR-STD-65/13 - Extraneous Lighting In Vicinity Of Aerodromes

AIR-STD-65/14 - Airfield Marking And Lighting Color Standards

To establish standard colours for aeronautical ground light and surface markings.

AIR-STD-65/15 - Airfield Lighting Circuitry

AIR-STD-65/16 - Helipad Lighting (Vmc)

To establish a system of helipad lighting for Visual Meteorological Conditions (VMC).

AIR-STD-65/17 - Aerodrome Illuminated Markers And Signs

AIR-STD-65/18 - Apron Floodlighting

AIR-STD-65/19 - Standby Power Supply Requirements For Fixed Installations

AIR-STD-65/2 - Lighting Of Airfield Obstructions (Rel To Other Than Dod Act Req Pri Appr Of Hq Usaf/Xoxx-Iso Wash, Dc 20330-5058)

AIR-STD-65/21 - Helipad Marking

To standardize the markings of helipads at heliports, other than those heliports which use a runway for the helicopter landing area.

AIR-STD-65/22 - Airfield Clearance Planes

AIR-STD-65/23 - Aircraft Arresting Gears For Airfields

AIR-STD-65/24 - Air Traffic Control Procedures For Arrestment Of Aircraft

To ensure that each Member Nation using aircraft arresting systems of other Member Nations can expect Air Traffic Control to comply with a standard procedure.

AIR-STD-65/25 - Signals For Runway Party When Disengaging An Aircraft After A Hook Cable Arrestment

AIR-STD-65/26 - Pilots Operating Procedure For Engagement Of Airfield Arresting Systems (Issued Controlled)

The purpose of this ASCC AIR STD is to standardize pilot's procedure for engagement of airfield arresting systems.

AIR-STD-65/3 - Lighting And Marking Of Airfield Obstructions

To standardize the marking of airfield obstructions.

AIR-STD-65/30 - Pacific Nations Helicopter Operations From Ships Other Than Aircraft Carriers (Pac Hostac) Publications (Pac Hostac (Pac 1) And Pac Hostac Supplement (Pac 1-1)

To register national acceptance of PAC HOSTING (PAC 1) and PAC HOSTING Supplement (PAC 1-1).

AIR-STD-65/31 - Airfield Tone-Down Marking (S/S By Air-Std-65/36)

To standardize airfield tone-down markings.

AIR-STD-65/32 - Non-Tactical Heliport Lighting And Marking (Issued Controlled)

To establish heliport marking and lighting systems for visual meteorological conditions (VMC) and instrument meteorological (IMC) at heliports.

AIR-STD-65/33 - Airfield Declared Distances

To standardize the terminology and criteria for airfield declared distances.

AIR-STD-65/34 - Heliport And Helipad Lighting And Marking

The purpose of this agreement is to standardize lighting and marking of Heliports and Helipads.

AIR-STD-65/37 - Aircraft Arresting Systems Operating Procedures

AIR-STD-65/4 - Airfield Approach Lighting

AIR-STD-65/5 - Marking Of Instrument And Non-Instrument Runways (S/S By Air-Std-65/36)

AIR-STD-65/6 - Airfield Taxiway Markings (S/S By Air-Std-65/36)

AIR-STD-65/7 - Visual Glide Slope Indicator Systems

AIR-STD-65/8 - Airfield Portable Lighting Systems

AIR-STD-65/9 - Taxiway Lighting

AIR-STD-70/10 - Standard Analogue Heading Outputs

To establish scale factors and synchro voltages for the transmission of healing information.

AIR-STD-70/11 - The Specification For Evaluation Of The Accuracy Of Inertial Navigation Systems

To adopt a standard method of determining the position accuracies of pure Inertial Navigation Systems.

AIR-STD-70/13 - The Specification For Evaluation Of The Accuracy Of Airborne Doppler Navigation Systems

To adopt a standard method of determining the position accuracies of airborne doppler navigation systems.

AIR-STD-70/14 - Definition Of Sea State For Use In Connection With Doppler Navigation

AIR-STD-70/16 - The Specification For Evaluation Of The Accuracy Of Hybrid Navigation Systems

AIR-STD-70/17 - Definitions Of Aircraft Attitude And Heading Angles

The purpose of this agreement is to define the terminology used when referring to aircraft attitudes and manouevres.

AIR-STD-70/18 - Microwave Landing Systems (Mls)

AIR-STD-70/3 - Interoperability Of Aircraft Vhf Am And/Or Fm Multi-Frequency Transceiver Installations And Compatible Ground Radio Equipments

AIR-STD-70/4 - Interoperability Of Aircraft Uhf Multi-Frequency Transceiver Installation And Compatible Ground Transmitters And Receivers

AIR-STD-70/7 - Data Transmission For Radar Doppler Systems

To establish data transmission criteria for use in doppler radar systems.

AIR-STD-70/8 - True Airspeed Outputs

AIR-STD-80/1 - Method Of Determining The Principal Sensitometric Characteristics Of Black And White Rolled Air Film

AIR-STD-80/10 - Air Reconnaissance Request/Task Form

The purpose of this agreement is to standardize the format for requesting and tasking air reconnaissance by ASCC Armed Forces.

AIR-STD-80/11 - Titling Of Hand-Held Imagery (Wet)

AIR-STD-80/13 - Air Reconnaissance Intelligence Reporting Nomenclature

To standardize nomenclature for describing equipment and installations in imagery reports.

AIR-STD-80/14 - Point Designation Template For Imagery

To specify basic parameters to be observed in the construction of a universal grid for use in identifying a precise point of area on a frame of imagery.

AIR-STD-80/15 - Minimum Resolved Object Sizes For Imagery Interpretation

The purpose of this agreement is to specify minimum resolved object sizes required in imagery used for interpretation and technical analysis.

AIR-STD-80/18 - Reporting Of Data Used For Dimensional Analysis Of Imagery

The purpose of this agreement is to standardize the reporting of data used for dimensional analysis of imagery.

AIR-STD-80/3 - Dimensions, Tolerances And Characteristics Of 70Mm, 126Mm And 240Mm Rolled Film For Air Photography

To adopt standard dimensions, tolerances and characteristics for 70mm, 126mm, and 240mm rolled film for air photography, to permit the common use of film in cameras and processing equipment.

AIR-STD-80/5 - Target Pattern For Determination Of Aerial Photographic Resolution

The purpose of this agreement is to adopt a standard target pattern for determining the photographic resolution of aerial cameras used by ASCC nations during airborne operations.

AIR-STD-80/7 - Lm-230A/B Programmable Automatic Camera Test Set

AIR-STD-80/8 - Air Reconnaissance Intelligence Report Forms

To standardize and consolidate Air Reconnaissance Report Forms for reporting and presenting intelligence information derived from air reconnaissance and sensor imagery.

AIR-STD-84/11 - Casualty Handling In A Cw Environment

AIR-STD-84/12 - Peacetime Nuclear Weapons Accidents - Division Of Responsibilities

AIR-STD-84/13 - Peacetime Nuclear Weapons Accidents - Key Control Areas

AIR-STD-84/2 - Commander S Guide On The Effects Of Penetrating Ionizing Radiation (With Change 1)

To provide a standard method, within the ASCC member services, of categorizing the Radiation Exposure State of individuals, and groups of individuals, and to provide common guidance for Commanders.

AIR-STD-84/4 - First Aid Materiel For Chemical Injuries (With Change 1)

The purpose of this agreement is to standardize the minimum essential items of medical first-aid materiel for chemical injuries.

AIR-STD-84/9 - Nbc Defense Evaluation Of Air Bases

To identify the criteria for evaluating the effectiveness of Air Forces operating in an NBC environment.

AIR-STD-85/1 - Glossary Of Terms And Definitions

AIR-STD-90/4 - Aircraft Arresting Systems Information For Flips

The purpose of this agreement is to standardize the presentation of information related to aircraft arresting systems in enroute supplement and on instrument approach charts (terminal).

AIR-STD-94/3 - Comparative List Of Ascc Terms And Definitions For Nuclear Accident Response

To provide a comparative list of terms and definitions used by Member nations related to Nuclear Accident Response.

AOP-15 ED.3 - Guidance On The Assessment Of The Safety And Suitability For Service Of Non-Nuclear Munitions For Nato Armed Forces

AOP-16 ED.4 - Fuzing Systems: Guidelines For Stanag 4187

AOP-22 ED.1 - Design Criteria And Test Methods For Inductive Setting Of Electronic Projectile Fuzes

AOP-7 ED.2 - Manual Of Data Requirements And Tests For The Qualification Of Explosives Materials For Military Use

The primary objectives of this document are to promote standardization and interoperability of munitions among the NATO countries.

AOP-8 ED.2 - Nato Fuze Characteristics Catalogue

AQAP-100 ED.3 - Policy On An Integrated Systems Approach To Quality Through The Life Cycle

This document should be used, as a part of the overall policy of an organisation, to ensure quality of life cycle processes, products and services.

AQAP-11 - Nato Guideline For Specification Of Technical Publication

AQAP-110 ED.2 - Nato Quality Assurance Requirements For Design, Development And Production

AQAP-119 ED.2 - Nato Guide To Aqaps-110, -120, -130

AQAP-120 ED.2 - Nato Quality Assurance Requirements For Production

AQAP-130 ED.2 - Nato Quality Assurance Requirements For Inspection And Test

AQAP-131 ED.1 - Nato Quality Assurance Requirements For Final Inspection

AQAP-150 ED.2 - Nato Quality Assurance Requirements For Software Development Aqap-150

This publication specifies the project oriented requirements to manage the quality of the software development process.

AQAP-159 ED.2 - Guidance For The Use Of Aqap-150

This publication specifies the project oriented requirements to manage the quality of the software development process.

AQAP-170 ED.2 - Nato Guide For The Delegation Of Government Quality Assurance

AQAP-8 - Nato Guide To The Preparation Of Specifications For The Procurement Of Defence Material

ARMP-1 ED.4 - Nato Requirements For Reliability And Maintainability

ARMP-2 ED.2 - General Application Guidance On The Use Of Armp-1

ARMP-3 ED.2 - List And Source Of National And International Reliability And Maintenability Documents

ARMP-3 catalogues R&M Standards and other documents, military and civilian, which are produced by NATO countries.

ARMP-4 ED.4 - Guidance For Writing Nato R&M Requirements Documents

ARMP-6 ED.3 - Guidance For Managing In Service R & M

QAP-15 - Glossary Of Terms Usedin Proof (Rel To Other Than Dod Agencies Must Be Approved By Darcom, Drcde)

This QAP has been approved for use by the Armies of the United States, United Kingdom, and Australia and the Canadian Forces, as a Glossary of Terms used in Proof.

QAP-17 - Metallurical Terms & Definitions, Listing Of Glossaries Used By Armies (Req Other Than Dod Ref To Darcom, Drcde-1)

QAP-22 - Military Operations In Urban Terrain - Bibliography

QAP-9 - Engine Health Monitoring For Army Aircraft, Manual (Abca) (Release To Other Than Dod Requires Prior Approval Of Hq Darcom Drcird

QSTAG-101 ED.A - Standardization Of 2 Inch Fuze Holes And Fuze Contours For Artillery Projectiles 75Mm And Larger In Caliber Including 81Mm, 4. 2 Inches And 107Mm Mortars

QSTAG-105 - Sampling Procedures And Tables For Inspection By Attributes (Abca-105)

The Armies of the United States, United Kingdom and Australia and the Canadian Forces have standardized sampling procedures and tables for inspection by attrihutes.

QSTAG-108 ED.1 - Link, Cartridge, Metallic Belt 7.62Mm, M13 (Including Amendments 1 Thru 6)

QSTAG-109 ED.1 - Interchangeability Criteria For Batteries, Storage (Batteries, Secondary) (Lead - Acid Type)

QSTAG-111 ED.1 - U.S. Printing Press, Offset (Lithographic, Motor Driven, Mobile).And U.K. Machine Printing, Rotary, Lithographic, Offset, Two Colour (Abca-111)

QSTAG-112 - Water Purification Unit Van Body Mounted, Electric Motor-Driven, Erdlator-Type Clarifier, Diatomite Type Filters, 1500 Gph (Abca-112)

QSTAG-113 - Specification For Ce (Tetryl)-(Abca-113)

QSTAG-114 - Specification For Picrite (Nitroguanidine)-(Abca-114)

QSTAG-115 - Specification For Rdx (Hexogene)-(Abca-115)

QSTAG-116 - Specification For Petn (Penthrite)-(Abca-116)

QSTAG-117 - Specification For Ammonium Nitrate (For Use In Explosives)-(Abca-117)

QSTAG-118 - Specification For Tnt (Tolite) Abca-118

QSTAG-121 ED.1 - Rules Governing The Interchangeability Of Securing And Holding Devices For Infrared Scopes On Carbines, Rifles And Light Machine-Guns (Abca-121

QSTAG-122 ED.1 - Lamps For Tactical Vehicles (Abca-122)

QSTAG-123 ED.2 - Small Arms Ammunition (7.62Mm)

The subject of this agreement is functional interchangeability of 7.62mm ammunition.

QSTAG-125 ED.2 - Charger For Nato 7.62 Mm Ammunition (Based On Nato Stanag 2318) (Abca 125)

The subject of this agreement is functional interchangeability of the Charger for the 7.62MM Ammunition.

QSTAG-128 ED.1 - Interchangeability Of Infrared Equipment Mounted On Portable Infantry Weapons Optical Alignment Of The Telescope (Abca-128)

QSTAG-129 ED.2 - Standardization Of Inpact Tests For Steel For Guns (Based On Nato Stanag 4020) (Abca 129)

QSTAG-13 ED.2 - Immersion Requirement For Ground Role Service Equipment (Based On Nato Stanag 2842) (Abca) Edition 2

The aim of this agreement is to establish criteria for the immersion of applicable equipment used by the ABCA forces when operating in a ground role.

QSTAG-130 ED.1 - Nato Symbol Of Interchangeability (Abca-1

QSTAG-84 - Drill Rods And Bits For Hand-Held Air-Driven Rock Drills (Abca-84), With Amend. No 1

QSTAG-86 ED.3 - Barrel (Tube) 105Mm Tank Guns, M68, L.7A.1 And L.7A.3

QSTAG-88 - Floating Footbridge, Alumimum (Abca-88)

QSTAG-91 ED.2 - Boat, Reconnaissance, Pneumatic, 3 Man (Abca-91) With Edition No. 2

QSTAG-95 ED.1 - Fuze, Proximity, Artillery, M513 Series (Abca-95)

QSTAG-97 ED.4 - Standardization Of Wrench Opening (Inch Series)

STANAG-1001 ED.7 - Standardized System Of Designating Days And Hours In Relation To An Operation Or Exercise

STANAG-1005 ED.5 - Standard System Of Visual Markings For North Atlantic Treaty Naval Vessels

STANAG-1006 ED.4 - Preferred Incandescent And Fluorescent Electric Lamps For Lighting Purposes On Naval Vessels Of Nato Countries

STANAG-1007 ED.4 - Preferred Electric Lamps For Signaling Purposes On Naval Vessels Of Nato Countries

STANAG-1009 ED.4 - Standard Method Of Referring To Chapters, Pages, Articles, Etc. Of Documents And Publications

STANAG-1010 ED.4 - Specifications Of Water To Be Transferred To Ships Of Nato Navies Intented For Use In Boiler Feedwater Systems

STANAG-1022 ED.6 - Combat Charts, Amphibious Charts And Combat/Landing Charts

STANAG-1034 ED.19 - Allied Naval Fire Support - Atp-4 Edition F

STANAG-1040 ED.27 - Naval Cooperation And Guidance For Shipping (Ncags) Manual - Atp-2 Edition C Vol I

STANAG-1050 ED.3 - Distinctive Colour Of Clothing For Flight Deck Personnel

STANAG-1052 ED.35 - Allied Submarine And Anti-Submarine Exercise Manual - Axp-1(D)

STANAG-1057 ED.1 - Standard Method Of Passing Degaussing Information Between National Authorities (With Amendment 2 Thru 12)

STANAG-1059 ED.8 - Letter Codes For Geographical Entities

STANAG-1062 - Procedures For Services Rendered & Supplies Transferred To Visiting Nato Navies (Edition 4)

STANAG-1063 ED.21 - Allied Naval Communications Exercises - Axp-3 Edition D

STANAG-1065 ED.21 - Replenishment At Sea - Atp-16(D)/Mtp-16(D)

STANAG-1068 ED.26 - The Allied Maritime Above Water Warfare Exercise Manual - Axp-2 Edition D

STANAG-1074 ED.4 - Minimum Standard Characteristics Of Underwater Telephones For Use In Submarines, Surface Ships And Helicopters Of Nato Nations

The aim of this agreement is to establish the minimum standard characteristics of underwater telephones (UWT) for use in submarines, surfact ships and helicopters of NATO nations in order to allow communications between them and to receive transmissions from underwater distress or security beacons initiated by a submarine.

STANAG-1078 ED.2 - Standard Form Of A Naval Logistics Annex To Operation Orders

STANAG-1079 ED.4 - Diving Breathing Gases, Interchangeability Of Gas Cylinders & Compression Chambers & Provision Of Compression Chambers In Support Of Diving

STANAG-1080 ED.2 - North Atlantic Treaty Organization Fishing Permit

STANAG-1083 ED.4 - Tethered Submarine Marker Buoys

STANAG-1084 ED.5 - Replenishment Of Fuel In Harbour And Replenishment Of Water In Harbour And At Sea

STANAG-1095 ED.5 - Tie-Down Fittings On Shipborne Aircraft

STANAG-1100 ED.5 - Procedures For Visits To Nato And Non-Nato Ports By Naval Ships Of Nato Nations

STANAG-1103 ED.3 - Emergency Publication Of Nautical And Special Naval Charts

STANAG-1107 ED.3 - Action To Be Taken Upon Contact With Unidentified Submarines In Peacetime Nato Operations

STANAG-1110 ED.10 - Allowable Deterioration Limits For Nato Armed Forces Fuels, Lubricants And Associated Products

STANAG-1112 - General Specifications For Non-Sub Contact Charts

STANAG-1113 ED.4 - General Specifications For Projections Required For Nautical Charts For Polar Regions And The Higher Latitudes

The aim of this agreement is to standardize the general specifications for projections required for nautical charts, of polar regions and the higher latitudes, used by NATO Naval Forces.

STANAG-1119 ED.7 - Nuclear Fall Out Forecasting And Warning Organization Atp 25 (Navy) (Air)

STANAG-1120 ED.4 - Code Designation System For Special Naval Charts

STANAG-1123 - Compilation Data References On Special Naval Charts (With Amendments 1, 2, 3, 4)

STANAG-1132 ED.22 - Naval Mine Counter-Measures Tactics And Execution - Atp-24(C) Vol I

STANAG-1133 ED.3 - Nbc Defence Of Merchant Ships - Aep-3 (Navy)

The aim of this agreement is to register national acceptance of AEP-3 including Change 1.

STANAG-1135 ED.5 - Interchangeability Of Fuels, Lubricants And Associated Products Used By The Armed Forces Of The North Atlantic Treaty Nations

STANAG-1136 ED.3 - Standards For Use When Measuring And Reporting Radiated Noise Characteristics Of Surface Ships, Submarines, Helicopters, Etc. In Relation To Sonar Detection And Torpedo Acquisition Risk

STANAG-1137 ED.5 - Helicopter Naval Mine Countermeasures Manual - Amp-7 Edition D

STANAG-1138 ED.2 - Special Chart Folios For Merchant Ships

The aim of this agreement is to ensure that allied merchant ships which may be required to act in accordance with the Shipping Movement Policy contained in MC 12/6, will carry in peacetime sufficient charts to comply with this policy.

STANAG-1147 ED.3 - Interchangeability Of Mine Countermeasures Sweeping Gear And Equipment (Except Mcm Ammunition)

The aim of this agreement is to standardize the manufacture of float pendants and floats in order to facilitate interchangeability of minesweeping gear and parts.

STANAG-1149 ED.24 - Doctrine For Amphibious Operations - Atp-8 Edition C Volume I

STANAG-1150 ED.2 - Exchange Of Information About Helicopter Facilities In Ships Other Than Aircraft Carriers

The aim of this agreement is to establish a method of exchanging information relative to helicopter facilities in ships other than aircraft carriers.

STANAG-1152 ED.27 - Allied Antisubmarine Warfare Manual - Atp-28 Edition C

STANAG-1154 ED.12 - Nato Qualifications For Helicopter Controllers At Sea - Atp-78 Edition A

STANAG-1157 - Standard Symbols And Abbreviations For Use On Special Naval Charts

To standardize symbolization and abbreviations for nautical and special Naval Charts for use by NATO Nations.

STANAG-1162 ED.5 - Vertical Replenishment (Vertrep) Operating Area Marking, Clearances And Lighting

STANAG-1163 ED.6 - Nato Maritime Equipment Capabilities And Data - Atp-29(B)

STANAG-1166 ED.8 - Standard Ship Designator System - App-20 Edition A

STANAG-1167 ED.19 - Nato Above Water Warfare Manual - Atp-31 Edition C

STANAG-1173 ED.24 - Allied Maritime Tactical Instructions And Procedures - Atp-01 Vol I Edition F

STANAG-1174 ED.22 - Allied Maritime Tactical Signal And Manoeuvering Book - Atp-1 Edition F Vol Ii

STANAG-1175 ED.19 - Allied And Multinational Maritime Voice Reporting Procedures - App-1(C)/Mpp-1(C)

STANAG-1179 ED.2 - Combined Investigation Of Maritime Incidents

STANAG-1180 ED.10 - Amphibious Operations - Ship-To-Shore Movement - Atp-36(A)

The aim of this agreement is to register national acceptance of ATP-36(A) including Changes 1 and 2.

STANAG-1181 ED.11 - Supporting Arms In Amphibious Operations - Atp-37

The aim of this agreement is to register national acceptance of ATP-37 including Changes 1 through 10.

STANAG-1187 ED.2 - Management Of Hypothermia & Cold Injuries

STANAG-1192 ED.1 - Damage To Mcm Equipment As A Result Of Mine Explosion

STANAG-1194 ED.12 - Helicopter Operations From Ships Other Than Aircraft Carriers (Hostac) (Maritme Vstol Data Included) - Mpp-2 Edition G

STANAG-1200 ED.6 - Procedures For Logistic Support Between Nato Navies - Alp-1(E)

STANAG-1202 ED.2 - Nato Mine Countermeasures Vehicles And Equipment - Amp-3 Vol I

STANAG-1203 ED.4 - Underwater Signature Ranging Information Concerning North Atlantic Treaty Minesweepers And Minehunters- Amp-4(B)

STANAG-1209 ED.1 - Evaluation Of Maritime Quick-Don Survival Suits

STANAG-1212 ED.11 - Naval Cooperation And Guidance For Shipping (Ncags) - Organisation, Publications And Documents - Aap-8(F)

STANAG-1215 ED.1 - Management Of The Nearly Drowned

STANAG-1217 ED.3 - Standard Requirements For The Night Transfer Station Marker Box And/Or Wands

The aim of this agreement is to standardize the basic requirements for the night transfer station marker box, or the use of wands, to indicate the supplying ship's position stations, and the commodity to be transferred, during abeam replenishment at sea operations between NATO Navies.

STANAG-1218 ED.2 - Standard Reception Station Arrangements Designed To Support Up To 25O Kilogrammes (550 Pounds) Transfer Load

STANAG-1222 ED.1 - Single Probe Coupling

STANAG-1223 ED.2 - Standardization Of The Breakable Spool Coupling For Astern And Abeam Refuelling At Sea

STANAG-1226 - Therapeutic Recompression Tables & Pressure Units

STANAG-1229 ED.2 - Evacuation Of Diving Accident Patients

The aim of this agreement is to establish a procedure for the evacuation of a diving accident patient to a therapeutic centre (hyperbaric facility) equipped with a multiplace multicompartment hyperbaric chamber.

STANAG-1233 ED.1 - Procedures For Radhaz Control In Ports And Territorial Sea

STANAG-1235 ED.2 - Standard Requirements For The Use Of Day Transfer Station Markers And/Or Bats

The aim of this agreement is to standardize the basic requirement for the use of day transfer station markers or bats, to indicate the transfer and reception position stations and the type of commodity to be transferred during abeam replenishment-at-sea operations by NATO Navies.

STANAG-1236 ED.3 - Glide Slope Indicators For Helicopter Operations From Nato Ships

STANAG-1237 ED.1 - Inspection Of Aviation Facilities For Helicopter Operations From Ships Other Than Aircraft Carriers

The aim of this agreement is to establish minimum standard requirements for the inspection of shipboard aviation facilites in order to enable safe hepicopter operations to be conducted between ships of different NATO nations.

STANAG-1238 ED.4 - Use Of Commercial Or Military Submersibles For Submarine Rescue Work

The aim of this agreement is to provide assistance from military or commercial submersibles, or other assets, in the rescue of personnel from sunken submarines.

STANAG-1241 ED.5 - Nato Standard Identity Description Structure For Tactical Use

STANAG-1242 ED.18 - Naval Mine Warfare Principles - Atp-6(C) Vol I

STANAG-1243 ED.19 - Naval Mine Counter-Measures Operations, Planning And Evaluation - Atp-6(C) Vol Ii

STANAG-1244 ED.2 - Standardization Of Electronic Sound Underwater Signals

STANAG-1245 ED.2 - 40 Mm/L60 Gun Ammunition Interchangeable Within Nato Naval Forces

STANAG-1249 ED.1 - The Method Of Detection And Control Of Dysbaric Osteonecrosis In Divers

STANAG-1250 ED.1 - 100 Mm Gun Ammunition Interchangeable Within Nato Naval Forces

The aim of this Agreement is to: a. Provide a Catalogue of Weapons and Ammunition, commonly used by NATO Naval Forces which will show what ammunition, from a technical point of view, can be interchanged and fired effectively by each National weapons system. b. Record, where necessary, any additional data or clarifying information required for use in firing such ammunition. c. Explain the use of the interchangeability catalogue.

STANAG-1251 ED.2 - Shipboard Helicopter In-Flight Refueling (Hifr) Operating Area Marking, Clearances And Lighting

STANAG-1257 ED.4 - Nato Mine Delivery Systems - Amp-3(A) Volume Ii

STANAG-1258 ED.7 - Allied Maritime Structured Messages - App-4(A) Vol I

STANAG-1271 ED.1 - Standardization Of The Light Jackstay Outhaul Rope And Associated Blocks

STANAG-1274 ED.1 - Shipboard Haul Down Cable End Fitting For Helicopter Wire Recovery Assist Systems

STANAG-1275 ED.2 - Minimum Standard Requirements For The Marking And Lighting Of Helicopter Deck Landing Areas

STANAG-1277 ED.1 - Vertrep Equipment & Procedures

The aim of this agreement is to: a. Establish compatible VERTREP equipment attachment points, b. Document VERTREP equipment and procedures, to enhance interoperability during helicopter operations from ships other than aircraft carriers.

STANAG-1278 ED.2 - Standard For The Required Level And Measurement Of Coefficient Of Friction On Flight Decks

The aim of this agreement is to establish minimum standard requirements of coefficient of friction in order to reduce the possibility of aircraft sliding on flight decks.

STANAG-1280 ED.2 - Helicopter In Flight Refuelling (Hifr) Operating Requirements

STANAG-1283 ED.2 - 76 Mm/62 Gun Ammunition Interchangeable Within Nato Naval Forces

STANAG-1286 ED.1 - 5 Inch/38 Gun Ammunition Interchangeable Within Nato Naval Forces

STANAG-1289 ED.1 - Towing Link

STANAG-1296 ED.2 - Emergency Sonar Beacons To Aid The Detection And Localization Of Distressed Submarines (S/S By Stanag-1384)

STANAG-1297 ED.5 - Requirements For A Nato Common Rescue Seat

The aim of this agreement is to establish a common submarine rescue seat and identify the hold down devices used for rescue asset tiedown.

STANAG-1298 ED.4 - Minimum Requirements For The Provision Of Devices In A Distressed Submarine To Assist Location By Rescue Forces And Characteristics Of Submarine Marker Buoys

STANAG-1299 ED.2 - Emergency Sonar Beacons To Aid The Localization And Homing On To Distressed Submarines By Submerged Rescue Craft (S/S By Stanag-1384)

STANAG-1301 ED.5 - Minimum Conditions For Survival In A Distressed Submarine Prior To Escape Or Rescue

STANAG-1309 - Towing System

STANAG-1310 ED.6 - Design Criteria For Replenishment Aspects Of New Construction Naval Vessels

STANAG-1311 ED.3 - Nato Maritime Equipment Capabilities And Data - Atp-29 Supp 1(A)

STANAG-1312 ED.3 - Characteristics Of Nato Sea Mines - Amp-13 Vol Ii

STANAG-1313 ED.7 - Allied Naval Control Of Shipping Manual - Merchant Ship Reporting And Control (Merco) System - Atp-2 Vol I Supp 1

The aim of this agreement is to register national acceptance of ATP-2 Volume 1 Supplement 1, including Changes 1 through 5.

STANAG-1316 ED.6 - The Minewarfare Supplement To Nato Experimental Tactics And Amplifying Tactical Instructions - Axp-5(C) Mw Supp

STANAG-1318 ED.16 - Naval Co-Operation And Guidance For Shipping Manual (Ncags) - Guide To Owners, Operators, Masters And Officers - Atp-2(B) Vol Ii

STANAG-1319 ED.2 - Minimum Requirements For Medical Stores Located On Board Submarines In Support Of Escape/Rescue

The aim of this agreement is to standardize the minimum medical stores to be located in the escape compartments of submarines or to be dedicated to escape and/or rescue in the case of single compartment submarines with escape capability.

STANAG-1320 ED.4 - Minimum Requirements For Atmospheric Monitoring Equipment Located In Submarines With Escape Capability

The aim of this agreement is to define the minimum requirements for atmospheric monitoring equipment to be available in all submarine inhabitable compartments.

STANAG-1326 - Analysis Of Operational Utility Of Mine Warfare Studies

STANAG-1328 ED.1 - Standard Distance Line Lighting

The aim of this agreement is to standardize distance marker lighting during night replenishment at sea operations.

STANAG-1330 - Minimum Flight Deck & Hangar Helicopter Securing Arrangements, Spacing & Test Loads/Annulation

STANAG-1331 - Minimum Hangar Securing Arrangements, Spacing & Testing Criteria

STANAG-1336 ED.1 - The Nato Multi Service Electronic Warfare Support Group (Mewsg) Supplement To Axp-2

The aim of this agreement is to register national acceptance of MEWSG Supplement to AXP-2 and all changes thereto.

STANAG-1341 ED.1 - Harpoon Missile Interchangeable Within Nato Naval Forces

STANAG-1342 ED.1 - Mk-46 Torpedo Interchangeable Within Nato Naval Forces

STANAG-1343 ED.1 - Asroc System Interchangeable Within Nato Naval Forces

STANAG-1347 ED.1 - Seacat Missile Interchangeable Within Nato Naval Forces

STANAG-1355 - Silent And Darkened Shipborne Helicopter Procedures/Annulation

STANAG-1358 - Low Visibility Approach Pattern/Annulation

STANAG-1375 ED.1 - Microwave Landing Systems For Small Ship

STANAG-1382 ED.2 - Emergency Sonar Beacons To Aid The Detection And Localization Of Distressed Submarines And The Homing Onto Them Of Submerged Rescue Craft

STANAG-1384 ED.1 - Nato Standard Replenishment At Sea (Ras) Telephone Connectors

STANAG-1385 ED.6 - Guide Specification (Minimum Quality Standards) For Naval Distillate Fuels (F-75 And F-76)

STANAG-1391 ED.3 - Requirements Of A Distressed Submarine For The Receipt Of Emergency Life Support Stores (Elss) By Pod Posting

STANAG-1394 ED.1 - 20 Mm Ciws Phalanx Gun Ammunition Interchangeable Within Nato Naval Forces

The aim of this agreement is to provide a catalogue of weapons and ammunition, commonly used by NATO Naval forces which will show what ammunition, from a technical point of view, can be interchanged and fired by each national weapons system.

STANAG-1409 - Thermal Protection Guidelines

STANAG-1425 ED.2 - Guide Specification (Minimum Quality Standard) For Lubricating Oil,Steam Turbine And Gear Light Service (0-240 And 0-253)

STANAG-1427 ED.1 - Nato Standard Signalling Lamp For Merchant Ships

STANAG-2001 ED.2 - Medical First Aid Equipment And Supplies

STANAG-2002 ED.10 - Warning Signs For The Marking Of Nuclear, Biological And Chemical Contaminations

STANAG-2003 ED.6 - Patrol Reports

STANAG-2007 - Use Of Abbreviations By The Nato Armed Forces

STANAG-2008 ED.6 - Bombing, Shelling, Rocketing, Mortaring And Location Reports

The aim of this agreement is to standardize, for the use of the NATO forces, the method of rendering reports on enemy bombing, shelling, rocketing, mortaring and locations.

STANAG-2010 ED.6 - Military Load Classification Markings

The aim of this agreement is to standardise the method of marking the military load classification of bridges and rafts and the corresponding marking of vehicles.

STANAG-2011 ED.4 - Adjustment Of Artillery Fire

STANAG-2012 - Military Route Signing (Edition No. 3) (With Amendments 1 Thru 4)

STANAG-2014 ED.9 - Formats For Orders And Designation Of Timings, Locations And Boundaries

STANAG-2015 ED.3 - Route Classification

STANAG-2017 ED.4 - Orders To The Demolition Guard Commander And Demolition Firing Party Commander (Non-Nuclear)

The aim of this agreement is to standardize the procedures to be followed by the Authorized Commander for the issue of orders to the Demolition Guard Commander and the Demolition Firing Party Commander conducting the planning, preparation, charging and/or firing of non nuclear demolitions on land.

STANAG-2019 ED.6 - Nato Joint Military Symbology - App-6(C)

STANAG-2022 ED.8 - Intelligence Reports

STANAG-2023 ED.2 - Marking Of Military Cargo For International Movement By All International Mean Ranspoot

The aim of this agreement is to standardize, for the use of the NATO Forces: Marking of military cargo and Handling and Storage Instructions, for consignments of military cargo, for international movement by all international means of transport, except where the move is national in character and is handled exclusively by that nation's means of transport.

STANAG-2024 ED.5 - Military Road Traffic Lighting Regulations

STANAG-2025 ED.6 - Basic Military Road Traffic Regulations

The aim of this agreement is to standardize basic military road traffic regulations for NATO forces.

STANAG-2026 ED.4 - Nato Travel Order

The aim of this agreement is to standardise the system for field cable or field wire labelling used by the NATO Armed Forces.

STANAG-2027 ED.3 - Marking Of Military Vehicles

The aim of this Agreement is to standardize the marking of military vehicles for the use of NATO forces.

STANAG-2028 ED.4 - System For Field Cable Or Field Wire Labelling

The aim of this agreement is to standardize the system for field cable or field wire labelling used by the NATO Armed Forces.

STANAG-2029 ED.7 - Method Of Describing Ground Locations, Areas And Boundaries

STANAG-2031 ED.5 - Proforma For Artillery Fire Plan

STANAG-2033 ED.6 - Interrogation Of Prisoners Of War (Pw)

STANAG-2034 ED.7 - Nato Standard Procedures For Mutual Logistic Assistance

STANAG-2035 ED.6 - Signing Of Headquarters And Installations

STANAG-2037 ED.8 - Vaccination Of Nato Forces

STANAG-2040 ED.6 - Stretchers, Bearing Brackets And Attachment Supports

STANAG-2041 ED.4 - Operation Orders, Tables & Graphs For Road Movement

The aim of this egreement is to standardize operation orders, tables and graphs for road movement.

STANAG-2042 ED.2 - Method Of Challenging By Guards And Sentries

STANAG-2043 ED.3 - Principle And Procedures For Establishing Communications

STANAG-2044 ED.5 - Procedures For Dealing With Prisoners Of War (Pw)

STANAG-2047 ED.9 - Emergency Alarms Of Hazard Or Attack (Cbrn And Air Attack Only) - Atp-85 Edition A

STANAG-2048 ED.4 - Chemical Methods Of Insect And Rodent Control - Amedp-3(B)

STANAG-2050 ED.5 - Statistical Classification Of Diseases, Injuries And Causes Of Death

STANAG-2060 ED.2 - Identification Of Medical Material For Field Medical Installations

The aim of this agreement is to facilitate rapid identification of medical material containers used in field medical installations to enable more effective cooperation between NATO Forces.

STANAG-2061 ED.5 - Procedures For Disposition Of Allied Patients By Medical Installations

STANAG-2066 ED.5 - Layout For Military Correspondence

The aim of this agreement is to standardize for use within NATO the layout of military correspondence and the rules for the use of abbreviations and acronyms.

STANAG-2067 ED.5 - Control And Return Of Stragglers

The aim of this agreement is to specify standard policies and procedures with regard to the handling of stragglers from the forces of one NATO nation by the forces of another.

STANAG-2068 ED.5 - Emergency War Surgery

The aim of this agreement is to: a. Standardize the general principles of the initial care of war-wounded and provide standard medical measures. b. Provide a guide for the medical services which may be used by all NATO and PfP forces.

STANAG-2070 ED.4 - Emergency War Burial Procedures

The aim of this agreement is to standardise the procedures to be used when the forces of one NATO nation perform emergency burials on land for the dead of another NATO nation, the enemy and non-combatants as necessary.

STANAG-2077 ED.7 - Intelligence Records

STANAG-2079 ED.4 - Rear Area Security

The aim of this agreement is to provide, for use by the NATO Forces, a system for rear area security and rear area damage control within a theatre of operations, by standardizing.

STANAG-2082 ED.6 - Relief Of Combat Troops

STANAG-2083 ED.7 - Commanders' Guide On The Effects From Nuclear Radiation Exposure During War

STANAG-2084 ED.6 - Handling And Reporting Of Captured Equipment And Documents

The aim of this agreement is to standardize the procedures to be used by the NATO Forces for the handling of and reporting on captured equipment and documents.

STANAG-2085 ED.4 - Nato Combined Military Police

STANAG-2087 ED.6 - Medical Employment Of Air Transport In The Forward Area

STANAG-2088 ED.5 - Battlefield Illumination

The aim of this agreement is to standardize the doctrine and procedures for the control of battlefield illumination and the methods and techniques of its application by NATO forces.

STANAG-2096 ED.4 - Reporting Engineer Information In The Field (Includes Amendment 1)

STANAG-2097 ED.6 - Nomenclature And Classification Of Equipment

The aim of this agreement is to standardize the procedures to be used when establishing the nomenclature and classification of equipment in order to facilitate the electronic and manual exchange of intelligence data between databases in accordance with formats agreed upon in AIntP-3.

STANAG-2099 ED.3 - Fire Coordination In Support Of Land Forces

The aim of this Agreement is to standardize, for the use of the NATO Armed Forces, procedures for fire coordination in support of land forces.

STANAG-2101 ED.11 - Establishing Liaison

STANAG-2103 ED.11 - Warning And Reporting And Hazard Prediction Of Chemical, Biological, Radiological And Nuclear Incidents (Operators Manual) - Atp-45 Edition E

STANAG-2104 ED.9 - Friendly Nuclear Strike Warning (Strikwarn)

This agreement provides the policy, guidance, and direction for all participating NATO Forces in tactical situations involving warning of friendly nuclear strikes.

STANAG-2109 ED.6 - Postal Organization And Courier Service For The Nato Forces

The aim of this agreement is to achieve secure, speedy, efficient and interoperable postal and courier services in the NATO Forces.

STANAG-2111 ED.4 - Target Analysis - Nuclear Weapons

The aim of this agreement is to standardize for the use of the NATO Forces, the terminology and procedures to be used in analyzing targets for attack by nuclear weapons.

STANAG-2112 ED.5 - Nuclear, Biological And Chemical Reconnaissance

The aim of this agreement is to standardize the definitions of terms associated with NBC reconnaissance and survey.

STANAG-2113 ED.6 - Denial Of A Unit'S Military Equipment And Supplies To An Enemy

The aim of this agreement is to state agreed policy on the denial in wartime of a unit's military equipment and supplies to an enemy.

STANAG-2115 ED.4 - Fuel Consumption Unit

The aim of this agreement is to standardize, for the use of the NATO Forces when engaged in land operation.

STANAG-2116 ED.6 - Nato Codes For Grades Of Military Personnel

STANAG-2117 ED.2 - Methods Of Assessing Enemy Logistical Movement And Transport Capabilities (Includes Amendment 1)

The object of this Agreement is to standardize, for the use of the NATO Armed Forces, the basis for assessing enemy logistical, movement and transport capabilities.

STANAG-2118 ED.2 - Intelligence Estimate

STANAG-2121 ED.4 - Cross-Servicing Of Medical Gas Cylinders - Amedp-53 Edition A

STANAG-2122 ED.3 - Requirement For Training In First-Aid, Emergency Care In Combat Situations And Basic Hygiene For All Military Personnel

STANAG-2123 ED.2 - Obstacle Folder

The aim of this agreement is to standardize the procedures to be used by NATO nations in connection with the preparation in peacetime of pre-planned, pre-constructed and/or field-type obstacles.

STANAG-2126 ED.6 - First-Aid Dressings, First Aid Kits And Emergency Medical Care Kits

STANAG-2127 ED.3 - Medical, Surgical And Dental Instruments, Equipment And Supplies

STANAG-2128 ED.4 - Medical And Dental Supply Procedures

The aim of this agreement is to facilitate the necessary cross-servicing amongst the Medical Services of the NATO Forces.

STANAG-2129 ED.8 - Identification Of Land Forces On The Battlefield And In An Area Of Operation

STANAG-2130 ED.1 - Employment Of Atomic Demolition Munitions (Adm) (Includes Amendments 1 Thru 3)

STANAG-2131 ED.4 - Multilingual Phrase Book For Use By The Nato Medical Services - Amedp-5(B)

The aim of this agreement is to reister national acceptance of AMedP-5(B).

STANAG-2132 ED.3 - Documentation Relative To Initial Medical Treatment And Evacuation - Amedp-8.1 Edition A

STANAG-2133 ED.2 - Vulnerability Analysis Of Chemical And Biological Hazards

STANAG-2134 ED.2 - Defensive Air Support Operation

STANAG-2135 ED.3 - Technical Data For Handling Custodial Nuclear Weapons (Includes Amendments 1 Thru 4)

The aim of this Agreement is to establish procedures for effecting emergency logistic assistance in a period of tension or in war, to the forces of NATO nations, international headquarters, or multinational formations.

STANAG-2136 ED.5 - Minimum Standards Of Water Potability During Field Operations - Amedp-18

STANAG-2139 ED.2 - Atomic Demolition Munitions (Adm) Operations Order

The aim of this agreement is to standardize the procedures to be used by the NATO Forces for the issue of ADM Operation Orders in connection with the preparation, charging and firing of ADMs in operations on land in accordance with current nuclear operations plans and US and national custodial procedures.

STANAG-2143 ED.5 - Explosive Ordnance Reconnaissance/ Explosive Ordnance Disposal (Eor/Eod)

The aim of this agreement is to provide the foundation for standardization in the field of Explosive Ordnance Reconnaissance/Explosive Ordnance Disposal (EOR/EOD).

STANAG-2144 - Call For Fire Procedures

The aim of this agreement is to standardize, for the use of the NATO Armed Forces, a procedure to be used when Artillery observers call for fire from firing units.

STANAG-2146 ED.2 - Co-Operation - Infantry/Armoured Fighting Vehicles

The aim of the agreement is to standardize, for the use of NATO Forces the procedures to be adopted prior to infantry-armoured fighting vehicle (AFV) operations.

STANAG-2147 ED.4 - Target Numbering System

The aim of this agreement is to standardize a basic system for target numbering to be used in fire support operations by the NATO forces.

STANAG-2149 ED.6 - Request For Information

The aim of this agreement is to standardize the method by which military authorities and forces of NATO nations and NATO commands pass Requests For Information to and from one another.

STANAG-2150 ED.7 - Nato Standards Of Proficiency For Nbc Defence

STANAG-2151 ED.2 - Route Network-Definitions And Characteristics (With Amendments 1 And 2)

STANAG-2152 ED.5 - Loading Ramps

The aim of this agreement is to standardize the method to be used by the NATO Forces for erecting loading ramps using railway sleepers and for the utilization of these ramps to load and unload all types of military vehicles onto flat wagons.

STANAG-2153 - Parallel Marking Of Special Flat Wagons And Heavy Military Vehicles With Amendments 1, 2 And 3 (S/S By Nato Stanag 2175)

The object of this Agreement is to define the parallel markings to be placed on heavy military vehicles and on special flat wagons, used by the NATO Armed Forces stationed in Continental Western Europe.

STANAG-2154 ED.6 - Regulations For Military Motor Vehicle Movement By Road

The aim of this agreement is to set out the basic regulations applying to military motor movement by road for the use of the NATO Forces.

STANAG-2155 ED.2 - Road Movement Bid & Credit (Includes Amendment 1 & 2)

The aim of this agreement is to provide participating nations with standardized documents (see paragraph 5 below) for road movement in a format suitable for automatic data processing (ADP) and/or manual handling, applicable in peace and in wartime in all NATO Forces.

STANAG-2156 ED.4 - Surface Transport Request And Surface Transport Reply

The aim of this agreement is to standardize the data which forces must submit to the responsible agencies of another nation from which they request surface transport (Surface Transport Request).

STANAG-2158 ED.4 - Identification Of Military Trains

The aim of this agreement is to standardize the procedures for the identification of military trains used by the NATO forces moving within the territories of NATO nations of continential Europe.

STANAG-2159 ED.4 - Identification Of Movement Control And Traffic Control, Personnel And Agencies

The aim of this Agreement is to standardize, for the use of the NATO Forces, methods of identifying movement control and traffic control personnel and agencies.

STANAG-2163 ED.3 - Vehicle Weight And Dimension Card

The aim of this Agreement is to adopt for the use of the NATO Armed Forces a standard card to facilitate the load planning and loading operations of whatever means of transport is to be used.

STANAG-2164 - Advice Of Movement (Issue Controlled-Private Industry Submit Request Via Cognizant Contracting Office For Certification Of Need To Know)

STANAG-2165 ED.3 - Forecast Movement Requirements - Rail, Road And Inland Waterways

The aim of this agreement is to standardize for NATO Forces and document common to several means of transport for the purpose of submitting forecast movement requirements, including movement requirements based on approved contingency plans, to their own national authorities and/or to the nations concerned in such movements.

STANAG-2166 ED.3 - Movement & Transport Documents Used For Movements By Ship

The aim of this agreement is to standardize the essential movements and transport documents used for the movement of materials by ship to and from NATO nations so that loading and discharge can be carried out efficiently.

STANAG-2171 ED.6 - Procedures For Military Trains Crossing Frontiers

The aim of this agreement is for NATO Armed Forces to standardize in both peacetime and wartime.

STANAG-2172 - Classification And Marking Of Ordinary Flat Wagons Used For The Transport Of Military Vehicles (Use Nato Stanag 2175)

The object of this Agreement is to define the categories of ordinary flat wagons to be used by the NATO Armed Forces stationed in Continental Western Europe for the transport by rail of their light and medium-weight vehicles.

STANAG-2173 ED.4 - Regulations For The Securing Of Military Tracked And Wheeled Vehicles On Railway Wagons

The aim of this agreement is to standardize within NATO Forces the regulations concerning the securing of military tracked and wheeled vehicles on railway wagons in frontier crossing exchange traffic.

STANAG-2174 ED.4 - Military Routes And Route/Road Network

The aim of this agreement is to standardize the method and procedures used on military routes and route/road networks by the NATO Forces.

STANAG-2175 ED.3 - Classification And Designation Of Flat Wagons Suitable For Transporting Military Equipment

The aim of this agreement is to facilitate the preparation and execution of military transport.

STANAG-2176 ED.1 - Procedures For Military Road Movement Across National Frontiers

The aim of this Agreement is to standardize the regulations, procedures and forms for military road movements and trasport across frontiers between the NATO nations.

STANAG-2201 ED.3 - Standard Unit Of Vertical Measure To Be Shown On Land Maps

STANAG-2202 ED.3 - Map Conventional Signs

To ensure that conventional signs on standard topographical maps produced by the North Atlantic Treaty Nations are easily understood by any of the NATO Armed Forces without extra training and without any danger of misinterpretation.

STANAG-2205 ED.4 - Use Of Identical Maps And Charts (Excluding Nautical Charts)

The aim of this agreement is to ensure that all forces allocated to NATO operating together use identical maps, charts, and other geographic materials in order to achieve interoperablility, coordination of action and safety of friendly troops.

STANAG-2208 ED.3 - Place Name Spelling On Maps And Charts

The object of this agreement is to standardize the method of spelling place names in the mapping and charting of areas of interest to NATO, to ensure that no confusion can arise on this account between the NATO Armed Forces.

STANAG-2210 ED.4 - Trig Lists (Lists Of Geodetic Data)

The aim of this agreement is to standardize the trig lists prepared for use by the NATO Armed Forces.

STANAG-2211 ED.6 - Geodetic Datums, Projections, Grids And Grid References

STANAG-2212 - Map Series Numbering

STANAG-2216 ED.4 - Vertical Aerial Cartographic Photography

STANAG-2217 - Sizes Of Indexes To Series Of Land Maps

STANAG-2219 ED.1 - Medical Preventive And Protective Measures Associated With Missile Operations

The aim of this agreement is to identify the elements necessary for developing minimum preventive and protective measures associated with missile operations in NATO.

STANAG-2225 ED.5 - Technical Data For Handling Custodial Nuclear Weapons

STANAG-2251 ED.6 - Scope And Presentation Of Military Geographic Information And Documentation (Mgid)

STANAG-2253 ED.5 - Mgd - Roads And Road Structures

The aim of this Agreement is to ensure that nations, when producing Military Geographic Documentation (MGD) on Roads and Road Structures for use by NATO Forces, standardize its presentation in accordance with this STANAG. The Agreement also gives guidance on the associated Military Geographic Information (MGI) required.

STANAG-2254 ED.4 - Mgd - Navigable Inland Waterways

STANAG-2255 ED.5 - Mgd - Ports

The aim of this agreement is to ensure that nations, when producing Military Geographic Documentation (MGD) on Sea Ports, and where applicable, Major Inland Waterway Ports, for use by NATO Forces, standardize its presentation in accordance with this STANAG. This agreement also gives guidance on the associated Military Geographic Information (MGI) required.

STANAG-2256 ED.4 - Mgd - Inland Hydrography

STANAG-2257 ED.4 - Mgd - Railways

STANAG-2259 ED.4 - Mgd - Terrain

STANAG-2260 ED.3 - Mgd - Electric Power

STANAG-2263 ED.4 - Mgd - Coastal Areas And Landing Beaches

STANAG-2269 ED.3 - Mgd - Engineer Resources

STANAG-2271 ED.3 - Mgd - Urban Areas

STANAG-2275 ED.2 - Indexes To Military Geographic Information And Documentation (Mgid), Use Natostanag 3672

The object of this Agreement is to standardize the presentation of Indexes to Military Geographic Information and Documentation (MGID) to ensure that such Indexes provide NATO Nations and Commands with essential and easily understandable information on the availability of MGID suitable for planning and operational purposes.

STANAG-2315 ED.3 - Symbol To Denote The Operational Interchange Ability Of Ammunition & Demonolition Accessories (Short Title, Nato Symbol Of Interchangeability)

The aim of this Agreement is to adopt a symbol for use by the NATO Forces to denote that certain ammunition or certain demolition accessories are operationally interchangeable.

STANAG-2316 ED.4 - Marking Of Ammunition (And Its Packaging) Of A Calibre Below 20 Mm

The aim of this Agreement is to adopt, for use by the NATO Forces, certain general rules to be followed for the marking of ammunition of a calibre below 20 mm, and its packaging, when the technical specifications of the amjunition are covered by a NATO standardization agreement.

STANAG-2318 ED.2 - Charger For Nato 7.62Mm Ammunition

The object of this agreement is to standardize features of the chargers for NATO 7.62mm Ammunition designed in accordance with STANAG 2310, necessary to ensure physical interchangeability between weapons of the NATO Armed Forces.

STANAG-2320 ED.3 - Mark Nato Design

STANAG-2321 ED.4 - The Nato Code Of Colours For The Identification Of Ammunition (Except Ammunition Of A Calibre Below 20 Mm)

The aim of this agreement is to standardize on a colour code which wil serve to identify the use, effect produced and hazard potential of ammunition (except ammunition of a calibre below 20 mm) used by NATO Forces.

STANAG-2322 ED.2 - Minimum Markings For The Identification Of Ammunition (And Its Packaging)

The aim of this Agreement is to standardize within the NATO Forces minimum markings which shall be applied to ammunition and its packaging (except those items listed in paragraph 3 of this STANAG) manufactured by or for the NATO Nations after the date of promulgation of this STANAG.

STANAG-2329 ED.2 - Links For Disintegrating Belts For Use With Nato 7.62Mm Cartridges

The aim of this agreement is to standardize, for the use of the NATO Armed Forces, the characteristics of links for disintegrating belts for use with NATO 7.62 mm cartridges as prescribed in STANAG 2310.

STANAG-2333 ED.4 - Performance And Protective Properties Of Combat Clothing

The aim of this agreement is to establish guidelines for the requirements and properties of combat clothing for use by NATO Forces in the land environment.

STANAG-2335 ED.2 - Interchangeability Of Combat Clothing Sizes

The aim of this agreement is to establish between the NATO Forces a sizing system of new equivalents in combat clothing, to facilitate interchangeability between them.

STANAG-2336 ED.1 - Trials Of Camouflage Material

STANAG-2342 ED.2 - Minimum Essential Medical Equipment And Supplies For Military Ambulances At All Levels

STANAG-2345 ED.3 - Evaluation And Control Of Personnel Exposure To Radio-Frequency Fields -3Khz To 300 Ghz

STANAG-2346 ED.2 - Standard Method Of Writing Prescriptions For Spectacles

STANAG-2347 ED.2 - Medical Warning Tag

STANAG-2348 ED.3 - Basic Military Hospital (Clinical) Records

STANAG-2350 ED.3 - Morphia Dosage And Casualty Markings

The aim of the agreement is to standardise within the NATO Forces the range of initial dose of morphia to be administered to combat casualties, and the method of marking the event.

STANAG-2351 ED.2 - Procedures For Marshalling Helicopters In Multinational Land Operations

The aim of this ageement is to standardize procedures for the NATO Forces to be used by marshallers/guides directing ground movements of helicopters in multinational land operations.

STANAG-2352 ED.6 - Chemical, Biological, Radiological And Nuclear (Cbrn) Defence Equipment ?√ Operational Guidelines

STANAG-2353 ED.5 - Evaluation Of Nbc Defence Capability

STANAG-2354 ED.2 - Medical Requirements For Blood And Blood Donors

STANAG-2355 ED.3 - Procedure For The Employment Of Helicopters In The Anti Armour Role

The aim of this agreement is to standardize procedures to be followed by NATO forces when employing helicopters in an anti-armour role.

STANAG-2356 ED.2 - Comparative Formation/Unit Designations

The aim of this agreement is to standardize a table of comparative formation/unit designations for the use by NATO Forces.

STANAG-2357 ED.3 - X-Ray, Film Formats, Cassettes And Screens

STANAG-2358 ED.4 - First Aid And Hygiene Training In A Cbrn Or Tih Environment

STANAG-2361 ED.2 - Minimum Essential Medical Supply Items In Theatres Of Operations

STANAG-2363 ED.2 - Security Doctrine -Aintp-2(A)

The aim of this agreement is to register nation acceptance of AINTP-2(A).

STANAG-2366 ED.1 - Stopping Power Of Land Minefields

The aim of this agreement is to standardize the procedure for identifying the effectiveness of land minefields.

STANAG-2367 ED.6 - Nato Glossary Of Cbrn Terms And Definitions - Aap-21(B)

STANAG-2368 ED.1 - Guide For The Restoration Of Facilities On The Lines Of Communications, Ports And Other Critical Installations After Hostile Actions - Aap-18

The aim of this agreement is to register national acceptance of AAP-18.

STANAG-2369 ED.3 - The Nato Eod Publications Set (Neps) ┬Û Identification And Disposal Of Surface, Air, And Underwater Munitions

STANAG-2370 ED.2 - Interservice Improvised Explosive Device Disposal Operations On Multinational Deployments - A Guide For Staff Officers / Operators ?√ Aeodp-3(B) Vol I & Vol Ii

STANAG-2373 ED.1 - Survey Accuracy Requirements For Surface To Surface Artillery

The aim of this agreement is to standardize the method of expressing the Artillery Survey Accuracy criteria for weapons, target acquisition, surveillance and meteorological systems in current use by nations and to establish a common understanding of the criteria used by nations in order to facilitate mutual survey support.

STANAG-2374 ED.2 - Method Of Application Of A Standard Marking System For The Identification Of Propelling Charges

The aim of this agreement is to standardize the mehtod of applying the marking which will identify for the user, the propelling charges for gun, howitzer and mortar annumition.

STANAG-2375 ED.1 - Battlefield Vehicle Recovery And Evacuation Guide - Aep-13

STANAG-2391 ED.2 - Explosive Ordnance Disposal Recovery Operations On Fixed Installations - Aeodp-5(A)

STANAG-2394 ED.3 - Land Force Combat Engineer Doctrine - Atp-52(B)

STANAG-2398 ED.1 - Friendly Chemical Attack Warning

STANAG-2400 ED.2 - Battlefield Vehicle Recovery - Users Handbook - Aep-17(A)

The aim of this agreement is to register national acceptance of AEP-17 (A).

STANAG-2404 ED.1 - Joint Anti-Armour Operations

STANAG-2406 ED.6 - Land Forces Logistic Doctrine - Alp-4.2(A)

STANAG-2410 ED.1 - List Of Nato Civil/Military Ground Engine Lubricating Oil Interchangeability

STANAG-2411 ED.1 - Shape Comments

STANAG-2412 ED.1 - The Effects Of Wearing Individual Protection Equipment On Individual And Unit Performance During Exercises - Axp-8

STANAG-2418 ED.2 - Policy For Expedient Repair, Including Battle Damage Repair

STANAG-2424 ED.1 - Nbc Contamination Control Policy For Nato Air Forces/Annulation

STANAG-2429 ED.3 - Personnel Identification While In Nbc Individual Protective Equipment (Ipe)

STANAG-2442 ED.1 - Nato Standardization Of Colour Coding And Marking Of Experimental Test Ammunition

The aim of this agreement is to establish within NATO a uniform method for colour coding and marking experimental test ammunition.

STANAG-2443 ED.1 - Use Of The Ace Reporting System

STANAG-2500 ED.4 - Nato Handbook On The Medical Aspects Of Nbc Defensive Operations - Amedp-6(B)

STANAG-2601 ED.3 - Standardization Of Electrical Systems In Tactical Land Vehicles

STANAG-2604 ED.3 - Braking Systems Between Tractors, Draw-Bar Trailer And Semi-Trailer Equipment Combinations For Military Use

STANAG-2754 ED.9 - Fuels To Be Introduced Into And Delivered By The Central European Pipeline System (Ceps)

STANAG-2761 ED.2 - Equipment For Receipt And Delivery Of Liquid Fuels

STANAG-2764 ED.4 - Fuels To Be Introduced Into And Delivered By The North European Pipeline System (Neps)

The aim of this Agreement is to designate the grades of fuel to be introducted into and delivered by the North European Pipeline System (NEPS). Define the qualities of fuels entering the NEPS and its outlets. Quality characteristics given herein my vary from those given in guide specifications to compensate for pipeline operations.

STANAG-2805 ED.5 - Fording And Flotation Requirements For Combat And Support Ground Vehicles

STANAG-2814 ED.4 - Field Artillery Sighting Systems

STANAG-2816 - Maintenance Requirements For Mechanical Equipment For Armies

STANAG-2817 ED.3 - Design And Constructional Requirements Which Facilitate Maintenance Of Electrical And Electronic Equipment For Armies

STANAG-2818 ED.2 - Demolition Materiel: Design, Testing And Assessments

The aim of this agreement is to standardize the following, for new demolition materiel to be used for NATO armed forces: a. design principles and criteria for safety and suitability for service (AOP-31), and b. methods for testing and assessment of safety and suitability for service (AOP-32).

STANAG-2826 - Characteristics Of Unit Loads And Corresponding Handling Equipment - Annex C - Military Containers( And )Appendix 2 To Annex D - Basic Dimensions Of Pallet Trucks (With Amendments 1 Thru 3)

STANAG-2827 ED.6 - Materials Handling In The Field

STANAG-2828 ED.6 - Military Pallets, Packages And Containers

STANAG-2829 ED.4 - Materials Handling Equipment

STANAG-2830 ED.5 - Material Handling Aids

STANAG-2831 - Climatic Environmental Conditions Affecting The Design Of Material For Use By Nato

The aim of this agreement is to describe the principal climatic factors which constitute the distinctive climatic environments found throughout the world, excluding Antarctica, and to establish for each climatic factor, levels of intensity to which the NATO forces require their materiel to remain safe and be capable of acceptable performance.

STANAG-2832 ED.3 - Dimensional Restrictions For The Transport Of Military Equipment By Rail On European Railways

The aim of this agreement is to facilitate the movement of trains carrying military equipment on the railway networks of Belgium, Denmark, France, Germany, Italy, Luxembourg and the Netherlands.

STANAG-2833 ED.1 - Counter Surveillance Requirements In Equipment Design

STANAG-2836 ED.3 - Removable Paints For Camouflage

STANAG-2837 ED.1 - Evaluation Of Stopping Power Of Land Minefields

STANAG-2838 - 105 Mm Howitzer Ammunition Interchangeable Within Nato Land Forces In Emergency, In War

The aim of this agreement is to provide a catalogue of 105 mm Howitzer Ammunition and weapons, commonly used by NATO Land Forces, which will show what ammunition can be interchanged and fired by each national weapon system in emergency in war.

STANAG-2839 - 155 Mm Howitzer, 175 Mm Gun And 8 Inch Howitzer Ammunition (Including Primers And Fuzes) Interchangeable Within Nato Land Forces In Emergency, In War

The aim of this agreement is to provide catalogues of 155 mm How, 175 mm Gun and 8 inch Howitzer ammunition (including primers and fuzes) and weapons, commonly used by NATO forces, which will show what ammunition can be interchanged and fired by each national weapon system in emergency in war.

STANAG-2840 - 105Mm Tank Gun Ammunition Interchangeable Within Nato Land Forces, In Emergency, In War

The aim of this agreement is to provide a catalogue of 105 mm Tank Gun ammunition and weapons, commonly used by NATO Land Forces, which will show what ammunition can be interchanged and fired by each national weapon system in emergency in war.

STANAG-2842 - Immersion Requirements For Ground Role Service Equipment

STANAG-2845 ED.3 - Guide Specifications For Nato Army Fuels, Lubricants And Associated Products (Includes Amendments 1 & 2)

The aim of this agreement is to provide guide specifications which establish the minimum quality of fuels, lubricants and associated products used in ground service operations by NATO Forces.

STANAG-2848 - 106Mm Recoiless Rifle Ammunition Interchangeable Within Nato Land Forces, In Emergency, In War

The aim of this agreement is to provide a catalogue of 106 mm Recoiless Rifle and Calibre 50 Spotter-tracer ammunition and weapons, commonly used by NATO Land Forces, which will show what ammunition can be interchanged and fired by each national weapon system in emergency in war.

STANAG-2849 - 90Mm Tank Gun Ammunition Interchangeable Within Nato Land Forces, In Emergency, In War

The aim of this agreement is to provide a catalogue of 90 mm Tank Gun ammunition and weapons, commonly used by NATO Land Forces, which will show what ammunition can be interchanged and fired by each national weapon system in emergency, in war.

STANAG-2850 - 4.2 Inch Motar Ammunition Interchangeable Within Nato Land Forces, In Emergency, In War

The aim of this agreement is to provide a catalogue of 4.2 inch Mortar ammunition and weapons, commonly used by NATO Land Forces, which will show what ammunition can be interchanged and fired by each national weapon system in emergency, in war.

STANAG-2851 - 81 Mm Mortar Ammunition Interchangeable Within Nato Land Forces, In Emergency, In War

The aim of this agreement is to provide a catalogue of 81 mm mortar ammunition and weapons, commonly used by NATO Land Forces, which will show what ammunition can be interchanged and fired by each national weapon system in emergency, in war.

STANAG-2855 - 20 Mm Hispano Suiza/M139 (20 Mm X 139) Ammunition Interchangeable Within Nato Land Forces, In Emergency, In War

The aim of this agreement is to provide a catalogue of 20 mm Hispano Suiza/M139 (20 mm x 139) ammunition and weapons, commonly used by NATO land forces, which will show what ammunition can be interchanged and fired by each national weapon system in emergency, in war.

STANAG-2856 - 20 Mm M168(Vulcan) And M61 (20 Mm X 102) Ammunition Interchangeable Within Nato To Land Forces, In Emergency, In War

The aim of this agreement is to provide a catalogue of 20 mm M168 (VULCAN) and M61 (20 mm x 102) ammunition and weapons, commonly used by NATO land forces, which will show what ammunition can be interchanged as to safe firing by each national weapon system in war.

STANAG-2861 ED.2 - Procedures In The Event Of Downed Helicopters (Includes Amendments 1 Thru 3)

The aim of this agreement is to standardize the immediate action and priorities in the event of a downed helicopter during an operational mission.

STANAG-2863 ED.5 - Navigational & Communication Capabilities For Helicopters In Multi- National Land Operations

The aim of this agreement is to standardize the minimum navigational communication capabilities necessary for helicopters in multinational land operations.

STANAG-2865 ED.1 - Recording Of Data For Artillery Survey Control Points (Includes Amendments 1 Thru 6)

The aim of this agreement is to standardize which data is to be recorded for artillery survey control points and the proforma to be used by NATO Forces.

STANAG-2866 ED.3 - Medical Effects Of Ionizing Radiation On Personnel

The aim of this agreement is to provide information for use by medical officers in advising field commanders on the medical effects of nuclear radiation on NATO forces.

STANAG-2867 ED.2 - Radiotelephone Procedures For The Conduct Of Artillery Fire

The aim of this agreement is to standardize, for the use of the NATO forces, a radiotelephone procedure to be used between artillery observers and artillery fire direction centres when calling for fire.

STANAG-2868 ED.5 - Land Force Tactical Doctrine - Atp-35(B)

The aim of this agreement is to register national acceptance of ATP-35(B) including change 1.

STANAG-2870 - Determination Of Cholinesterase Activity

STANAG-2871 ED.4 - First-Aid Materiel For Chemical Injuries

STANAG-2872 ED.3 - Medical Design Requirements For Military Motor Ambulances

The aim of this agreement is to standardize certain design features of new motor ambulances to meet medical requirements so that patients of any nation can be carried in any military motor ambulance.

STANAG-2873 ED.4 - Concept Of Operations Of Medical Support In Chemical, Biological, Radiological, And Nuclear Environments - Amedp-7(D)

STANAG-2874 ED.2 - Planning Guide For The Estimation Of Battle Casualties (Nuclear) - Amedp-8

The aim of this agreement is to register national acceptance of AMedP-8 to be used by the Armed Forces of the ratifying nations.

STANAG-2875 - Call For Destruction, Smoke, Illumination And Danger Close Missions

The aim of this agreement is to standardize, for the use of the NATO forces, a procedure to be used when Artillery observers call for Destruction, Smoke, Illumination and Danger Close Missions.

STANAG-2879 ED.3 - Principles Of Medical Policy In The Management Of A Mass Casualty Situation

STANAG-2882 ED.1 - Camouflage Requirements For Tents And Canvas Shelters

The aim of this agreeement is to state the requirements to be observed by NATO Forces in providing camouflage for tents and canvas shelters in the UV, visual and near IR wavebands.

STANAG-2884 ED.3 - Underwater Munition Disposal Procedures - Aeodp-1(A)

The aim of this agreement is to register national acceptance of AEODP-1(A) giving details of the identification and disposal of all underwater explosive ordnance (other than minor signals and pyrotechnics), for use by NATO forces.

STANAG-2885 ED.5 - Emergency Supply Of Water In Operations

STANAG-2887 - Tactical Tasks And Responsibilities For Control Of Artillery

STANAG-2888 ED.1 - Operational Carriage Of Ammunition & Fuel By Helicopter (Includes Amendments 1 Thru 4)

The air of this agreement is to standardize the regulations applicable when ammunition and fuel are to be carried as cargo by helicopters under operational conditions in peacetime or wartime.

STANAG-2889 ED.3 - Marking Of Hazardous Areas & Routes Through Them (Includes Amendments 2 & 3)

The aim of the agreement is to standardize those procedures which are used by NATO Forces to mark hazardous areas on land and those routes through or between such hazards.

STANAG-2890 ED.2 - Regulations For Safety In The Transport Of Ammunition & Explosives By Military Train (Includes Amendment 2)

The aim of this agreement is to standardize the procedures and regulations for safety in the transport of ammunition and explosives by military train in peace and war.

STANAG-2895 ED.1 - Extreme Climatic Conditions And Derived Conditions For Use In Defining Design/Test Criteria For Nato Forces Materiel

STANAG-2897 ED.4 - Eod Equipment Requirements And Equipment - Aeodp-7

STANAG-2899 ED.3 - Protection Of Hearing

The aim of this agreement is to establish principles for the protection of the hearing of personnel from damage as a result of exposure to high sound pressure levels encountered during military activities.

STANAG-2900 ED.2 - Laser Radiation - Medical Surveillance And Evaluation Of Over-Exposure

STANAG-2902 ED.2 - Criteria For A Nato Combat Helmet

STANAG-2905 ED.1 - Basic Voltage And Current Characteristics Of Electro-Medical Equipment

STANAG-2906 ED.3 - Essential Physical Requirements And Performance Characteristics Of Field Type High Pressure Steam Sterilizers

The aim of this agreement is to establish the essential physical requirements and performance characteristics for field type high pressure steam sterilizers to be used by NATO forces.

STANAG-2907 ED.2 - Procedures For Reporting And For Initial Disposition Of Unsatisfactory Medical Materiel And Drugs

The aim of this agreement is to standardize for the use of the NATO forces the procedures for reporting and recalling unsatisfactory medical material and drugs, when a cross-servicing of medical supplies exists.

STANAG-2908 ED.2 - Preventive Measures For An Occupational Health Programme

STANAG-2911 ED.2 - Design Criteria For Fragmentation Protective Body Armour

STANAG-2914 ED.1 - Mechanical Environmental Conditions To Which Materiel Intended For Use By Nato Forces Could Be Exposed - Aecp-1

The aim of this agreement is to promote the use, updating and application of AECP-1.

STANAG-2916 ED.2 - Nose Fuze Contours And Matching Projectile Cavities For Artillery And Mortar Projectiles

STANAG-2917 ED.2 - Chemical Casualty Assessment Exercise Publication - Axp- 7(A)

STANAG-2926 ED.2 - Procedures For The Use And Handling Of Freight Containers For Military Supplies

STANAG-2928 ED.7 - Catalogue Of Ammunitions Held By Nations That Satisfy Interchangeability Criteria Of Form, Fit And Fuction Only - Aop-6 Vol I

STANAG-2931 ED.2 - Orders For The Camouflage Of The Red Cross And Red Crescent On Land In Tactical Operations

STANAG-2933 ED.3 - Land Forces Explosives And Demolition Accessories Interchangeability Catalogue In Wartime - Aop-19

The aim of this agreement is to register national acceptance of AOP-19(B).

STANAG-2934 ED.3 - Artillery Procedures - Aartyp-1(B)

STANAG-2935 ED.2 - Interchangeable Ammunition For 105Mm Tank Gun: M68, L7A1, L7A2, L7A3 And F1 For Use On Peacetime Training Exercises

The aim of this agreement is to provide for interchangeability of ammunition for the 105 mm Tank Gun: M68, L7A2, L7A3 and F1. Ammunition listed in this agreement may be exchanged between nations and fired on peacetime training exercises.

STANAG-2937 ED.3 - Survival, Emergency And Individual Combat Rations - Nutritional Values And Packaging

STANAG-2939 ED.4 - Medical Requirements For Blood, Blood Donors And Associated Equipment (Including Amendment 2)

The aim of this agreement is to protect blood donors as well as recipients, where blood and blood products are exchanged between NATO Forces, by introducing uniform medical requirements for blood donors and regulations for transport and storage of blood.

STANAG-2940 ED.3 - Reporting Of Ammunition Malfunctions

STANAG-2941 ED.2 - Guidelines For Air And Ground Personnel Using Fixed And Transportable Collective Protection Facilities On Land

The aim of this agreement is to set out guidelines for nations to develop standardized procedures for personnel using fixed and transportable collective protection (colpro) facilities on land.

STANAG-2943 ED.1 - Regulations For The Lateral Or End-On Loading And Unloading Of Wheeled Or Tracked Military Equipment Transported On Railway Wagons

The aim of this agreement is to standardize, for the NATO forces, the regulation governing lateral or end-on loading or unloading of wheeled or tracked military equipment transported on railway wagons.

STANAG-2945 ED.2 - Nato Civil/Military Ground Fuels Interchangeability Catalogue - Aflp-1(A)

The air of this agreement is to register national acceptance of AFLIP-1 (A).

STANAG-2946 ED.1 - Forward Area Refuelling Equipment

The aim of this agreement is to provide standardized performance requirements and hardware interface to alloy forward area refuelling of member nations rotary wing aircraft engaged in land operations.

STANAG-2947 ED.4 - Technical Criteria For A Closed-Circuit Refuelling System

STANAG-2949 ED.3 - Technical Criteria For External Cargo Carrying Slings

The aim of this agreement is to provide standardized technical criteria for the design of a family of external cargo carrying slings with capacities to 20,000 kg (44,000 lbs).

STANAG-2950 ED.3 - Technical Criteria For External Cargo Carrying Nets

STANAG-2952 ED.1 - Procedures For Providing Restricted Areas For Nato Military Aircraft While Using Military Airfields Of Other Nato Nations

The aim of this agreement is to standardize the procedures for providing Restricted Areas for NATO and NATO members' military aircraft when using military airfields of other NATO nations.

STANAG-2953 ED.3 - The Identification Of Ammunition - Aop- 2(C)

STANAG-2956 ED.1 - Helicopter Tasking Messages

STANAG-2957 ED.5 - International System (Si) Units Used By Armed Forces In The Nuclear Field

STANAG-2960 - Standardization Of The Military Freight Warrant/Annulation

STANAG-2961 ED.3 - Classes Of Supply Of Nato Land Forces - App-19 Edition A

STANAG-2962 ED.1 - Call For Fire Procedure

STANAG-2963 ED.1 - Coordination Of Field Artillery Scatterable Mines

STANAG-2968 ED.1 - Land Forces Catalogue Of Bilateral Agreements On The Interchangeability And Safe Firing Of Ammunition During Peacetime Training Exercises - Aop-14

STANAG-2970 ED.3 - Aerial Recovery Equipment And Techniques For Helicopters

STANAG-2978 ED.1 - Essential Performance Characteristics Of Field Surgical Lights

STANAG-2979 ED.1 - Essential Characteristics Of Electro-Surgical Apparatus

STANAG-2980 ED.1 - Technical Criteria For External Cargo Carrying Nets

STANAG-2981 ED.1 - Prevention Of Cold Injury

STANAG-2984 ED.6 - Graduated Levels Of Chemical, Biological, Radiological And Nuclear Threats And Associated Protective Measures

STANAG-2989 ED.2 - Transfer Of Barriers

STANAG-2990 ED.1 - Principles And Procedures For The Employment In Land Warfare Of Scatterable Mines With A Limited Laid Life - Atp-50

STANAG-2991 ED.4 - Nato Combat Engineer Glossary - Aap-19(D)

STANAG-2999 ED.9 - Use Of Helicopters In Land Operations - Doctrine - Atp-49(F)

STANAG-3052 ED.5 - Aeronautical Briefing Facilities

The aim of this agreement is to establish the principles and basic criteria for the installation of aeronautical briefing facilities.

STANAG-3053 ED.6 - Characteristics Of Breathing Oxygen, Supply Pressure And Hoses

The aim of this agreement is to set out the minimum acceptable characteristics of gaseous breathing oxygen provided for the cross-servicing of aircraft; to list the supply pressures necessary for replenishment of aircraft systems; and to provide the essential characteristics of the supply hose.

STANAG-3054 ED.5 - Characteristics Of Compressed Air For Technical Purposes, Supply Pressure And Hoses

The aim of this agreement is to define the minimum acceptable characteristics of compressed air provided for the cross-servicing of aircraft, to specify an agreed supply pressure, and to define the essential characteristics of the supply hoses.

STANAG-3056 ED.6 - Marking Of Airborne And Ground Gas And Cryogenic Fluid Containers

The aim of this agreement is to provide an agreed method of marking airborne and ground gas and cryogenic fluid containers utilized in cross-servicing operations.

STANAG-3093 ED.5 - Nato Air Transport Request & Answer To Air Transport Request (Narat & Transar)

The aim of this agreement is to standardize the format of messages for requesting air transport support for use within NATO Forces.

STANAG-3094 ED.1 - 16 Bit Computer Instruction Set Architecture

The aim of this agreement is to standardize a 16 bit instruction set architecture to achieve easier development, lower cost hardware and software maintenance cost, re-use of software and a decrease of the life cycle costs of avionics computers and software.

STANAG-3097 ED.1 - Short Take-Off & Landing (Stdl) Airfield Marking

The aim of this agreement is to establish the marking of Short Take-Off and Landing (STOL) airfields and runways.

STANAG-3098 ED.11 - Aircraft Jacking - Aassep-1 Edition A

STANAG-3101 ED.15 - Exchange Of Safety Information Concerning Aircraft And Missiles

STANAG-3102 ED.5 - Flight Safety Co-Operation In Common Ground/Air Space

The aim of this agreement is to establish the requirement for co-ordination of accident prevention matters.

STANAG-3104 ED.6 - Identificatiion Of Aircraft And Missile Pipelines And Electrical Conduits

STANAG-3105 ED.7 - Pressure Refuelling Connections And Defuelling For Aircraft - Aassep-2 Edition A

STANAG-3109 ED.5 - Symbol Marking Of Aircraft Servicing And Safety/Hazard Points

STANAG-3111 ED.2 - Airfield Marking Tone Down

STANAG-3114 ED.8 - Aeromedical Training Of Flight Personnel

STANAG-3117 ED.7 - Aircraft Marshalling Signals

The aim of this agreement is to standardize aircraft marshalling signals and the distinctive garment to be worn by aircraft marshallers.

STANAG-3146 ED.1 - Planning Procedures For Tactical Air Transport Operations

The aim of this agreement is to standardize the planning procedures for tactical air transport operations to permit units to operate successfully together and to enable any units of any NATO nation to be air dropped or air landed by the aircraft of any other NATO nation.

STANAG-3149 ED.10 - Minimum Quality Surveillance Of Fuels

STANAG-3150 ED.8 - Codification - Uniform System Of Supply Classification

The aim of this agreement is to provide a uniform system of supply classification for use by the Armed Forces of the NATO countries.

STANAG-3151 ED.9 - Codification - Uniform System Of Item Identification

STANAG-3153 ED.8 - Aircraft Navigation And Anti-Collision Lights

The aim of this agreement is to establish common requirements for aircraft navigation and anti-collision lights.

STANAG-3154 ED.2 - Aircraft Formation Lights (Edition No. 2)

The aim of this agreement is to standardize the styles and types of formation lights to permit the execution of the various formation operations safely without violating visual security.

STANAG-3156 ED.3 - Aircraft Paratroop Signal Lights

To standardize the location, colour and meaning of paratroop signal lights in order to enable the parachuting personnel of any NATO nation to operate from the transport aircraft of any other NATO nations.

STANAG-3158 ED.7 - Day Marking Of Airfield Runways And Taxiways

STANAG-3159 ED.3 - Method Of Numbering Components Of Aircraft Engines

To standardize a method of numbering engine cylinders, combustion chambers, flame tubes, and similar components of all aircraft engines, in order to distinguish one from the other.

STANAG-3179 ED.6 - 16 Mm And 35 Mm Roll Film For Aerial Cameras

The aim of this agreement is to standardize the dimensions, tolerances, winding characteristics and labeling for 16 mm and 35 mm roll film for aerial cameras.

STANAG-3180 ED.3 - Sheet Photographic Paper For Air Photography (With Amendment 1 Incorporated)

STANAG-3181 ED.3 - Rolled Photographic Paper For Air Photography (With Amendment 1 Incorporated)

STANAG-3182 ED.3 - Nato High Contrast Developer (Edition N0. 3)

STANAG-3187 ED.3 - Labelling Of Pre-Packaged Photographic Chemicals

STANAG-3188 ED.3 - Negative Film Black And White For Air Photography

To standardize the classification of air films in accordance with defined methods of measuring their principal sensitometric and physical characteristics related to certain conditions of use.

STANAG-3198 ED.4 - Functional Requirements Of Aircraft Oxygen Equipment And Pressure Suits

STANAG-3200 ED.8 - Minimum Requirements For G Protective Sytems

STANAG-3205 ED.3 - Points Designation Template For Air Imagery

STANAG-3207 ED.3 - Aircraft Grounding Plug

STANAG-3208 ED.6 - Air Conditioning Connections

STANAG-3209 ED.5 - Tyre Valve Couplings

STANAG-3210 ED.3 - Grease Nipples

To standardize aircraft grease nipples.

STANAG-3212 ED.6 - Diameters For Gravity Filling Orifices

STANAG-3213 ED.2 - Angles Of Heads For Countersunk Rivets (With Amendments 1 And 2 Incorporated)

STANAG-3216 ED.5 - Layout Of Flight Data In Pilots Displays

The aim of this agreement is to standardize the layout of flight data in pilots' displays.

STANAG-3217 ED.6 - Operation Of Controls And Switches At Aircrew Stations

STANAG-3218 ED.6 - Location, Actuation And Shape Of Engine Controls And Switches

The aim of this agreement is to standardize the location, actuation and shape of all engine controls and switches in fixed and rotary-wing aircraft.

STANAG-3219 ED.4 - Location And Grouping Of Electrical Switches In Aircraft

To standardize the location and grouping of various electrical switches in aircraft so that a pilot can always expect to find switches for a particular service in the same cockpit area.

STANAG-3220 ED.4 - Location, Actuation And Shape Of Airframe Control For Fixed Wing Air- Craft

The aim of this agreement is to standardize the location, actuation and shape of airframe controls for fixed wing aircraft.

STANAG-3221 ED.6 - Automatic Flight Control System (Afcs) In Aircraft - Design Standards And Location Of Controls

The aim of this agreement is to standardize the AFCS panel and controller location, the nomenclature and other functional areas of AFCS.

STANAG-3223 ED.4 - Flight Documents Stowages In Crew Compartments

STANAG-3225 ED.4 - Location, Actuation & Shape Of Airframe Controls For Rotary Wing Aircraft

The aim of this agreement is to standardize the location, actuation and shape of airframe controls for rotary wing aircraft.

STANAG-3226 ED.2 - Policy On Supply Forms

STANAG-3230 ED.7 - Emergency Markings On Aircraft

STANAG-3231 ED.2 - Aden And Defa 30 Mm Gun Barrel Chambers For Aircraft

To standardize NATO 30 mm gun barrel chambers.

STANAG-3232 ED.2 - 30Mm Link For Aden And Defa Guns

STANAG-3236 ED.9 - Designation System For Aircraft And Designation Of Role Codes Of Aircraft

The aim of this agreement is to establish for NATO forces the method of designating aircraft and the role codes of aircraft.

STANAG-3237 ED.3 - Aperture Of Terminal Ring Or Link Of Aircraft Lifting Slings

STANAG-3240 - Pyrotechnic And Flashing Lamp Signals For Air Traffic Control

STANAG-3242 ED.4 - Gca Procedures And Associated R/T Phaseology

The aim of this agreement is to set forth common basic GCA procedures.

STANAG-3243 - Controlled D/F Descents (With Amendments 1, 2)

STANAG-3244 - Non-Directional Beacon (Ndb) Vhf Omni- Directional Range (Vor), Tacan And Radio Range Approaches

To standardize the procedure for NDB, VOR, TACAN and Radio Range approaches.

STANAG-3254 ED.3 - Loan Of Materiel For Test Purposes In Support Of Standardization, Research And Development

STANAG-3256 ED.2 - Power Supplies For Testing Airborne Electrical Equipment

STANAG-3258 ED.6 - Position Of Pilot Operated Navigation And Radio Controls

STANAG-3261 - Portrayal Of Global Navigation Grid And Associated Isogriv Information

STANAG-3275 ED.3 - Method Of Warning Own Aircraft Of (Suspected) Enemy Fighter Attacks

The aim of this agreement is to standardize the methods of warning own aircraft of (suspected) enemy fighter attacks.

STANAG-3276 ED.3 - National Air Statistical Co-Ordinators

STANAG-3277 ED.7 - Air Reconnaissance Request/Task Form

The aim of this agreement is to adopt a standard air reconnaissance request/task form for use by the NATO Forces.

STANAG-3278 ED.8 - Aircraft Towing Attachments And Devices

STANAG-3279 ED.3 - Emergency Towing Equipment

The aim of this agreement is to standardize the emergency towing fitting provided on aircraft.

STANAG-3281 ED.5 - Personal Locator Beacons

The aim of this agreement is to standardize the characteristics of Personal Locator Beacons to ensure compatibility amongst nations.

STANAG-3294 ED.4 - Aircraft Fuel Caps And Fuel Cap Access Covers

STANAG-3295 ED.7 - Horse Collar/Rescue Strop Type Helicopter Hoisting Gear

STANAG-3296 ED.3 - Aircraft Gaseous Oxygen Replenishment Couplings

STANAG-3297 ED.6 - Nato Standard Aerodrome And Heliport Ats Procedures

STANAG-3298 - Tacan Instrument Approach Criteria (With Amendments 1 And 2 Incorporated)

To standardize Obstruction Clearane Criteria which will be used by the Nato Armed Forces in the development of high and low altitude TACAN instrument approach procedures.

STANAG-3300 ED.6 - Nato Glossary Of Aircraft Armament Terms And Definitions (English And French) - Aap-46

STANAG-3302 ED.5 - Connectors For 28 Volts

The aim of this agreement is to establish standard external DC servicing power connections to aircraft.

STANAG-3303 ED.3 - Connectors For 115/200 Volts, 400 Hertz, 3 Phase, Ac Servicing Power (S/S By Stanag-7073)

The aim of this agreement is to standardize the external AC servicing power supply connectors (plugs and receptacles)

STANAG-3312 ED.4 - Profile Dimensions Of Flanges For V-Band Couplings For Piping And Ducting

STANAG-3313 ED.3 - Jacking Of Aircraft

The aim of this agreement is to standardize primary jacking requirements, including tyre and wheel changing.

STANAG-3314 ED.3 - Interchangeability Of Terminals (Lugs)

STANAG-3315 ED.8 - Aircraft Cabin Pressurizing Test Connections

The aim of this agreement is to standardize cabin pressurizing test connection, canopy seal inflation connection, and/or test pressure gauge connection as well as access clearance requirements so as to facilitate cross-servicing of the aircraft of member nations.

STANAG-3316 ED.10 - Airfield Lighting

STANAG-3317 ED.5 - Aircraft Electrical Cables

To standardize a range of stranded flexible cables for general purpose use in aircraft to ensure interchangeability.

STANAG-3318 ED.7 - Aeromedical Aspects Of Aircraft Accident And Incident Investigation - Aamedp-1.7 Edition A

STANAG-3319 ED.6 - Dimensions For Cases Of Control Boxes, Instruments And Panel Mounted Equipment

STANAG-3320 ED.7 - Circular Dial Type Vertical Speed Indicators (Barometric)

The aim of this agreement is to standardize circular dial type vertical speed indicators fitted to aircraft.

STANAG-3322 ED.7 - Turn & Slip Indicators

The aim of this agreement is to standardize the main features of the presentation, performance and case size for turn and slip indicators.

STANAG-3323 ED.5 - Pipe (Tube) Connections To Aircraft Instruments (Imperial And Metric)

The aim of this STANAG is to establish standard dimensions for pipe (tube) connectors and adapters to aircraft instruments.

STANAG-3325 ED.3 - Detailed Procedures And Techniques For Forward Air Controlling (Supplement No. 1 To Atp-27(A)

STANAG-3326 ED.3 - Manifold Pressure Gauges

STANAG-3327 ED.2 - Air Transportation Of Dangerous Cargo

To standardize a procedure to permit explosives, radioactive materials and other dangerous cargo of one NATO nation to be carried in another NATO nations aircraft during emergency or war.

STANAG-3328 ED.2 - Nato Standard Conversion Tables For Metric, American And British Units Of Measurement, Aap-9 (With Amendments 1 Thru 4 Incorporated)

To standardize the conversion of Metric, American and British units of measurement by means of conversion tables.

STANAG-3329 ED.6 - Numerals And Letters In Aircrew Stations

STANAG-3330 ED.4 - Indicating Accelerometers

The aim of this agreement is to standardize the presentations, controls and case sizes of Indicating Accelerometers.

STANAG-3332 ED.3 - System For Tracing Missing Air Cargo

To standardize the procedure to be used by the NATO Armed Forces when discrepancies are noted on the delivery of air transported freight or equipment.

STANAG-3334 ED.4 - Defuelling Of Aircraft

The aim of this agreement is to ensure the provision of a selective aircraft defuelling capability and to establish standard practices which will facilitate the completion of defuelling operations.

STANAG-3337 - Indexes To Series Of Aeronautical Charts

STANAG-3338 ED.4 - Machmeters

The aim of this agreement is to establish standard case size, display and control features, minimum performance requirements and aircraft system interfacing for Machmeters.

STANAG-3339 ED.5 - Fuel Contents Gauges

The aim of the agreement is to establish the units of measurement and the features of presentation for fuel contents gauges.

STANAG-3341 ED.3 - Emergency Control Colour Schemes

The aim of this agreement is to adopt a standard colour scheme for emergency controls in aircraft.

STANAG-3344 ED.3 - Procedures For Tracing And Disposing Of Air Baggage (Baglo-Trobag)

To standardize procedures for tracing missing air baggage and disposing of found air baggage.

STANAG-3345 ED.6 - Data/Forms For Planning Air Movements

STANAG-3347 ED.5 - Identification Of Aircraft Electrical Circuits

STANAG-3350 ED.4 - Analogue Video Standard For Aircraft System Applications

STANAG-3359 ED.5 - Location And Arrangement Of Engine Displays In Aircraft

STANAG-3365 ED.2 - Suspension Units With Gravity Release Capability For Aircraft Stores

STANAG-3368 ED.3 - Internal Aircraft Engine Starting Systems

STANAG-3370 ED.6 - Aircrew Station Alerting Systems

The object of this STANAG is to establish uniform requirements and provide functional design criteria for an effective aircrew station alerting system. The use of new technology is encouraged where it can be demonstrated that the use of the technology will result in shorter aircrew response times and more effective aircrew action subsequent to presentation of the alert.

STANAG-3372 ED.6 - Low Pressure Air And Associated Electrical Connections For Aircraft Engine Starting

STANAG-3374 ED.6 - Flight Inspection Of Nato Radio/Radar Navigation And Approach Aids - Aetp-1(D)

STANAG-3381 ED.1 - Nato Standard Procedures For Compensation And Form For Request And Receipt Of Support In The Form Of Supplies And Services

STANAG-3388 ED.1 - Airborne Radio Controlunits

STANAG-3390 ED.11 - Guide Specification And Inspection Standards For Fuel Soluble Lubricity Improvers (S-1747)

STANAG-3394 ED.3 - Angles Of Heads For Countersunk Screws

STANAG-3398 ED.3 - Air Pyrotechnics Interchangeability Chart

STANAG-3402 - Recovery And Release Of Parachutists Towed Behind Aircraft

STANAG-3405 ED.3 - Dimensions Of Clock Cases (With Amendment 1 Incorporated)

STANAG-3408 ED.3 - Position Reference Systems For Aeronautical Charts

STANAG-3409 ED.5 - Projections For Aeronautical Charts

STANAG-3411 - Base Symbols And Aeronautical Data For Aeronautical Charts

STANAG-3412 ED.6 - Aeronautical Information On Aeronautical Charts

The aim of this agreement is to define the essential aeronautical information to be portrayed on aeronautical charts for use within the NATO area of operational interest.

STANAG-3416 ED.5 - Methanol/Water And Demineralized Water Replenishment

STANAG-3418 ED.2 - Film Cores

The aim of this agreement is to standardize dimensions and design criteria for 16mm and 70mm film cores to permit interchangeability of film procured on cores.

STANAG-3419 ED.3 - Film Spools For Aerial Cameras

The aim of this agreement is to establish the specifications for film spools used in aerial cameras.

STANAG-3420 ED.3 - Photoflash Cartridges For Low Altitude Photography For Fixed Wing Aircraft

STANAG-3427 ED.4 - Colours For The Identification Of Airdropped Supplies

STANAG-3428 ED.6 - Exchange Of Information On Aerial Delivery Systems

STANAG-3436 ED.4 - Colours And Markings Used To Denote Operating Ranges Of Aircraft Instruments

STANAG-3440 ED.1 - Compatibility Of Air To Ground Rocket Launcher Systems For Fixed Wing Aircraft And Helacopters

STANAG-3441 ED.8 - Design Of Aircraft Stores

STANAG-3443 - Oil Compressed Nitrogen Characteristics Supply Pressure And Hoses

STANAG-3444 ED.2 - Dimensions Of Elastomeric O-Rings For Aircraft (Inch Series)

The aim of this agreement is to standardize on the dimensions and methods of designation of elastomeric O-rings (inch series) that are used in aircraft fuel, hydraulic, lubricating oil, or other systems containing liquids or gases.

STANAG-3445 ED.1 - Dimensions Of Tapped Holes For Wire Thread Inserts (Inch Series)

STANAG-3446 ED.2 - Screwdriver Recesses (Low Torque Drive) Cross

The aim of this agreement is to standardize on the low torque driving recesses to be used for driving general purpose aircarft fasteners of up to 14mm shank diameter.

STANAG-3447 ED.3 - Aerial Refueling Equipment Dimensional And Functional Characteristics

The aim of this agreement is to standardize the mating dimensions of the reception coupling and of the nozzle/probe mast to be fitted to aircraft required to engage in refueling operations during flight and also the nozzle/probe mast clearance envelope and the maximum aerial refuelling pressure to facilitate aerial refuelling between aircraft of NATO forces.

STANAG-3448 ED.2 - Standard Synchro Electrical Characteristics For Aircraft Instruments

To standardize the electrial input characteristics of aircraft instruments driven from a remote synchro source to ensure to interchangeability of the instruments.

STANAG-3449 ED.2 - Vertical Scale Tape Indicating Flight 1Nstruments

STANAG-3451 ED.2 - Combined Speed Indicator

STANAG-3454 ED.6 - Ground Recharging Of Aircraft Main Batteries - Aaep-01 Edition A

STANAG-3455 ED.5 - Basic Symbols For Aircraft Electrical Circuits

STANAG-3456 ED.7 - Aircraft Electrical Power System Characteristics

STANAG-3459 ED.1 - Precision, High-Melting-Point, Cartridge Fuze Links Used On Aircraft

To facilitate cross-servicing of aircraft by standardizing the essential characteristics of precision, high-melting-point cartridge fuses as follows.

STANAG-3462 ED.4 - Availability Of Weight And Balance Requirements And Loading Criteria For Transport Aircraft

The aim of this agreement is to standardize weight and balance requirements to permit the loading of transport aircraft of one nation to be carried out correctly by the personnel of another nation under supervision of the aircraft crew.

STANAG-3463 ED.1 - Planning Procedures For Tactical Air Transport Operations For Fixed Wing Aircraft

STANAG-3464 ED.3 - Procedures For Aircrew And Airlifted Personnel In Tactical Air Transport Operations

The aim of this agreement it to determine and standardize procedures to be followed in various NATO tactical and transport operations.

STANAG-3465 ED.5 - Safety, Emergency And Signalling Procedures For Military Air Movement - Fixed Wing Aircraft

The aim of this agreement is to establish safety, emergency and signalling procedures to be used when engaged in transporting personnel on joint air transport or airborne operations.

STANAG-3466 ED.3 - Responsibilities Of Air Transport Units And User Units In The Loading And Unloading Of Transport Aircraft In Tactical Air Transport Operations

STANAG-3467 ED.3 - Characteristics Of Air Transport (Air Landed) Pallets For Carriage Internally

STANAG-3468 ED.3 - General Rules Concerning The Transport Of Loads By Helicopter

The aim of this agreement is to establish general rules governing the transport of loads by helicopter to permit interoperability of helicopters.

STANAG-3469 ED.3 - Parachute Extraction Assemblies And Aircraft Extraction Parachute Ejector Installations

STANAG-3472 - Medical Protective Measures Associated With Missile Operations (With Amendment 1 Incorporated)

STANAG-3473 - Hearing Conservation (With Amendment 1 And 2 Incorporated)

To establish a hearing conversation programe used to protect the auditory mechanisms of personnel from damage as a result of exposure to high sound pressure levels encountered during military activities.

STANAG-3474 ED.5 - Temporary Flying Restrictions Due To Exogenous Factors Affecting Aircrew Efficiency

STANAG-3487 - Metric Thread-Nuts, Bolts, Screws And Similar Parts (With Amendments 1 And 2 Incorporated)

STANAG-3491 ED.6 - Calibration & Accuracy Of Aircraft Barometric Altimeters (Imperal & Metric)

The aim of this agreement is to standrdize calibration procedures for aircraft barometric altimeters.

STANAG-3492 ED.5 - Clamps, Mounting (Imperial And Metric) For Aircraft Instruments

The aim of this agreement is to standardize the mounting clamps for flangeless instruments in order to facilitate interchanging of these instruments and to ensure their secure attachment.

STANAG-3495 ED.2 - Standard Pressure/Altitude Relationship Tables For Aircraft Equipment

To provide standard pressure/altitude values to be used in the design and calibration of those aircraft equipments whose operation is a function of atmospheric pressure.

STANAG-3497 ED.3 - Aeromedical Training Of Aircrew In Aircrew Cbrn Equipment And Procedures

STANAG-3499 ED.2 - Characteristics Of Supply Equipment For Liquid Oxygen

The aim of this agreement is to ensure minimum acceptable characteristics of charging connectors used in replenishment of aircraft liquid oxygen systems, thereby increasing the effectiveness of aircraft cross-servicing.

STANAG-3501 ED.3 - Performance Of Portable Filter-Blowers For Aircrew Cbrn Respirators

STANAG-3504 ED.2 - Cathode Ray Tube Head Down Displays (Monochrome)

missible temperature of any cockpit material for non-injurious contact with the bare skin; and (b) selection of appropriate materials and/or coating to provide thermally safe cockpit interiors to prevent injury and possible loss of operational control due to unexpected instantaneous pain or burn on contact.

AIR-STD-61/4 - Flotation And Sea Survival, Test Methods And Requirements

To standardize the requirements for inflatable life preservers.

AIR-STD-61/40 - A Technical Basis For Specifying The Insulation Of Immersion Protective Clothing

To standardize the technical basis upon which national guidelines to commanders may be drawn up in respect of the insulation requirements of immersion protective clothing.

AIR-STD-61/41 - Procedures For Calibration Of In-Flight Respiratory Data Acquisition Equipment

To define the procedures to be adopted for the calibration of equipment used in the acquisition of in-flight respiratory data.

AIR-STD-61/45 - Aviation Medicine/Physiological Training Of High Altitude Parachutists

To define the minimum aviation medicine/physiological training for high altitude parachutists.

AIR-STD-61/48 - Single Number Noise Reduction Of Hearing Protectors

The object of this AIR STD is to establish a method for calculating a single number moise reduction value to describe the overall performance of hearing protectors.

AIR-STD-61/5 - Escape Path Clearance In Ejection Seat Aircraft

AIR-STD-61/6 - Collection Of Data For Evaluation Of Helmets Damaged In Service (S/S By Air-Std-61/102)

To standardize the data collected from helmets damaged in service.

AIR-STD-61/7 - Minimal Protection For Aircrew Exposed To Altitudes Above 50,000 Feet

AIR-STD-61/73 - Minimum Standards For Breathing Equipment For Parachutists Between 13,000 & 25,000 Feet Pressure Altitude

AIR-STD-61/79 - Terminology Of Aeromedical Evacuation

AIR-STD-61/8 - Criteria For Reporting The Nature Of Clothing Materials On Assemblies Subjected To Physical & Operational Testing

AIR-STD-61/80 - Documentation Of Aeromedical Evacuation

AIR-STD-61/81 - Tests For Protective Capacity Of Fire Resistant Clothing Materials

AIR-STD-61/82 - Instrumentation For Escape System Thermal Hazard Analysis

AIR-STD-61/83 - A Basis For Common Practices And Goals In The Conduct Of Anthropometric Surveys

AIR-STD-61/84 - Initial Investigation And Immediate Management Of Laser Eye Injury In Aircrew

AIR-STD-61/9 - Protection Of Personnel Against The Effects Of High Levels Of Sound Upon Hearing & Operational Efficiency

AIR-STD-64/11 - Delineation Of Air Defense Identification Zones On Aeronautical Charts And Flight Information Publications

To ensure that Air Defense Identification Zones (ADIZ), when shown, are delineat4ed in the same manner on all aeronautical charts and Flight Information Publications.

AIR-STD-64/12 - Delineation Of The International Date Line On Aeronautical Charts And Flight Information Publications

To ensure that the placement of the International Date Line is the same on all aeronautical charts and Flight Information Publications.

AIR-STD-64/15 - Flight Information Publication, Enroute

To promote the standardization of Enroute Flight Information Publications produced by member nations to facilitate their use by any of the participating air forces.

AIR-STD-64/16 - Flight Information Publications - Planning

AIR-STD-64/18 - Title For Flight Information Publications

To standardize titles for Flight Information Publications (FLIP).

AIR-STD-64/19 - Explanatory Information Required On Aeronautical Charts

To identify the explanatory information to be shown on seronautical charts to satisfy the combined operational requirements of the member air force.

AIR-STD-64/20 - Operational Usage Criteria (S/S By Adv Pub 64/39)

AIR-STD-64/21 - Abbreviations And Code Legend Flight Information Publications 141166

AIR-STD-64/23 - Identification Of Scale On Aeronautical Charts

To enable participating air forces, by adoption of a common method, to identify without special instructions the scale of any aeronautical chart produced by any one of the air forces.

AIR-STD-64/24 - Symbols For Aeronautical Charts

To standardize the symbols used on aeronautical charts in order that air forces of one country may more easily use the aeronautical charts produced by participating nations.

AIR-STD-64/25 - Minium Content And Colour Of Aeronautical Information For Aeronautical Charts

AIR-STD-64/26 - Position Reference Systems For Aeronautical Charts

To identify a combined operational requirement to adopt basic position reference systems for use on aeronautical charts produced by participating nations.

AIR-STD-64/27 - Standard Scales For Topographic Aeronauticalcharts

To identify an operational requirement to adopt standard scales for topographic aeronautical charts produced by participating nations.

AIR-STD-64/28 - Definitions Of Aeronautical Map And Chart And Flight Information Terms

To establish a directory of terms and their definitions so that participating air forces may use without special instructions.

AIR-STD-64/29 - Aeronautical Chart Catalogues

AIR-STD-64/30 - Flight Information Publication Terminal

AIR-STD-64/31 - Identification Of Aerodrome By Name

To aid aircrew in the identification of aerodromes by the adoption of a common system for selecting the name under which the primary entry will appear in listings and on charts.

AIR-STD-64/32 - Aeronautical Chart Projections

AIR-STD-64/33 - Portrayal Of Navigation Grid Information

AIR-STD-64/34 - Identification Of Airspace Reservations (With Amendment 1)

AIR-STD-64/35 - Maximum Elevation Figure Criteria For Aeronautical Charts

To standardize the computation of Mximum Elevation Figures to be shown within the designated quadrangles on the aeronautical charts.

AIR-STD-64/36 - Aircraft Arresting Sysems, Information For Flips

To standardize the presentation of information related to aircraft arresting systems in enroute supplement and on instrument approach charts (terminal).

AIR-STD-64/37 - Flip Operational Abbreviations

To maintain a decode list of the operational abbreviations used in member nations' Flight Information Publications (FLIPS) and aeronautical charts.

AIR-STD-64/38 - Asw Dead Reckoning Tracker Plotting Charts

AIR-STD-64/6 - Standard Units Of Linear Measurement On Aeronautical Charts And Flight Information Publications (Req Other Than Dod Ref Hq Usaf/X0Xx-Iso, Washg., Dc 20330-5058 ( No S/S Document)

To identify standard units of linear measurement to be used on aeronautical charts and Flight Information Publications to satisfy the combined operational requirements of the member air forces.

AIR-STD-64/94 - Guidelines For The Assessment Of Thermal Stress In Aircraft Chemical Defense Operations

AIR-STD-65 - Changes To Ascc Air Standards/Advisory Publications - Working Party 65 - Airfield Marking & Lighting & Other Visual Aids

AIR-STD-65/1 - Lighting Of Instrument And Non-Instrument Runways

AIR-STD-65/10 - Airfield Lighting Control Systems

To standardize the airfield lighting control systems.

AIR-STD-65/11 - Illuminated Runway Distance Markers And Illuminated Hook Cable Markers

To achieve standardization between ASCC nations on Illuminated Runway Distance Markers (IRDM) and Illuminated Hookcable Marker (IHCM) as visual aids to aircraft operations at military airfields.

AIR-STD-65/12 - Airfield Lighting For Category 11 Operations

AIR-STD-65/13 - Extraneous Lighting In Vicinity Of Aerodromes

AIR-STD-65/14 - Airfield Marking And Lighting Color Standards

To establish standard colours for aeronautical ground light and surface markings.

AIR-STD-65/15 - Airfield Lighting Circuitry

AIR-STD-65/16 - Helipad Lighting (Vmc)

To establish a system of helipad lighting for Visual Meteorological Conditions (VMC).

AIR-STD-65/17 - Aerodrome Illuminated Markers And Signs

AIR-STD-65/18 - Apron Floodlighting

AIR-STD-65/19 - Standby Power Supply Requirements For Fixed Installations

AIR-STD-65/2 - Lighting Of Airfield Obstructions (Rel To Other Than Dod Act Req Pri Appr Of Hq Usaf/Xoxx-Iso Wash, Dc 20330-5058)

AIR-STD-65/21 - Helipad Marking

To standardize the markings of helipads at heliports, other than those heliports which use a runway for the helicopter landing area.

AIR-STD-65/22 - Airfield Clearance Planes

AIR-STD-65/23 - Aircraft Arresting Gears For Airfields

AIR-STD-65/24 - Air Traffic Control Procedures For Arrestment Of Aircraft

To ensure that each Member Nation using aircraft arresting systems of other Member Nations can expect Air Traffic Control to comply with a standard procedure.

AIR-STD-65/25 - Signals For Runway Party When Disengaging An Aircraft After A Hook Cable Arrestment

AIR-STD-65/26 - Pilots Operating Procedure For Engagement Of Airfield Arresting Systems (Issued Controlled)

The purpose of this ASCC AIR STD is to standardize pilot's procedure for engagement of airfield arresting systems.

AIR-STD-65/3 - Lighting And Marking Of Airfield Obstructions

To standardize the marking of airfield obstructions.

AIR-STD-65/30 - Pacific Nations Helicopter Operations From Ships Other Than Aircraft Carriers (Pac Hostac) Publications (Pac Hostac (Pac 1) And Pac Hostac Supplement (Pac 1-1)

To register national acceptance of PAC HOSTING (PAC 1) and PAC HOSTING Supplement (PAC 1-1).

AIR-STD-65/31 - Airfield Tone-Down Marking (S/S By Air-Std-65/36)

To standardize airfield tone-down markings.

AIR-STD-65/32 - Non-Tactical Heliport Lighting And Marking (Issued Controlled)

To establish heliport marking and lighting systems for visual meteorological conditions (VMC) and instrument meteorological (IMC) at heliports.

AIR-STD-65/33 - Airfield Declared Distances

To standardize the terminology and criteria for airfield declared distances.

AIR-STD-65/34 - Heliport And Helipad Lighting And Marking

The purpose of this agreement is to standardize lighting and marking of Heliports and Helipads.

AIR-STD-65/37 - Aircraft Arresting Systems Operating Procedures

AIR-STD-65/4 - Airfield Approach Lighting

AIR-STD-65/5 - Marking Of Instrument And Non-Instrument Runways (S/S By Air-Std-65/36)

AIR-STD-65/6 - Airfield Taxiway Markings (S/S By Air-Std-65/36)

AIR-STD-65/7 - Visual Glide Slope Indicator Systems

AIR-STD-65/8 - Airfield Portable Lighting Systems

AIR-STD-65/9 - Taxiway Lighting

AIR-STD-70/10 - Standard Analogue Heading Outputs

To establish scale factors and synchro voltages for the transmission of healing information.

AIR-STD-70/11 - The Specification For Evaluation Of The Accuracy Of Inertial Navigation Systems

To adopt a standard method of determining the position accuracies of pure Inertial Navigation Systems.

AIR-STD-70/13 - The Specification For Evaluation Of The Accuracy Of Airborne Doppler Navigation Systems

To adopt a standard method of determining the position accuracies of airborne doppler navigation systems.

AIR-STD-70/14 - Definition Of Sea State For Use In Connection With Doppler Navigation

AIR-STD-70/16 - The Specification For Evaluation Of The Accuracy Of Hybrid Navigation Systems

AIR-STD-70/17 - Definitions Of Aircraft Attitude And Heading Angles

The purpose of this agreement is to define the terminology used when referring to aircraft attitudes and manouevres.

AIR-STD-70/18 - Microwave Landing Systems (Mls)

AIR-STD-70/3 - Interoperability Of Aircraft Vhf Am And/Or Fm Multi-Frequency Transceiver Installations And Compatible Ground Radio Equipments

AIR-STD-70/4 - Interoperability Of Aircraft Uhf Multi-Frequency Transceiver Installation And Compatible Ground Transmitters And Receivers

AIR-STD-70/7 - Data Transmission For Radar Doppler Systems

To establish data transmission criteria for use in doppler radar systems.

AIR-STD-70/8 - True Airspeed Outputs

AIR-STD-80/1 - Method Of Determining The Principal Sensitometric Characteristics Of Black And White Rolled Air Film

AIR-STD-80/10 - Air Reconnaissance Request/Task Form

The purpose of this agreement is to standardize the format for requesting and tasking air reconnaissance by ASCC Armed Forces.

AIR-STD-80/11 - Titling Of Hand-Held Imagery (Wet)

AIR-STD-80/13 - Air Reconnaissance Intelligence Reporting Nomenclature

To standardize nomenclature for describing equipment and installations in imagery reports.

AIR-STD-80/14 - Point Designation Template For Imagery

To specify basic parameters to be observed in the construction of a universal grid for use in identifying a precise point of area on a frame of imagery.

AIR-STD-80/15 - Minimum Resolved Object Sizes For Imagery Interpretation

The purpose of this agreement is to specify minimum resolved object sizes required in imagery used for interpretation and technical analysis.

AIR-STD-80/18 - Reporting Of Data Used For Dimensional Analysis Of Imagery

The purpose of this agreement is to standardize the reporting of data used for dimensional analysis of imagery.

AIR-STD-80/3 - Dimensions, Tolerances And Characteristics Of 70Mm, 126Mm And 240Mm Rolled Film For Air Photography

To adopt standard dimensions, tolerances and characteristics for 70mm, 126mm, and 240mm rolled film for air photography, to permit the common use of film in cameras and processing equipment.

AIR-STD-80/5 - Target Pattern For Determination Of Aerial Photographic Resolution

The purpose of this agreement is to adopt a standard target pattern for determining the photographic resolution of aerial cameras used by ASCC nations during airborne operations.

AIR-STD-80/7 - Lm-230A/B Programmable Automatic Camera Test Set

AIR-STD-80/8 - Air Reconnaissance Intelligence Report Forms

To standardize and consolidate Air Reconnaissance Report Forms for reporting and presenting intelligence information derived from air reconnaissance and sensor imagery.

AIR-STD-84/11 - Casualty Handling In A Cw Environment

AIR-STD-84/12 - Peacetime Nuclear Weapons Accidents - Division Of Responsibilities

AIR-STD-84/13 - Peacetime Nuclear Weapons Accidents - Key Control Areas

AIR-STD-84/2 - Commander S Guide On The Effects Of Penetrating Ionizing Radiation (With Change 1)

To provide a standard method, within the ASCC member services, of categorizing the Radiation Exposure State of individuals, and groups of individuals, and to provide common guidance for Commanders.

AIR-STD-84/4 - First Aid Materiel For Chemical Injuries (With Change 1)

The purpose of this agreement is to standardize the minimum essential items of medical first-aid materiel for chemical injuries.

AIR-STD-84/9 - Nbc Defense Evaluation Of Air Bases

To identify the criteria for evaluating the effectiveness of Air Forces operating in an NBC environment.

AIR-STD-85/1 - Glossary Of Terms And Definitions

AIR-STD-90/4 - Aircraft Arresting Systems Information For Flips

The purpose of this agreement is to standardize the presentation of information related to aircraft arresting systems in enroute supplement and on instrument approach charts (terminal).

AIR-STD-94/3 - Comparative List Of Ascc Terms And Definitions For Nuclear Accident Response

To provide a comparative list of terms and definitions used by Member nations related to Nuclear Accident Response.

AOP-15 ED.3 - Guidance On The Assessment Of The Safety And Suitability For Service Of Non-Nuclear Munitions For Nato Armed Forces

AOP-16 ED.4 - Fuzing Systems: Guidelines For Stanag 4187

AOP-22 ED.1 - Design Criteria And Test Methods For Inductive Setting Of Electronic Projectile Fuzes

AOP-7 ED.2 - Manual Of Data Requirements And Tests For The Qualification Of Explosives Materials For Military Use

The primary objectives of this document are to promote standardization and interoperability of munitions among the NATO countries.

AOP-8 ED.2 - Nato Fuze Characteristics Catalogue

AQAP-100 ED.3 - Policy On An Integrated Systems Approach To Quality Through The Life Cycle

This document should be used, as a part of the overall policy of an organisation, to ensure quality of life cycle processes, products and services.

AQAP-11 - Nato Guideline For Specification Of Technical Publication

AQAP-110 ED.2 - Nato Quality Assurance Requirements For Design, Development And Production

AQAP-119 ED.2 - Nato Guide To Aqaps-110, -120, -130

AQAP-120 ED.2 - Nato Quality Assurance Requirements For Production

AQAP-130 ED.2 - Nato Quality Assurance Requirements For Inspection And Test

AQAP-131 ED.1 - Nato Quality Assurance Requirements For Final Inspection

AQAP-150 ED.2 - Nato Quality Assurance Requirements For Software Development Aqap-150

This publication specifies the project oriented requirements to manage the quality of the software development process.

AQAP-159 ED.2 - Guidance For The Use Of Aqap-150

This publication specifies the project oriented requirements to manage the quality of the software development process.

AQAP-170 ED.2 - Nato Guide For The Delegation Of Government Quality Assurance

AQAP-8 - Nato Guide To The Preparation Of Specifications For The Procurement Of Defence Material

ARMP-1 ED.4 - Nato Requirements For Reliability And Maintainability

ARMP-2 ED.2 - General Application Guidance On The Use Of Armp-1

ARMP-3 ED.2 - List And Source Of National And International Reliability And Maintenability Documents

ARMP-3 catalogues R&M Standards and other documents, military and civilian, which are produced by NATO countries.

ARMP-4 ED.4 - Guidance For Writing Nato R&M Requirements Documents

ARMP-6 ED.3 - Guidance For Managing In Service R & M

QAP-15 - Glossary Of Terms Usedin Proof (Rel To Other Than Dod Agencies Must Be Approved By Darcom, Drcde)

This QAP has been approved for use by the Armies of the United States, United Kingdom, and Australia and the Canadian Forces, as a Glossary of Terms used in Proof.

QAP-17 - Metallurical Terms & Definitions, Listing Of Glossaries Used By Armies (Req Other Than Dod Ref To Darcom, Drcde-1)

QAP-22 - Military Operations In Urban Terrain - Bibliography

QAP-9 - Engine Health Monitoring For Army Aircraft, Manual (Abca) (Release To Other Than Dod Requires Prior Approval Of Hq Darcom Drcird

QSTAG-101 ED.A - Standardization Of 2 Inch Fuze Holes And Fuze Contours For Artillery Projectiles 75Mm And Larger In Caliber Including 81Mm, 4. 2 Inches And 107Mm Mortars

QSTAG-105 - Sampling Procedures And Tables For Inspection By Attributes (Abca-105)

The Armies of the United States, United Kingdom and Australia and the Canadian Forces have standardized sampling procedures and tables for inspection by attrihutes.

QSTAG-108 ED.1 - Link, Cartridge, Metallic Belt 7.62Mm, M13 (Including Amendments 1 Thru 6)

QSTAG-109 ED.1 - Interchangeability Criteria For Batteries, Storage (Batteries, Secondary) (Lead - Acid Type)

QSTAG-111 ED.1 - U.S. Printing Press, Offset (Lithographic, Motor Driven, Mobile).And U.K. Machine Printing, Rotary, Lithographic, Offset, Two Colour (Abca-111)

QSTAG-112 - Water Purification Unit Van Body Mounted, Electric Motor-Driven, Erdlator-Type Clarifier, Diatomite Type Filters, 1500 Gph (Abca-112)

QSTAG-113 - Specification For Ce (Tetryl)-(Abca-113)

QSTAG-114 - Specification For Picrite (Nitroguanidine)-(Abca-114)

QSTAG-115 - Specification For Rdx (Hexogene)-(Abca-115)

QSTAG-116 - Specification For Petn (Penthrite)-(Abca-116)

QSTAG-117 - Specification For Ammonium Nitrate (For Use In Explosives)-(Abca-117)

QSTAG-118 - Specification For Tnt (Tolite) Abca-118

QSTAG-121 ED.1 - Rules Governing The Interchangeability Of Securing And Holding Devices For Infrared Scopes On Carbines, Rifles And Light Machine-Guns (Abca-121

QSTAG-122 ED.1 - Lamps For Tactical Vehicles (Abca-122)

QSTAG-123 ED.2 - Small Arms Ammunition (7.62Mm)

The subject of this agreement is functional interchangeability of 7.62mm ammunition.

QSTAG-125 ED.2 - Charger For Nato 7.62 Mm Ammunition (Based On Nato Stanag 2318) (Abca 125)

The subject of this agreement is functional interchangeability of the Charger for the 7.62MM Ammunition.

QSTAG-128 ED.1 - Interchangeability Of Infrared Equipment Mounted On Portable Infantry Weapons Optical Alignment Of The Telescope (Abca-128)

QSTAG-129 ED.2 - Standardization Of Inpact Tests For Steel For Guns (Based On Nato Stanag 4020) (Abca 129)

QSTAG-13 ED.2 - Immersion Requirement For Ground Role Service Equipment (Based On Nato Stanag 2842) (Abca) Edition 2

The aim of this agreement is to establish criteria for the immersion of applicable equipment used by the ABCA forces when operating in a ground role.

QSTAG-130 ED.1 - Nato Symbol Of Interchangeability (Abca-130)

STANAG-3510 ED.3 - The Provision Of Hydraulic Power For Servicing Aircraft Hydraulic Systems

The aim of this agreement is to standardize the essential charateristics of power driven hydraulic servicing equipment to facilitate cross-servicing of aircraft.

STANAG-3514 ED.3 - Aircraft Main Batteries

The aim of this agreement is to provide the standards for aircraft batteries to facilitate interchangeability and thereby enhance the effectiveness of aircraft cross-servicing.

STANAG-3516 ED.5 - Electromagnetic Interference, Test Methods For Aircraft Electrical And Electronic Equipment

The primary aim of this agreement is to foster international co-operation and commonality between participating nations concerning the control of electromagnetic interference (both emission and susceptibility characteristics) and the achievement of electromagnetic compatibility of electrical and electronic equipment, including ground support equipment, for use with aircraft systems. To this end, this document establishes and documents the desired test methods required to evaluate the above equipment.

STANAG-3518 ED.4 - Environmental Test Methods

The aim of this agreement is to standarize the process of designing tests for the effect of climate and man-made environment on aircraft equipment.

STANAG-3525 ED.6 - Safety Design Requirements - Airborne Fuzing Systems

The aim of this agreement is to standardize safety design requirements for fuzing systems, including safety and arming devices for airborne weapons.

STANAG-3526 ED.7 - Interchangeability Of Nato Aircrew Medical Categories

STANAG-3527 ED.2 - Aircrew Flying Time And Rest Periods

STANAG-3530 ED.6 - Radio And/Or Navigational Aid Failure Procedures For Operational Air Traffic (Oat) Flights

STANAG-3531 ED.8 - Safety Investigation And Reporting Of Accidents/Incidents Involving Military Aircraft, Missiles And/Or Uavs

STANAG-3532 ED.5 - Transport Of Troops By Helicopter

STANAG-3533 ED.9 - Flying And Static Displays - Afsp-5 Edition A

STANAG-3534 ED.5 - Airfield Portable Lighting

STANAG-3535 ED.1 - Heliport Marking And Lighting

The aim of this agreement is to establish a heliport marking and lighting system for Visual Meteorological Conditions (VMC) and Instrument Meteorological Conditions (IMC) and day marking of serviceable runways and taxiways for heliports.

STANAG-3543 ED.5 - Air Transport Cargo/Passenger Handling Systems - Request For Information

STANAG-3544 ED.3 - Aircraft Lamps

The aim of this agreement is to standardize the characteristics of general and special purpose aircraft lamps to facilitate cross-servicing.

STANAG-3545 ED.2 - Characteristics Of Breathable Liquid Oxygen

The aim of this agreement is to ensure minimal acceptable characteristics of breathing liquid oxygen provided for aircraft cross-servicing purposes.

STANAG-3546 ED.4 - Liquid Nitrogen Characteristics

The aim of this agreement is to ensure minimum acceptable characteristics of liquid nitrogen provided for aircraft cross-servicing purposes.

STANAG-3547 ED.3 - Characteristics Of Replenishment Equipment For Liquid Nitrogen

The aim of this agreement is to ensure minimum acceptable characteristics for equipment employed for the cross-servicing of aircraft of air launched missiles with liquid nitrogen.

STANAG-3548 ED.3 - Tie-Down Fittings On Air Transported And Air-Dropped Equipment And Cargo Carried Internally By Fixed Wing Aircraft

STANAG-3552 ED.9 - Search And Rescue Manual - Atp-10(D)

STANAG-3554 ED.2 - Standard Visual Aerodrome And Heliport Traffic Patterns And Associated R/T Phaseology

STANAG-3556 ED.5 - Aircraft Store Ejector Cartridge

STANAG-3557 ED.1 - Standard Nato Safety Tests For Airborne Pyrotechnic Stores For Fixed Wing Aircraft And Helicopters

The air of this agreement is to standardize rough handling, vibration and climatic tests applied to all airborne pyrotechnic stores.

STANAG-3558 ED.5 - Locations Of Electrical Connectors For Aircraft Stores

STANAG-3564 ED.3 - Rules For Live Air Weapons Demonstrations

The aim of this agreement is to ensure that all factors affecting the safe conduct of any live air weapons demonstrations are adequately studied and to specify responsibilities for the planning and conduct of such demonstrations.

STANAG-3568 ED.1 - Aircraft Gaseous Systems Replenishment Connections (With Amendments 1 Thru 5 Incorporated)

STANAG-3569 - Replenishment Equipment For Air Ventilated Suits And Adaptors

The aim of this agreement is to permit the air ventilated suite of each nation's aircrew to be connected to other member nation's ground air supply equipment.

STANAG-3570 ED.3 - Drop Zones And Extraction Zones - Criteria And Markings

The aim of this agreement is to establish the criteria for and marking of Drop Zones and Extraction Zones used during tactical air transport operations.

STANAG-3571 - Classification, Certification And Labelling Of Dangerous Cargo (With Amendments 1 Thru 5 Incorporated)

To establish the classification, certification and labels to be used in the transport of dangerous cargo.

STANAG-3572 ED.3 - Exchange Of Information On Tactical Air Transport Operations

The aim of this agreement is to establish a method of exchanging information on tactical air transport operations.

STANAG-3575 ED.5 - Aircraft Stores Ejector Racks

STANAG-3576 ED.5 - Electrical Connector For Dispensers And Internal Intervalometer Type Rocket Launchers For Aircraft

The aim of this agreement is to establish a common electrical interface for future dispenser and internal intervalometer type rocket launchers for aircraft.

STANAG-3583 ED.3 - Standards Of Accuracy For Differential Pressure Gauges For Aviation Fuel Filters And Filter Separator Vessels

STANAG-3591 ED.6 - Criteria For Maximum Elevation Figure For Aeronautical Charts

STANAG-3593 ED.4 - Numbering Of Engines And Their Associated Control And Displays In Aircraft

The aim of this agreement is to standardize the numbering of engines and their associated controls and displays in aircraft.

STANAG-3595 ED.5 - Aircraft Fitting For Pressure Replenishment Of Gas Turbine Engines With Oil

STANAG-3597 ED.3 - Helicopter Tactical Or Non Permanent Landing Sites

STANAG-3599 ED.2 - Edge Numbering Of Films Used For Air Reconnaissance

STANAG-3600 ED.3 - Topographical Land Maps And Aeronautical Charts 1:250,000 For Joint Operations

STANAG-3601 ED.3 - Criteria For Selection And Marking Of Landing Zones For Fixed Wing Transport Aircraft (Including Amendment 6)

The aim of this agreement is to standardize the criteria for selection and marking of Landing Zones (LZ) for fixed wing aircraft in tactical air transport operations, but excluding LZ used for Special Forces operations.

STANAG-3603 - Pressure Replenishment Connection For Methanol/Water And De-Mineralised Water

STANAG-3605 ED.4 - Compatibility Of Arming Systems And Expendable Aircraft Stores

STANAG-3606 ED.6 - Laser Safety Evaluation For Outdoor Military Environments ?√ Arsp-4

STANAG-3609 ED.5 - Standards For Maintenance Of Fixed Aviation Fuel Receipt, Storage And Dispensing Systems

STANAG-3610 ED.3 - Characteristics Of Conditioned Breathable Air Supplied To Aircraft On The Ground

STANAG-3611 ED.2 - Characteristics Of Compressed Breathing Air

The aim of this agreement is to standardize compressed breathing air characteristics.

STANAG-3614 ED.5 - Electromagnetic Environmental Effects (E 3 ) ?√ Requirements For Aircraft Systems And Equipment

The aim of this agreement is to establish a general guideline for electromagnetic environmental effects (E 3) requirements to be followed during E 3 system design to ensure safe and effective operation of an aircraft and its installed electrical, electronic and electromechanical equipment during NATO exercises for the life of the aircraft.

STANAG-3616 ED.3 - Responsibility For The Design And Provision Of Adaptors Necessary For The Compatibility Of Air Cargo Loading, Securing, Unloading Or Dropping Systems In Fixed Wing Aircraft

STANAG-3617 ED.1 - Planning Procedures For Small Scale Tacticalair Transport Operations

The aim of this agreement is to standardize the planning procedures for small scale tactical air transport operations to permit units to operate successfully together.

STANAG-3619 ED.5 - Helipad Marking And Lighting

STANAG-3622 ED.3 - External Vision From Aircrew Stations

The aim of this agreement is to standardize the quality and extent of external vision from aircrew stations.

STANAG-3624 ED.5 - Nitrogen And Replenishment Equipment Characteristics

STANAG-3625 ED.4 - Aircraft Lockwire

STANAG-3626 ED.4 - Circular Dial Barometric Altimeters (Imperial And Metric)

The aim of this agreement is to standardize the display and physical characteristics of all circular dial barometric (pressure) altimeters, particular requirements for special types of altimeter, and their calibration procedures.

STANAG-3627 ED.3 - Helicopter Day And Night Tactical Formation Flying

The aim of this agreement is to establish procedures for helicopter tactical formation flying.

STANAG-3628 ED.5 - Helicopter Tactical Refuelling

The aim of this agreement is to standardize refuelling procedures for rotary wing aircraft in a tactical environment.

STANAG-3630 ED.2 - Emplaning And Deplaning At The High Hover

The aim of this agreement is to standardize methods and procedures to be adopted when troops and cargo are to be lowered from or recovered to a helicopter at the high hover.

STANAG-3631 ED.2 - Wartime Air Movement Priority System For Nato Countries

The aim of this agreement is to provide for a wartime air priority system to facilitate and assure the timely movement of military traffic between operational theatres.

STANAG-3632 ED.5 - Aircraft And Ground Support Equipment Electrical Connections For Static Grounding

The aim of this agreement is to standardize the electrical connections for static grounding, methods and procedures to be used on aircraft and Ground Support Equipment (GSE) to safely dissipate static charges and ensure personnel safety during aircraft servicing and ground handling.

STANAG-3634 ED.3 - Runway Friction And Braking Conditions

The aim of this agreement is to standardize the friction calibration and verbal descriptions of runway surface conditions.

STANAG-3635 ED.4 - Aircraft Stores Suspension Units With Gravity Release Capability

STANAG-3636 ED.3 - Airspeed Indicators (Imperial And Metric)

The aim of this agreement is to standardize the display, physical and performance characteristics for airspeed indicators which are used to display indicated airspeed of an aircraft in knots or km/h using pitot-static pressure inputs.

STANAG-3637 ED.2 - Attitude Indicators (Self-Contained And Remote Driven)

The aim of this agreement is to establish the display and physical requirements for Attitude Indicators.

STANAG-3639 ED.5 - Aircrew Station Dimensional Design Factors

STANAG-3640 ED.4 - Attitude Director Indicators

The aim of this agreement is to establish standard case size, display, physical and electrical requirements for Attitude Director Indicators which are used to display aircraft attitude and director/command information.

STANAG-3642 ED.3 - Single Frequency Approaches

To establish common procedures for single frequency approaches for single piloted aircraft.

STANAG-3643 ED.2 - Coating, Reflection Reducing For Glass Elements Used In Aircrew Station Displays

STANAG-3646 ED.1 - Characteristics Of Supply Equipment For Breathable Compressed Air

STANAG-3647 ED.3 - Nomenclature In Aircrew Stations

STANAG-3648 ED.2 - Electronically And/Or Optically Generated Aircraft Displays For Fixed Wing Aircraft

The aim of this agreement is to standardize electronically and/or optically generated displays which provide flight and combat information.

STANAG-3649 ED.1 - Essential Sar Characteristics Of Personnel Parachutes

To define the essential characteristics of personnel parachutes.

STANAG-3650 ED.2 - Essential Sar Location Equipment And Associated Characteristics (Aircraft)

STANAG-3652 ED.2 - Helipad Lighting (Vmc) (S/S By Stanag-3619)

The aim of this agreement is to establish a system of helipad lighting for visual meterological conditions (VMC).

STANAG-3660 ED.2 - Aircraft Main Battery Electric Plug

STANAG-3662 ED.1 - 16 Mm Film Cores

The aim of this agreement is to standardize design criteria and functional parameters for 16 mm film cores used by the NATO Armed Forces.

STANAG-3663 - Drinking Water Pressure Replenishment Connections

To standardize the drinking water pressure replenishment connection fitted to aircraft.

STANAG-3666 ED.3 - Maximum Sizes For Maps, Aeronautical Charts And Other Geospatial Products (Excluding Nautical Charts)

STANAG-3667 ED.1 - Dimensions Of Aircraft Accessory Drives And Mounting Pads

STANAG-3671 ED.3 - Edition Designation System For Land Maps, Aeronautical Charts And Military Geographic Documentation

The aim of this agreement is to standardize the system of edition designation of land maps, aeronautical charts and military geographic documentation (MGD) to be used by the NATO Armed Forces in order that the use of identical maps, charts and documentation by these forces may be facilitated.

STANAG-3672 ED.2 - Indexes To Series Of Land Maps And Aeronautical Charts, Digital Geographic Information, And Military Geographic Information And Documentation (Mgid)

STANAG-3673 ED.4 - Identification Of Source Data On Nautical And Special Naval Charts

STANAG-3675 ED.2 - Symbols On Land Maps, Aeronautical And Special Naval Charts

STANAG-3676 ED.3 - Marginal Information On Land Maps, Aeronautical Charts And Photomaps

STANAG-3677 ED.3 - Standard Scales For Land Maps And Aeronautical Charts

The aim of this agreement is to standardise the scales for land maps and aeronautical charts.

STANAG-3678 ED.3 - Method Of Adding The Military Grid To Nautical Charts In The Nato Area

The aim of this agreement is to standardize the method of adding the military grid to nautical charts in the NATO area.

STANAG-3680 ED.5 - Nato Glossary Of Terms And Definitions (English And French) - Aap- 6

STANAG-3681 ED.3 - Criteria For Pressure Fuelling/Defuelling Of Aircraft

STANAG-3682 ED.5 - Electrostatic Safety Connection Procedures For Aviation Fuel Handling And Liquid Fuel Loading/Unloading Operations During Ground Transfer And Aircraft Fuelling/Defuelling

STANAG-3684 ED.2 - Helipad Lighting (Imc)

The aim of this agreement is to establish a system for heliped approach lighting for Instrument Meteorological Conditions (IMC).

STANAG-3685 ED.3 - Airfield Portable Marking

STANAG-3686 - Planning Procedures For Small Scale Tactical Air Transport Operations

STANAG-3687 ED.3 - Camouflage Of Aircraft

The aim of this agreements is to establish general rules of camouflage for certain aircraft types earmarked or assigned to NATO.

STANAG-3688 ED.4 - Characteristics Of Breathable Oxygen Supplied By Chemical Solid Generators

The aim of this agreement is to define the minimum acceptable characteristics for breathable oxygen supplied by chemical solid generators for aeronautical use in emergency.

STANAG-3690 ED.2 - Maximum Trimmed Paper Size Of Maps For Use In The Field

The primary aim of this agreement is to standardize the maximum trimmed paper size of maps produced by NATO nations for their armed forces engaged in ground operations.

STANAG-3691 ED.2 - Circular Dial Tachometers (Non-Servoed) Compatible With Two-Pole Three-Phase Generators

The aim of this agreement is to provide a standard for one type of circular dial non-servoed tachometers, compatible with two-pole three-phase generators, for use on turbine-engined aircraft.

STANAG-3692 ED.1 - Location And Actuation Of Thrust Vector Controls For Vstol Aircraft Other Than Rotary Wing Aircraft

STANAG-3694 ED.1 - Delivery Safety Of High Explosive Bombs For Fixed Wing Aircraft

STANAG-3699 ED.1 - Dimension Of Elastomeric O Rings For Aircraft (Metric Series)

STANAG-3701 ED.4 - Aircraft Interior Colour Schemes

STANAG-3702 ED.1 - Essential Sar Location Equipment To Be Carried In Aircraft

STANAG-3703 ED.8 - Air Maritime Co-Ordination (Amc) - Ajp-3.3.3 (Atp-34)

STANAG-3705 ED.3 - Human Engineering Design Criteria For Controls And Displays In Aircrew Stations

STANAG-3710 ED.1 - Military City Maps

STANAG-3711 ED.3 - Airfield Marking And Lighting Colour Standards

STANAG-3712 ED.7 - Aircraft Rescue And Fire-Fighting Services - Identification Categories

STANAG-3714 ED.2 - Streamers, Warning

STANAG-3715 ED.2 - Specifications For Filing And Charting Of Non-Sub Contacts (Nsc) Information

STANAG-3716 ED.2 - Land Map Series Numbering

The aim of the Agreement is to standardize the series numbering system for military land maps (to exclude aeronautical charts) to facilitate the use of identical maps by the NATO Forces.

STANAG-3719 - Radar Relief Models

STANAG-3721 ED.3 - Automatic Data Processing (Adp) Master File For Land Maps And Aeronautical Charts

STANAG-3726 ED.5 - Bail (Portal) Lugs For The Suspension Of Aircraft Stores

STANAG-3727 ED.2 - Saddle Lugs For The Suspension Of Airborne Stores

STANAG-3731 ED.5 - Bibliography On Electromagnetic Compatibility (Emc)

STANAG-3732 ED.2 - Recognition Training

STANAG-3736 ED.11 - Allied Joint Doctrine For Close Air Support And Air Interdiction- Ajp-3.3.2(A)

STANAG-3737 ED.1 - Height Bands - Airdrop

STANAG-3738 ED.2 - Personnel Parachutes

STANAG-3739 ED.4 - Combined Air Terminal Operations

STANAG-3740 ED.3 - Procedures For Tracing Air Transported Baggage And Missing Air Transported Cargo

The aim of this agreement is to adopt standard procedures in order to trace lost or found air baggage, provide uniform description of lost or found air baggage, report air cargo delivery discrepancies, and dispose of unclaimed baggage.

STANAG-3741 ED.4 - Horizontal Situation Indicators (Hsi) (No S?S Document)

The aim of this agreement is to standardize the display, electrical, physical and performance requirements of HSIs which are used to display aircraft heading, course, distance to a reference point, deviation from course or track and other navigational and directional information.

STANAG-3742 ED.1 - Circular Dial Engine Temperature Indicators

The aim of this agreement is to standardize the characteristics of circular dial engine temperature indicators for use in turbine-engined aircraft where the input is derived from thermocouples.

STANAG-3744 ED.3 - Minimum Requirements Of Medical Equipment In Search And Rescue (Sar) Aircraft

The aim of this agreement is to establish a standard list of minimum medical equipment to be used by the NATO military SAR aircrafts.

STANAG-3745 ED.4 - Medical Training And Equipment Requirements For Search And Rescue (Sar) And Combat Search And Rescue (Csar) Missions

STANAG-3746 ED.2 - Minimum Essential First-Aid And Survival Equipment In Aircraft

The aim of this agreement is to establish standard minimum lists of first-aid and survival equipment to be carried in all NATO aircraft.

STANAG-3747 ED.10 - Guide Specifications (Minimum Quality Standards) For Aviation Turbine Fuels (F-34, F-35, F-40 And F-44)

STANAG-3748 ED.4 - Hydraulic Fluids, Petroleum (H-515, H-520 And C-635) And Polyalphaolefin (H-537, H-538 And H-544)

STANAG-3750 ED.6 - Reporting And Investigation Of Air Traffic Incidents

STANAG-3751 ED.1 - Dimensions Of Tapped Holes For Wire Thread Inserts (Metric Series)

STANAG-3752 ED.2 - Witness (Breaking) Wire For Aircraft Emergency Controls And Equipment

STANAG-3753 ED.3 - The Transportation And Utilities Compatibility Of Mobile Reconnaissance Support Shelters

STANAG-3754 ED.2 - Automatic Data Processing (Adp) War Reserve Stock File For Maps And Aeronautical Charts

The aim of this agreement is to standardize the ADP logical record to be used for the detail file for the management and control of war reserve map and aeronautical chart stocks at the standard scales.

STANAG-3756 ED.4 - Facilities And Equipment For Receipt And Delivery Of Aviation Kerosene And Diesel Fuels

STANAG-3758 ED.3 - Signals Used By Air Traffic Service Units For Control Of Pedestrian And Vehicular Traffic In The Manoeuvring Area Of Airfields

STANAG-3759 ED.9 - Nato Supplement To Icao Doc 8168-Ops/611, Volume Ii, For The Preparation Of Instrument Approach And Departure Procedures - Aatcp-1(D)

STANAG-3763 ED.1 - Electrical Connectors For Rocket Launchers For Rotary Wing Aircraft

STANAG-3764 ED.4 - Exchange Of Imagery

The aim of this agreement is to establish the format and national points of contact for requesting imagery.

STANAG-3765 ED.1 - Pressure Replenishment Of Aircraft Engine Oil

The aim of this agreement is to standardize minimum required facilities for Pressure Replenishment of Aircraft Engine Oil.

STANAG-3766 ED.3 - Grease Nipples

STANAG-3767 ED.2 - Exchange Of Data On Load Capabilities Of Transport Aircraft

The aim of this agreement is to provide a standardized format for the exchange of data on the load capabilities transport aircraft when this information is requested by member nations.

STANAG-3769 ED.2 - Minimum Resolved Object Sizes And Scales For Imagery Interpretation

STANAG-3770 ED.2 - Air Transport Baggage Tags

STANAG-3771 ED.3 - Ground Security Measures Against Aircraft Sabotage/Hijacking

The aim of this agreement is to adopt standard ground security measures against potential hijacking or sabotage of NATO air transport aircraft involved in combined airlift operations.

STANAG-3774 ED.4 - Control Procedures For Pallets And Associated Restraint Equipment Used In Combined Air Transport Operations

STANAG-3775 ED.3 - Air Movement And In-Transit Storage Of Cargo Requiring Controlled Temperature Conditions

The aim of this agreement is to standardize procedures for the air movement and in-transit storage of special cargo requiring controlled temperature conditions.

STANAG-3776 ED.2 - Marginal Information On Landmaps, Aeronautical Charts & Photomaps

STANAG-3777 ED.2 - Airdrop Of Door Bundles With Sticks Of Parachutists From Fixed Wing Aircraft

The aim of this agreement is to adopt as standard a procedure for the airdrop of door bundles with sticks of parachutists.

STANAG-3778 ED.2 - Performance Criteria For Honeycomb Paper Used As Energy Dissipating Material

STANAG-3780 - Calibration Certificate For Mapping Cameras

The aim of this agreement is to standardize the minimum essential elements of information to be contained in a mapping camera calibration certificate.

STANAG-3782 - Terrain Flight With Helicopters

STANAG-3783 ED.4 - Air Weapons Ranges - Identification Of Control Installations And Spectator Sites During Daylight Operations

STANAG-3784 ED.5 - Technical Guidance For The Design And Construction Of Aviation And Ground Fuel Installations On Nato Airfields

STANAG-3791 ED.7 - Interoperability Of Nato Aircraft And Stores - Aop- 11

STANAG-3794 - Identification Of Aircraft Electrical Cables

The aim of this agreement is to specify the way in which single-core cables (wires) used in the wiring of aircraft shall be marked as to type, size, origin, date, etc., in order to facilitate servicing, the investigation of faults and replacement, when necessary, with an equivalent cable.

STANAG-3800 ED.2 - Night Vision Imaging System (Nvis) Interior Lighting Compatibility Design Criteria

The aim of this agreement is to provide design criteria for interior aircrew station lighting in order to achieve Night Vision Imaging System (NVIS) compatibility.

STANAG-3802 ED.4 - Screwdriver Recesses (High Performance)

STANAG-3805 ED.9 - Allied Joint Doctrine For Airspace Control - Ajp-3.3.5 Edition B

STANAG-3806 ED.2 - Aircraft High Pressure Gaseous Nitrogen Systems Replenishment Connectors

The aim of this agreement is to specify the mating and access clearance dimensions of high pressure gaseous nitrogen replenishment couplings for aircraft.

STANAG-3809 ED.4 - Digital Terrain Elevation Data (Dted) Exchange Format

STANAG-3811 ED.1 - Runway Friction Standards

The aim of this agreement is to standardize the friction calibration of runways in order to ensure a common standard both for the dissemination of information and for the initiation of runway surface repairs.

STANAG-3817 ED.5 - Standard R/T Phraseology To Be Used For Air Traffic Control

STANAG-3821 ED.1 - Chaff And Ir Cartridges For Aircraft

The aim of this agreement is to standardize the design of Chaff and IR Cartridges and to collect unclassified design data about these cartridges to achieve standardization where practicable.

STANAG-3824 ED.2 - Guide Specification (Minimum Quality Standards) For Aviation Gasoline (F-18)

The aim of this agreement is to provide a document (a guide specification) which establishes the minimum quality standards of aviation gasolines used in service operations by NATO forces.

STANAG-3827 ED.5 - Minimum Requirements For Physiological Training Of Aircrew In High ?⌠G?÷ Environment

STANAG-3828 ED.1 - Minimum Requirements For Aircrew Protection Against The Hazards Of Laser Target Designators

The aim of this agreement is to standardize the terminology, procedures, and equipment used to protect aircrew who are at risk from the visual hazards associated with laser target designators.

STANAG-3830 ED.2 - Aircrew Nuclear Flash Blindness Protection

STANAG-3833 ED.3 - Symbols For Use On Maps Of Training Areas For Land Forces

STANAG-3834 ED.1 - Data Annotation For Air Reconnaissance Imagery

STANAG-3836 ED.3 - Microform

The aim of this agreement is to assure uniformity of dimensions, image placement and orientation for microforms used by NATO nations so as to enhance the exchange and utilization of data and information between nations.

STANAG-3837 ED.6 - Aircraft Stores Electrical Interconnection System

STANAG-3838 ED.4 - Digital Time Division Command/Response Multiplex Data Bus

STANAG-3847 ED.2 - Helicopter In-Flight Refuelling (Hifr) Equipment

STANAG-3854 ED.3 - Policies And Procedures Governing The Air Transportation Of Dangerous Cargo

STANAG-3859 ED.4 - Standardized Data List For Interoperability Studies And Certification Of Aircraft Stores

The aim of this agreement is to establish the data required for aircraft/store interoperability studies and for certification or flight trails of externally carried non-nuclear aircraft stores.

STANAG-3861 ED.5 - Heliport Rescue And Fire-Fighting Services - Identification Categories

STANAG-3864 ED.1 - The Measurement Of Protection Provided To The Respiratory Tract And Eyes By Aircrew Equipment Assemblies Against Nbc Agents In Particulate, Aerosol And Vapour Form

STANAG-3865 ED.2 - Physiological Requirements For Aircraft Molecular Sieve Oxygen Concentrating Systems

STANAG-3867 ED.1 - Helmets Damaged In Service, Collection Of Data For Evaluation Of

STANAG-3869 ED.1 - Aircrew Station Control Panels

STANAG-3870 ED.2 - Emergency Escape/Evacuation Lighting

The aim of this agreement is to standardize emergency/escape lighting which aids aircraft occupants in escape from aircraft in abnormal situations.

STANAG-3872 ED.2 - Rate Of Fuel Flow Indicators

The aim of this agreement is to establish certain standard requirements for rate of fuel flow indicators.

STANAG-3879 ED.8 - Wildlife Strike Prevention - Afsp-1.4 Edition A

STANAG-3880 ED.6 - Allied Joint Doctrine For Counter-Air Operations?√ Ajp-3.3.1(B)

STANAG-3881 ED.2 - Fuels To Be Introduced Into And Delivered By The North Italian Pipeline System (Nips)

STANAG-3884 ED.2 - Air Imagery Interpretation Annotation

STANAG-3887 ED.1 - Trial Reports And Design Criteria For In-Shelter Fuelling And Damage Repair - Aflp-3

STANAG-3888 ED.1 - Fuels To Be Distributed By The Uk Pipeline System (Ukps)

STANAG-3892 ED.4 - Apron Floodlighting

The aim of this agreement is to establish parameters to govern the design and installation of apron floodlighting.

STANAG-3896 ED.5 - Aerospace Emergency Rescue And Mishap Response Information (Emergency Services)

STANAG-3898 ED.5 - Aircraft Stores Interface Manual (Asim) - Aop-12

The aim of this agreement is to register national acceptance and annual updating of AOP-12.

STANAG-3899 ED.2 - Ground Fit And Compatibility Criteria For Aircraft Stores

STANAG-3900 ED.1 - Emc Of Airborne Electro Explosive Sub-Systems

STANAG-3906 ED.1 - Reporting Of Aircraft Accident Statistics

STANAG-3907 ED.1 - Cross Servicing Of Helicopters Engaged In Land Operations

STANAG-3908 ED.2 - Standardized Avionics Terminology And Abbreviations - Aap-33

STANAG-3909 ED.3 - Discrete Signal Interfaces

The aim of this agreement is to achieve easier development, improved maintenance and a decrease in life cycle costs of avionic systems by using standardized electrical characteristics of four types of discrete signal interfaces as dictated by system requirements. Later editions of this agreement may include other discrete signal types when they are defined.

STANAG-3912 ED.5 - Ada - Real-Time High Order Computer Programme Language

STANAG-3917 ED.2 - Air Conditioning Connections, Ground Half Connectors

The aim of this agreement is to standarize air conditioning half connectors on the ground servicing equipment for air conditioning the aircraft and its installed equipment to facilitate aircraft cross-servicing and NATO interoperability.

STANAG-3920 ED.3 - Handbook For Air Reconnaissance Tasking And Reporting - Atp-47(A)

The aim of this agreement is to register national acceptance and annual updating of ATP-47(A).

STANAG-3922 ED.3 - Airdrop Systems For Personnel And Supply/Equipment - Atp-46(A)

STANAG-3929 ED.5 - Evaluation Guide For Nato Crash/Fire/ Rescue Services

STANAG-3932 ED.2 - Air Launched Weapons Designed For Ready Use Storage (All-Up-Round)

The aim of this agreement is to establish a common objective to design air-launched weapons such that these weapons can be stored in an assembled condition ready for aircraft load.

STANAG-3940 ED.3 - Characteristics Of Aircraft Colour Cathode Ray Tubes

STANAG-3943 ED.3 - Physiological Requirements For Aircrew Cbrn Defence Assemblies Used In Flight

STANAG-3947 ED.1 - Ground Half Air And Electrical Connectors For Low Pressure Air Starting Of Aircraft Engines

The aim of this agreement is to standardize a ground half conector for low pressure air starting of aircraft engines.

STANAG-3948 ED.3 - Towing And Steering Devices For Aircraft

The aim of this agreement is to standardize the form and essential dimensions of the attachment heads on otwing and steering bars used for normal towing, and to provide compatibility of hooks on towing bridles used for alternative methods of towing.

STANAG-3950 ED.2 - Helicopter Design Criteria For Crew Crash Protection And Anthropometric Accommodation

STANAG-3957 ED.3 - C/Atlas Hol For Application In Avionics Test Systems

STANAG-3961 ED.1 - Application Form For Overflight And Landing Clearance

STANAG-3967 ED.1 - Design And Performance Requirements For Aviation Fuel Filter Separator Vessels And Coalescer And Separator Elements

STANAG-3968 ED.3 - Nato Glossary Of Air Electrical And Electromagnetic Terminology

STANAG-3971 ED.7 - Air-To-Air Refuelling Atp-56 - Atp-3.3.4.2 Edition C

STANAG-3977 ED.4 - Manual Of Techniques Of Sampling And Analysis Of Gases And Liquefied Gases For Aircraft Servicing - Aep-6

STANAG-3979 ED.1 - Parachute Extraction Assemblies

The aim of this agreement is to establish common characteristics for parachute extraction assemblies.

STANAG-3981 ED.2 - Minimum Physiological Requirements For Immersion Protection Assemblies For Aircrew

STANAG-3982 ED.1 - Messages Supplement To Atp-27 - Offensive Air Support Operations

The aim of this agreement is to register national acceptance of ATP-27 Supp.1.

STANAG-3983 ED.1 - Messages Supplement To Atp-34 - Tactical Air Support For Maritime Operations

The aim of the agreement is to register national acceptance of ATP-34 Supp. 1.

STANAG-3985 ED.1 - Preferred Magnetic Tape Standards For The Exchange Of Digital Geographic Information

The aim of this agreement is to standardize the specifications of magnetic tapes which are to be used for the exchange of digital geographic information.

STANAG-3986 ED.1 - Digital Data File Transmittal Form For Geographic Information

The aim of this agreement is to standardize the form which accompanies the transmittal of every geographic data file recorded on a magnetic tape.

STANAG-3988 ED.1 - Fuels To Be Distributed By The Uk Pipeline System (Ukps)

STANAG-3990 ED.1 - Characteristics Of High Quality Oil-Free Gaseous Nitrogen, Supply Pressure And Hoses, For Aircraft Weapons And Electronic Equipment Servicing

The aim of this agreement is to define the essential characheristics of a high quality oil-free gaseous nitrogen suitable for servicing aircraft, weapons and electronic equipment; to specify agreed supply pressures; and to specify the essential characteristics of the supply hoses.

STANAG-3991 ED.2 - Design Criteria To Minimize Generation Of Static Electricity Within Aircraft Fuel Systems

The aim of this agreement is to provide design criteria to minimize the generation of static electricity within aircraft fuel systems.

STANAG-3992 ED.2 - Mgd - Terrain Analysis - Ageop-1(A)

The aim of this agreement is to register national acceptance of AGeoP-1(A).

STANAG-3993 ED.4 - Air Control Terms And Definitions - Aap-49

STANAG-3994 ED.2 - Application Of Human Engineering To Advanced Aircrew Systems

The aim of this agreement is to establish criteria for the application of human engineering considerations in the design, development and evaluation of advanced aircrew systems.

STANAG-3995 ED.2 - Marking Of Portable Fire Extinguishers

The aim of this agreement is to standardize the marking of portable fire extinguishers with respect to the method of operation and the types of fire for which the extinguisher is suitable.

STANAG-4003 ED.1 - Rules For The Conversion Of United States Industrial Drawings For Countries Employing The Metric System

The purpose of this Agreement is to standardize (a) The rules for the conversion of the dimensions shown on drawings of military equipment parts and more generally on US industrial drawings; (b) the rules for preparing, keeping up to date and distributing converted drawings when the task of preparing these drawings is entrusted to a pilot country or firm.

STANAG-4004 ED.1 - Pneumatic Types For Transport Vehicles

The object of this Agreement is to achieve interchangeability of pneumatic tyres for wheeled transport vehicles listed in AC/225 (Panel 1)D/16 (Revised) dated 23 May 1969.

STANAG-4005 ED.1 - Head Light Unit For Wheeled Tactical Vehicles No S/S Document)

The aim of this agreement is to standerdize the overall dimensions of the headlamp light unit on tactical wheeled vehicles.

STANAG-4008 ED.1 - Lamps For Tactical Vehicles

STANAG-4009 ED.2 - Interface Geometry, Tractors And Semi-Trailers

The aim of this agreement is to standardize the interface geometry of tractors and semi-trailers in order to have interoperability when coupling NATO Armed Forces tractors and semi-trailers of different national origin.

STANAG-4012 - Type Designation And Marking Of Electron Valves And Tubes

The purpose of this agreement is to ensure that electron valves and tubes used in military equipment for NATO Armed Forces and complying with the same (agreed) specification (see STANAG 4013) are identified by the same type designation(s) and are marked accordingly by all NATO nations.

STANAG-4013 - Use Of Common Specification For Type/Qualification Approval And Procurement Of Electronic Valves/Tubes

STANAG-4015 ED.3 - Starter Battery Spaces For Tactical Land Vehicles

STANAG-4016 ED.1 - By-Pass Oil Filters And Corresponding Oil Filter Elements For Wheeled Tactical Vehicles

STANAG-4019 ED.2 - Emergency Towing Facilities (Superseded By Stanag 4478)

STANAG-4020 ED.2 - Impact Tests At Low Temperature For Steel For Guns

The object of this Agreement is to standardize certain low temperature impact tests for steel for guns, so that a common quality assessement can be arrived at to meet the operational requirements and specifications of the NATO Armed Forces.

STANAG-4022 ED.4 - Explosives, Specification For Rdx (Hexogene)

STANAG-4023 ED.5 - Explosives, Specification For Penthrite (Petn)

The aim of this agreement is to ensure that pentaerythritol tetranitrate (PETN, Penthrite) shall possess properties which make it suitable for military use and to provide, within NATO, an acceptable basis for the procurement and certification of PETN.

STANAG-4024 ED.3 - Ammonium Nitrate (An)(For Use In Explosives) Physical And Chemical Requirements, Specifications

STANAG-4025 ED.3 - Specification For Tnt (Tolite) For Deliveries From One Nato Nation To Another

STANAG-4026 ED.3 - Explosives, Specification For Nitroguanidine (Picrite)

STANAG-4031 ED.1 - Magnetic Cores, C-Type, Silicon Iron, For Transformers And Inductors

STANAG-4035 ED.1 - Rigid Rectangular Waveguides

STANAG-4037 ED.2 - Specification For A 40/70 Ammunition

STANAG-4038 ED.1 - Specification For A 40/70 Ammunition Operational Box (Metal) For Naval Use

STANAG-4040 ED.1 - Water Proof Electrical Connectors

The object of this agreement is to standardize the dimensions and essential characteristics of the waterproof electrical connectors (for lighting, ignition, starting and auxiliary equipment circuits) used on tactical vehicles of the armed forces of the North Atlantic Treaty Organization.

STANAG-4042 ED.1 - Rules For The Conversion Of United States Aeronautical Drawings (Air Frames) For Countries Employing The Metric System

The purpose of this agreement is to standardize the rules for the conversion of dimensions shown on drawings of airframes of United States origin.

STANAG-4043 ED.1 - Cooling System Hoses For Wheeled Transport Tactical Vehicles

The purpose of this Stanag is to facilitate physical inter-changeability of the cooling system hoses for wheeled transport tactical vehicles in the armed forces of the North Atlantic Treaty countries.

STANAG-4044 ED.2 - Adoption Of A Standard Atmosphere (Including Amendment 1)

The object of this Agreement is to adopt a common standard atmosphere for all NATO purposes.

STANAG-4050 ED.2 - Symbols Designating Function Of Controls In Military Vehicles

STANAG-4059 - Dry Batteries

The object of this agreement is to standardize a range of general purpose dry batteries to meet the bulk of requirements for these items in the design and construction of new equipment for use by the NATO Armed Forces.

STANAG-4061 ED.4 - Adoption Of A Standard Ballistic Meteorological Message

The aim of this agreement is to define a ballistic meteorological message and to standardize the number of its information digits and their meanings for use by any artillery service to any country.

STANAG-4062 ED.5 - Slinging And Tie-Down Facilities For Lifting And Tying Down Military Equipment For Movement By Land And Sea

STANAG-4079 ED.1 - Design Of 40/70 Ammunition

The purpose of this agreement is to standardize the minimum requirements for a design of 40/70 ammunition in order to ensure functional and operational interchangeability by NATO Naval and Army Forces in battle.

STANAG-4081 ED.1 - Specification For A Lightweight 40/70 Ammunition Operational Box

The purpose of this agreement is to standardize the minimum requirements for a lightweight 40/70 ammunition operational box.

STANAG-4093 ED.4 - Mutual Acceptance By Nato Member Countries Of Qualification Of Electronic And Electrical Components For Military Use

STANAG-4097 ED.1 - Procedures With Respect To Change Adjustment For Velocity For Standardized Gun Ammunition

STANAG-4098 ED.3 - Procedures For The Determination Of Propellant Charge Temperature Corrections

STANAG-4099 ED.1 - Specification Of, & Procedure For Checking Compliance With Pressure Limits For Standardized Gun Ammunition

STANAG-4100 ED.1 - Ballistic Surveillance Of Gun Ammunition

STANAG-4101 ED.2 - Towing Attachments

STANAG-4103 ED.4 - Format Of Requests For Meteorological Messages For Ballistic And Special Purposes

STANAG-4107 ED.8 - Mutual Acceptance Of Government Quality Assurance And Usage Of The Allied Quality Assurance Publications (Aqap)

STANAG-4110 ED.4 - Definition Of Pressure Terms And Their Interrelationship For Use In The Design And Proof Of Cannons Or Mortars And Ammunition

STANAG-4113 ED.3 - Pressure Measurement By Crusher Gauges

STANAG-4114 ED.3 - Measurements Of Projectile Velocities

STANAG-4115 ED.2 - Definition And Determination Of Ballistic Properties Of Gun Propellants

STANAG-4116 - Anti Tank Gun & Its Associated Ammunition 84Mm Carl Gustav Infantry

STANAG-4117 ED.3 - Explosives, Stability Test Procedures And Requirements For Propellants Stabilized With Diphenylamine, Ethyl Centralite Or A Mixture Of Both

STANAG-4119 ED.2 - Adoption Of A Standard Cannon Artillery Firing Table Format

STANAG-4120 ED.1 - Nato Electronic Parts Recommendations (Aetp-2) And Nato Electronic Technical Recommendations (Aetp-3)

STANAG-4123 ED.3 - Determination Of The Classification Of Military Ammunition And Explosives - Aastp-3

STANAG-4131 ED.2 - Adoption Of A Standard Character-By-Character Meteorological Message Format (Including Amendment 2)

The aim of this agreement is to standardize the layout of the Meteorological Messages designated in paragraph 3 below, both in punched tape and hard copy format.

STANAG-4134 ED.2 - Electrical Characteristics Of Rotating 28-Volt Dc Generating Sets (W/Amendment 2 Incorporated)

The aim of this agreement is to standardize certain electrical characteristics of rotating 28-volt DC generating sets for NATO forces in order to permit interoperability.

STANAG-4135 ED.2 - Electrical Characteristics Of Rotating Alternating Current Generating Sets (W/Amendment 1 Incorporated)

STANAG-4136 ED.1 - 20 Mm X 139 Ammunition For Ground/Air Defence Weapons

STANAG-4139 ED.1 - Criteria For Balancing Of Shipboard Rotating Machinery

STANAG-4140 ED.2 - Adoption Of A Standard Target Acquisition Meteorological Message

STANAG-4143 ED.1 - Ship/Shore Connection Terminals For 3-Phase Ac Power

STANAG-4144 ED.2 - Procedures To Determine The Fire Control Inputs For Use In Indirect Fire Control Systems

STANAG-4145 ED.2 - Nuclear Survivability Criteria For Armed Forces Material And Installations - Aep-4

STANAG-4146 - Nato Naval Data Handling Equipments, Interim Standard Specifications For Input/Output Interfaces In

STANAG-4147 ED.2 - Chemical Compatibility Of Ammunition Components With Explosives (Non-Nuclear Applications)

STANAG-4148 ED.1 - Standard Method To Be Used In Specifying And Evaluating Performance Accuracies Of Airborne Doppler Ground Velocities Sensors

STANAG-4151 ED.1 - Standard Colours For Indicating Lights

The aim of this agreement is to cover the main kinds of alarm and informative conditions for ships services on board ships of NATO navies with a limited number of indicating lights.

STANAG-4153 ED.1 - Standard Specification For An Asynchronous Serial Data Interface For Point To Point Connections And For Connection To Data Networks In Nato Naval Systems

STANAG-4154 ED.3 - Common Procedures For Seakeeping In The Ship Design Process

STANAG-4155 ED.1 - Nbc Protective Mask And Filter Canister Screw Threads

STANAG-4156 ED.1 - Standard Specification For A Serial Data Interface For Synchronous Connections To A Data Network

The aim of this agreement is to define standard design criteria for a digital data interface which is intended to be used to interconnect equipment in shipboard naval data handling systems.

STANAG-4157 ED.2 - Fuzing Systems: Test Requirements For The Assessment Of Safety And Suitability For Service

The aim of this agreements is to standardize the assessment of fuzing systems, to which the design requirements of STANAG 4187 are applicable, to support the appraisal of their safety, suitability and interchangeability within NATO forces.

STANAG-4158 ED.1 - Guidelines For Classifying Incidents For Reliability Estimation Of Tracked And Wheeled Vehicles

STANAG-4159 ED.2 - Nato Materiel Configuration Management Policy And Procedures For Multinational Joint Projects

STANAG-4164 ED.2 - Test Procedures For Armour Perforation Tests Of Armour Defeating Ammunition

The aim of this agreement is to standardize the test procedures for armour perforation tests of direct fire armour defeating ammunition.

STANAG-4165 ED.1 - Allied Material Standards Publications

The aim of this agreement is to promote the use of Allied Material Standards Publications (ASTanPs) relating to ACSM material and the development, updating and application of these ASTanPs.

STANAG-4170 ED.3 - Principles And Methodology For The Qualification Of Explosive Materials For Military Use

STANAG-4174 ED.3 - Allied Reliability And Maintainability Publications

STANAG-4177 ED.3 - Codification - Uniform System Of Data Acquisition

The aim of this agreement is to provide the policy for execution of a uniform system of data acquisition for use by the armed forces of the NATO countries and by NATO Agencies in Codification.

STANAG-4184 ED.3 - Microwave Landing System (Mls)

STANAG-4186 ED.1 - Interim Standard For A Parallel Digital Interface Between User Units & A Ship Distribution Network For Voice Communication

STANAG-4187 ED.4 - Fuzing Systems - Safety Design Requirements

STANAG-4190 ED.2 - Test Procedures For Measuring Behind-Armour Effects Of Anti-Armour Ammunition

STANAG-4194 ED.1 - Standardized Wave And Wind Environments And Shipboard Reporting Of Sea Conditions

STANAG-4196 ED.1 - Characteristics For An Aircraft Inertial Navigation System

STANAG-4197 ED.1 - Modulation And Coding Characteristics That Must Be Common To Assure Inter-Operability Of 2400 Bps Linear Predictive Encoded Digital Speech Transmitted Over Hf Radio Facilities

STANAG-4198 ED.1 - Parameters And Coding Characteristics That Must Be Common To Assure Interopera-Bility Of 2400 Bps Linear Predictive Encoded Digital Speech

STANAG-4199 ED.4 - Codification - Uniform System Of Exchange Of Materiel Management Data

STANAG-4202 ED.2 - Transmission Envelope Characteristics For High Reliability Data Exchange Between Land Tactical Data Processing Equipment Over Single Channel Radio Links

STANAG-4203 ED.3 - Technical Standards For Single Channel Hf Radio Equipment

STANAG-4204 ED.3 - Technical Standards For Single Channel Vhf Radio Equipment

STANAG-4205 ED.3 - Technical Standards For Single Channel Uhf Radio Equipment

STANAG-4206 ED.3 - The Nato Multi-Channel Tactical Digital Gateway - System Standards

STANAG-4208 ED.2 - The Nato Multi-Channel Tactical Digital Gateway - Signaling Standards

STANAG-4210 ED.2 - The Nato Multi-Channel Tactical Digital Gateway - Cable Link Standards

STANAG-4211 ED.2 - The Nato Multi-Channel Tactical Digital Gateway - System Control Standards

STANAG-4212 ED.2 - The Nato Multi-Channel Tactical Digital Gateway - Radio Relay Link Standards

STANAG-4213 ED.3 - The Nato Multi-Channel Tactical Digital Gateway - Circuit Switched Data Transmission Standards

STANAG-4214 ED.2 - International Routing And Directory For Tactical Communications Systems

STANAG-4217 ED.1 - Standard Specification For Digitized Video Data Representation

STANAG-4218 ED.1 - Accelerometer Test Procedure For An Aircraft Inertial Navigation System

The aim of this agreement is to define the functional specification (including performance) for Accelerometer Test Procedures to be used in support of an inertial navigation system applicable to aircraft including heleicopters.

STANAG-4219 ED.1 - System Test Procedure For An Aircraft Inertial Navigation System

The aim of this agreement is to define the functional specification (including performance) for an inertial navigation system applicable to aircraft including helicopters.

STANAG-4220 ED.1 - Specification Format Guide And Test Procedure For Single-Axis Laser Gyros

The aim of this agreement is to define a specification format quide for use in the preparation of laser gyro specifications and to provide recommended procedures for the testing of laser gyros used in inertial navigation systems.

STANAG-4222 ED.1 - Standard Specification For Digital Representation Of Shipboard Data Parameters

STANAG-4235 ED.2 - Electrostatic Discharge Environment

The aim of this agreement is: a. to define the electrostatic environment which may be experienced by all materiel utilized by the NATO Forces; and b. to define the electrostatic levels to be used as design criteria for all materiel intended for use by the NATO Forces.

STANAG-4240 ED.2 - Liquid Fuel/External Fire, Munition Test Procedures

STANAG-4241 ED.2 - Bullet Impact, Munition Test Procedures

STANAG-4244 ED.2 - Allied Foracs Publications

STANAG-4248 ED.1 - Purified Water For Submarine Main Lead Acid Batteries

STANAG-4249 ED.2 - Nato Standardized Profile - Connection-Oriented Mode Gateway Between Tactical Packet Switched Data Networks Using A Digital Data Circuit

STANAG-4250 ED.2 - Nato Reference Model For Open Systems Interconnection - Part 1: General Description

STANAG-4255 ED.1 - Nato Reference Model For Open Systems Interconnection - Layer 5 (Session Layer) Service Definition

STANAG-4256 ED.1 - Nato Reference Model For Open Systems Interconnection - Layer 6 (Presentation Layer) Service Definition

STANAG-4258 ED.1 - Nato Reference Model For Open Systems Interconnection - Specification Of Abstract Syntax Notation 1 (Asn.1)

STANAG-4259 ED.1 - Nato Reference Model For Open Systems Interconnection - Encoding Rules For Asn.1

STANAG-4265 ED.1 - Nato Reference Model For Open Systems Interconnection - Layer 5 (Session Layer) Protocol Specification

STANAG-4266 ED.1 - Nato Reference Model For Open Systems Interconnection - Layer 6 (Presentation Layer) Protocol Specification

STANAG-4270 ED.2 - Aviation Fuels For Future Nato Land Based Turbine Powered Military Aircraft

The aim of this agreement is to ensure that all future land based gas turbine powered military aircraft committed to NATO European Theatre operations shall be designed to use not only F-34 kerosene fuel, but also such other fuels as might reasonably be expected to be available in the absence in some future crisis of adequate supplies of F-34.

STANAG-4272 ED.2 - Nato Standard Methods Of Preservation

STANAG-4279 ED.1 - Nato Glossary Of Packaging Terms And Definitions - Aap-23

The aim of this agreement is to register national acceptance of AAP-23.

STANAG-4280 ED.2 - Nato Levels Of Packaging

STANAG-4281 ED.2 - Nato Standard Marking For Shipment And Storage

STANAG-4285 ED.1 - Characteristics Of 1200/2400/3600 Bits Per Second Single Tone Modulators/Demodulators For Hf Radio Links

STANAG-4286 ED.2 - Transducer Output

STANAG-4287 ED.1 - Electrolyte For Submarine Main Lead Acid Batteries

STANAG-4291 ED.1 - Modulation And Coding Characteristics That Must Be Common To Assure Interoperability Of 2400 Bps Wireline Modems For Use In Narrow-Band Secure Voice Systems

STANAG-4295 ED.1 - Significant Data & Telegraph Signalling Conditions

The aim of this agreement is to specify the significant data and telegraph signalling conditions for binary operation, for binary to quarternary conversion, for quarternary amplitude modulation and for four frequency diplex systems.

STANAG-4297 ED.2 - Guidance On The Assessement Of The Safety And Suitability For Service Of Non-Nuclear Munitions For Nato Armed Forces - Aop-15

STANAG-4317 ED.2 - Specification Of Common Characteristics For Fire Detection And Fire Fighting Systems For Future Main Battle Tanks

STANAG-4323 ED.1 - Specification Of Calcium Hypochlorite Used For Biological And Chemical Decontamination

STANAG-4324 ED.1 - Electromagnetic Radiation (Radiofrequency) Test Information To Determine The Safety And Suitability For Service Of Electro-Explosive Devices And Associated Electronic Systems In Munitions And Weapon Systems (Including Amendment 1)

The aim of this agreement is to specify the information to be provided to determine the electromagnetic (radio frequency) susceptibility of all new munitions and weapons systems containing electro-explosive devices being developed or produced for use by NATO forces.

STANAG-4325 ED.2 - Air-Launched Munitions Safety And Suitability For Service Evaluation

The aim of this agreement is to standardize the environmental and safety testing applied to an Air-Launched Munition (ALM), to support the appraisal of their safety and suitability for service in accordance with AOP-15, and to avoid unnecessary duplication of testing.

STANAG-4328 ED.2 - Guidelines To Improve Nuclear Radiation Protection Of Military Vehicles - Aep-14

STANAG-4329 ED.4 - Nato Standard Bar-Code Symbologies - Aap-44

STANAG-4330 ED.1 - Spheroid For Use In Maritime Tactical Data Handling Systems

STANAG-4331 ED.1 - The Specification For Evaluation Of The Accuracy Of Airborne Hybrid Navigation Systems

The aim of this agreement is to adopt a standard method of reporting the geodetic position accuracies of AIRBORNE HYBRID NAVIGATION SYSTEMS.

STANAG-4349 ED.1 - Measurement Of The Minimum Resolvable Temperature Difference (Mrtd) Of Thermal Cameras

STANAG-4355 ED.3 - The Modified Point Mass And Five Degrees Of Freedom Trajectory Models

STANAG-4357 ED.1 - Allied Vehicle Testing Publications (Avtps)

STANAG-4358 ED.1 - Mutual Acceptance Of Government Vehicle Test And Evaluation

STANAG-4359 ED.1 - Nato Handbook For The Sampling And Identification Of Chemical Warfare Agents - Aep-10

STANAG-4367 ED.3 - Thermodynamic Interior Ballistic Model With Global Parameters

STANAG-4385 ED.1 - 120 Mm X 570 Ammunition For Smooth-Bore Tank Guns

STANAG-4389 ED.1 - Terms And Definitions Covering Submarine Main Lead Acid Batteries

STANAG-4390 ED.1 - Tests And Requirements For Submarine Main Lead Acid Batteries

STANAG-4400 ED.1 - Derivation Of Thermochemical Values For Interior Ballistic Calculations

STANAG-4437 ED.1 - Electromagnetic Compatibility Testing Procedure And Requirements For Naval Electrical And Electronic Equipment (Submarines)

STANAG-4482 ED.1 - Standardised Information Technology Protocols For Distributed Interactive Simulation (Dis)

STANAG-5000 ED.3 - Interoperability Of Tactical Digital Facsimile Equipment

STANAG-5004 ED.2 - Military Characteristics For Field Telephone Sets (Minimum Standards) (Includes Amendments 1 Thru 4)

The aim of this document is to prescribe the minimum standard for field telephone sets for NATO Armed Forces.

STANAG-5013 ED.1 - Data Transmissions For Radar Doppler Navigation Systems

STANAG-5018 ED.1 - Nato Manual Interface Between The Manual Switched Telecommunications Systems Of The Combat Zone

STANAG-5020 ED.1 - Interoperability Of Aircraft Uhf Multifrequency Transceiver Installation & Compatible Ground Transmitters And Receivers

STANAG-5021 ED.3 - Military Characteristics For Ground & Surface Uhf Direction Finding Equipment

STANAG-5028 ED.2 - Significant Telegraph Signalling Conditions In Automatic Telegraphy

STANAG-5032 ED.1 - Basic Technical Characteristics For Single Sideband Single-Channel Voice Communications Between 1,5 And 30 Mhz In The Mobile Services

STANAG-5036 ED.3 - Parameters And Practices For The Use Of The Nato 7-Bit Code

STANAG-5037 ED.2 - Future Requirements For Number Of Morse Operators In Nato Naval Ships

The aim of this agreement is to enable nations to make plans for the scale of training of morse operators and for their availability in ships in the post-1980 period to permit effective operation of ships assigned to NATO.

STANAG-5040 ED.3 - Nato Automatic And Semi-Automatic Interfaces Between The National Switched Telecommunications Systems Of The Combat Zone And Between These Systems And The Nato Integrated Communications System (Nics) - Period From 1979 To The 1990S

STANAG-5042 ED.1 - Military Telecommunications-Diagram Symbols

STANAG-5045 ED.2 - Interoperability Characteristics For Teleprinters Using The Nato 7-Bit Code

STANAG-5046 ED.2 - The Nato Military Communications Directory System

STANAG-5048 ED.5 - The Minimum Scale Of Connectivity For Communications And Information Systems For Nato Land Forces

STANAG-5500 ED.7 - Concept Of Nato Message Text Formatting System (Conformets) - Adatp-3

STANAG-5550 - Nato Standard Data Elements, Data Items And Codes (Edition No. 1)

STANAG-5624 ED.1 - Nuclear, Biological And Chemical (Nbc) Event Prediction And Reporting Message Text Formats (Mtf)

STANAG-5801 ED.1 - Standard Data Elements/Data Chains, Data Items, Data Abbreviations And Data Codes For Nato Interservice Use In Automated Data Handling Systems

STANAG-6001 ED.4 - Language Proficiency Levels

STANAG-6002 ED.2 - Principles And Procedures For The Conduct And Financing Of Training Assistance

STANAG-6004 ED.3 - Meaconing, Intrusion, Jamming And Interference Report

STANAG-6005 ED.5 - Manpower Policies And Procedures - Aap-16(C)

STANAG-7005 ED.9 - Exchange Of Aeronautical Information Publication (Aip) And Flight Information Publication (Flip) Data

STANAG-7010 ED.2 - Provision Of Airfield Marking Information

STANAG-7011 ED.2 - Automated Fuel System Monitoring And Control Equipment

STANAG-7012 ED.3 - Minimum Radiotelephony (R/T) Aerodrome Departure Procedures

The aim of this agreement is to standardize procedures for use in times of crisis and war and peacetime exercises, which will permit aircrews to start up and take off their aircraft and follow Terminal Aerodrome Departure Procedures (TAPs)/Standard Instrument Departure Procedures (SIDs) with minimum R/T.

STANAG-7016 ED.4 - Maintenance Of Geographic Materials

STANAG-7017 ED.1 - Spectrometric Analysis Of Aircraft Engine Lubricants

STANAG-7021 ED.1 - Position Information Graphic (Pig)

STANAG-7025 ED.3 - Air Traffic Management And Control Of Minimum Operating Strips (Mos) Operations

STANAG-7028 ED.3 - Identical Aircraft For Aircraft Cross-Servicing

STANAG-7033 ED.2 - Allied Tactical Air Messages (Formatted And Structured) - App- 8(A)

STANAG-7035 ED.1 - Mapping, Charting And Geodesy (Mc&G) Video Disc

STANAG-7036 ED.4 - Fuels To Be Introduced Into And Delivered By The Nato Pipeline System (Nps)

STANAG-7047 ED.1 - Cfr Equipment And Procedures To Protect The Health And Safety Of Cfr Personnel During Operations

The aim of this agreement is to provide a standard of crash fire and rescue equipment and procedures to protect the health and safety of crash fire and rescue personnel during operations.

STANAG-7048 ED.3 - States Of Crash Fire Readiness

STANAG-7049 ED.3 - Personal Protective Equipment (Ppe) Requirements For Fire And Emergency Operations

STANAG-7052 ED.1 - Maintaining Aircraft Crash/Fire/Rescue Skills For Nato Fire- Fighters

STANAG-7054 ED.1 - Protected Areas Mapping (Pam)

STANAG-7066 ED.1 - Spool Towing Attacments On Aircraft

The aim of this agreement is to standardize the form and essential dimensions of the spool attachment points on aircraft for normal towing.

STANAG-7067 ED.3 - Type And Location Of 'Non-1760' Electrical Connectors For Helicopter Rocket Launchers

STANAG-7068 ED.2 - Aircraft/Stores Certification Procedures

STANAG-7074 ED.2 - Digital Geographic Information Exchange Standards (Digest)

STANAG-7079 ED.1 - Light Fittings For Airfield Visual Aids (Runway In-Pavement Lights) - Aep-12

very Equipment And Techniques For Helicopters

STANAG-2978 ED.1 - Essential Performance Characteristics Of Field Surgical Lights

STANAG-2979 ED.1 - Essential Characteristics Of Electro-Surgical Apparatus

STANAG-2980 ED.1 - Technical Criteria For External Cargo Carrying Nets

STANAG-2981 ED.1 - Prevention Of Cold Injury

STANAG-2984 ED.6 - Graduated Levels Of Chemical, Biological, Radiological And Nuclear Threats And Associated Protective Measures

STANAG-2989 ED.2 - Transfer Of Barriers

STANAG-2990 ED.1 - Principles And Procedures For The Employment In Land Warfare Of Scatterable Mines With A Limited Laid Life - Atp-50

STANAG-2991 ED.4 - Nato Combat Engineer Glossary - Aap-19(D)

STANAG-2999 ED.9 - Use Of Helicopters In Land Operations - Doctrine - Atp-49(F)

STANAG-3052 ED.5 - Aeronautical Briefing Facilities

The aim of this agreement is to establish the principles and basic criteria for the installation of aeronautical briefing facilities.

STANAG-3053 ED.6 - Characteristics Of Breathing Oxygen, Supply Pressure And Hoses

STANAG-3054 ED.5 - Characteristics Of Compressed Air For Technical Purposes, Supply Pressure And Hoses

STANAG-3056 ED.6 - Marking Of Airborne And Ground Gas And Cryogenic Fluid Containers

The aim of this agreement is to provide an agreed method of marking airborne and ground gas and cryogenic fluid containers utilized in cross-servicing operations.

STANAG-3093 ED.5 - Nato Air Transport Request & Answer To Air Transport Request (Narat & Transar)

The aim of this agreement is to standardize the format of messages for requesting air transport support for use within NATO Forces.

STANAG-3094 ED.1 - 16 Bit Computer Instruction Set Architecture

STANAG-3097 ED.1 - Short Take-Off & Landing (Stdl) Airfield Marking

The aim of this agreement is to establish the marking of Short Take-Off and Landing (STOL) airfields and runways.

STANAG-3098 ED.11 - Aircraft Jacking - Aassep-1 Edition A

STANAG-3101 ED.15 - Exchange Of Safety Information Concerning Aircraft And Missiles

STANAG-3102 ED.5 - Flight Safety Co-Operation In Common Ground/Air Space

The aim of this agreement is to establish the requirement for co-ordination of accident prevention matters.

STANAG-3104 ED.6 - Identificatiion Of Aircraft And Missile Pipelines And Electrical Conduits

STANAG-3105 ED.7 - Pressure Refuelling Connections And Defuelling For Aircraft - Aassep-2 Edition A

STANAG-3109 ED.5 - Symbol Marking Of Aircraft Servicing And Safety/Hazard Points

STANAG-3111 ED.2 - Airfield Marking Tone Down

STANAG-3114 ED.8 - Aeromedical Training Of Flight Personnel

STANAG-3117 ED.7 - Aircraft Marshalling Signals

The aim of this agreement is to standardize aircraft marshalling signals and the distinctive garment to be worn by aircraft marshallers.

STANAG-3146 ED.1 - Planning Procedures For Tactical Air Transport Operations

STANAG-3149 ED.10 - Minimum Quality Surveillance Of Fuels

STANAG-3150 ED.8 - Codification - Uniform System Of Supply Classification

The aim of this agreement is to provide a uniform system of supply classification for use by the Armed Forces of the NATO countries.

STANAG-3151 ED.9 - Codification - Uniform System Of Item Identification

STANAG-3153 ED.8 - Aircraft Navigation And Anti-Collision Lights

The aim of this agreement is to establish common requirements for aircraft navigation and anti-collision lights.

STANAG-3154 ED.2 - Aircraft Formation Lights (Edition No. 2)

The aim of this agreement is to standardize the styles and types of formation lights to permit the execution of the various formation operations safely without violating visual security.

STANAG-3156 ED.3 - Aircraft Paratroop Signal Lights

STANAG-3158 ED.7 - Day Marking Of Airfield Runways And Taxiways

STANAG-3159 ED.3 - Method Of Numbering Components Of Aircraft Engines

To standardize a method of numbering engine cylinders, combustion chambers, flame tubes, and similar components of all aircraft engines, in order to distinguish one from the other.

STANAG-3179 ED.6 - 16 Mm And 35 Mm Roll Film For Aerial Cameras

The aim of this agreement is to standardize the dimensions, tolerances, winding characteristics and labeling for 16 mm and 35 mm roll film for aerial cameras.

STANAG-3180 ED.3 - Sheet Photographic Paper For Air Photography (With Amendment 1 Incorporated)

STANAG-3181 ED.3 - Rolled Photographic Paper For Air Photography (With Amendment 1 Incorporated)

STANAG-3182 ED.3 - Nato High Contrast Developer (Edition N0. 3)

STANAG-3187 ED.3 - Labelling Of Pre-Packaged Photographic Chemicals

STANAG-3188 ED.3 - Negative Film Black And White For Air Photography

To standardize the classification of air films in accordance with defined methods of measuring their principal sensitometric and physical characteristics related to certain conditions of use.

STANAG-3198 ED.4 - Functional Requirements Of Aircraft Oxygen Equipment And Pressure Suits

STANAG-3200 ED.8 - Minimum Requirements For G Protective Sytems

STANAG-3205 ED.3 - Points Designation Template For Air Imagery

STANAG-3207 ED.3 - Aircraft Grounding Plug

STANAG-3208 ED.6 - Air Conditioning Connections

STANAG-3209 ED.5 - Tyre Valve Couplings

STANAG-3210 ED.3 - Grease Nipples

To standardize aircraft grease nipples.

STANAG-3212 ED.6 - Diameters For Gravity Filling Orifices

STANAG-3213 ED.2 - Angles Of Heads For Countersunk Rivets (With Amendments 1 And 2 Incorporated)

STANAG-3216 ED.5 - Layout Of Flight Data In Pilots Displays

The aim of this agreement is to standardize the layout of flight data in pilots' displays.

STANAG-3217 ED.6 - Operation Of Controls And Switches At Aircrew Stations

STANAG-3218 ED.6 - Location, Actuation And Shape Of Engine Controls And Switches

The aim of this agreement is to standardize the location, actuation and shape of all engine controls and switches in fixed and rotary-wing aircraft.

STANAG-3219 ED.4 - Location And Grouping Of Electrical Switches In Aircraft

To standardize the location and grouping of various electrical switches in aircraft so that a pilot can always expect to find switches for a particular service in the same cockpit area.

STANAG-3220 ED.4 - Location, Actuation And Shape Of Airframe Control For Fixed Wing Air- Craft

The aim of this agreement is to standardize the location, actuation and shape of airframe controls for fixed wing aircraft.

STANAG-3221 ED.6 - Automatic Flight Control System (Afcs) In Aircraft - Design Standards And Location Of Controls

The aim of this agreement is to standardize the AFCS panel and controller location, the nomenclature and other functional areas of AFCS.

STANAG-3223 ED.4 - Flight Documents Stowages In Crew Compartments

STANAG-3225 ED.4 - Location, Actuation & Shape Of Airframe Controls For Rotary Wing Aircraft

The aim of this agreement is to standardize the location, actuation and shape of airframe controls for rotary wing aircraft.

STANAG-3226 ED.2 - Policy On Supply Forms

STANAG-3230 ED.7 - Emergency Markings On Aircraft

STANAG-3231 ED.2 - Aden And Defa 30 Mm Gun Barrel Chambers For Aircraft

To standardize NATO 30 mm gun barrel chambers.

STANAG-3232 ED.2 - 30Mm Link For Aden And Defa Guns

STANAG-3236 ED.9 - Designation System For Aircraft And Designation Of Role Codes Of Aircraft

The aim of this agreement is to establish for NATO forces the method of designating aircraft and the role codes of aircraft.

STANAG-3237 ED.3 - Aperture Of Terminal Ring Or Link Of Aircraft Lifting Slings

STANAG-3240 - Pyrotechnic And Flashing Lamp Signals For Air Traffic Control

STANAG-3242 ED.4 - Gca Procedures And Associated R/T Phaseology

The aim of this agreement is to set forth common basic GCA procedures.

STANAG-3243 - Controlled D/F Descents (With Amendments 1, 2)

STANAG-3244 - Non-Directional Beacon (Ndb) Vhf Omni- Directional Range (Vor), Tacan And Radio Range Approaches

To standardize the procedure for NDB, VOR, TACAN and Radio Range approaches.

STANAG-3254 ED.3 - Loan Of Materiel For Test Purposes In Support Of Standardization, Research And Development

STANAG-3256 ED.2 - Power Supplies For Testing Airborne Electrical Equipment

STANAG-3258 ED.6 - Position Of Pilot Operated Navigation And Radio Controls

STANAG-3261 - Portrayal Of Global Navigation Grid And Associated Isogriv Information

STANAG-3275 ED.3 - Method Of Warning Own Aircraft Of (Suspected) Enemy Fighter Attacks

The aim of this agreement is to standardize the methods of warning own aircraft of (suspected) enemy fighter attacks.

STANAG-3276 ED.3 - National Air Statistical Co-Ordinators

STANAG-3277 ED.7 - Air Reconnaissance Request/Task Form

The aim of this agreement is to adopt a standard air reconnaissance request/task form for use by the NATO Forces.

STANAG-3278 ED.8 - Aircraft Towing Attachments And Devices

STANAG-3279 ED.3 - Emergency Towing Equipment

The aim of this agreement is to standardize the emergency towing fitting provided on aircraft.

STANAG-3281 ED.5 - Personal Locator Beacons

The aim of this agreement is to standardize the characteristics of Personal Locator Beacons to ensure compatibility amongst nations.

STANAG-3294 ED.4 - Aircraft Fuel Caps And Fuel Cap Access Covers

STANAG-3295 ED.7 - Horse Collar/Rescue Strop Type Helicopter Hoisting Gear

STANAG-3296 ED.3 - Aircraft Gaseous Oxygen Replenishment Couplings

STANAG-3297 ED.6 - Nato Standard Aerodrome And Heliport Ats Procedures

STANAG-3298 - Tacan Instrument Approach Criteria (With Amendments 1 And 2 Incorporated)

To standardize Obstruction Clearane Criteria which will be used by the Nato Armed Forces in the development of high and low altitude TACAN instrument approach procedures.

STANAG-3300 ED.6 - Nato Glossary Of Aircraft Armament Terms And Definitions (English And French) - Aap-46

STANAG-3302 ED.5 - Connectors For 28 Volts

The aim of this agreement is to establish standard external DC servicing power connections to aircraft.

STANAG-3303 ED.3 - Connectors For 115/200 Volts, 400 Hertz, 3 Phase, Ac Servicing Power (S/S By Stanag-7073)

The aim of this agreement is to standardize the external AC servicing power supply connectors (plugs and receptacles)

STANAG-3312 ED.4 - Profile Dimensions Of Flanges For V-Band Couplings For Piping And Ducting

STANAG-3313 ED.3 - Jacking Of Aircraft

The aim of this agreement is to standardize primary jacking requirements, including tyre and wheel changing.

STANAG-3314 ED.3 - Interchangeability Of Terminals (Lugs)

STANAG-3315 ED.8 - Aircraft Cabin Pressurizing Test Connections

STANAG-3316 ED.10 - Airfield Lighting

STANAG-3317 ED.5 - Aircraft Electrical Cables

To standardize a range of stranded flexible cables for general purpose use in aircraft to ensure interchangeability.

STANAG-3318 ED.7 - Aeromedical Aspects Of Aircraft Accident And Incident Investigation - Aamedp-1.7 Edition A

STANAG-3319 ED.6 - Dimensions For Cases Of Control Boxes, Instruments And Panel Mounted Equipment

STANAG-3320 ED.7 - Circular Dial Type Vertical Speed Indicators (Barometric)

The aim of this agreement is to standardize circular dial type vertical speed indicators fitted to aircraft.

STANAG-3322 ED.7 - Turn & Slip Indicators

The aim of this agreement is to standardize the main features of the presentation, performance and case size for turn and slip indicators.

STANAG-3323 ED.5 - Pipe (Tube) Connections To Aircraft Instruments (Imperial And Metric)

The aim of this STANAG is to establish standard dimensions for pipe (tube) connectors and adapters to aircraft instruments.

STANAG-3325 ED.3 - Detailed Procedures And Techniques For Forward Air Controlling (Supplement No. 1 To Atp-27(A)

STANAG-3326 ED.3 - Manifold Pressure Gauges

STANAG-3327 ED.2 - Air Transportation Of Dangerous Cargo

To standardize a procedure to permit explosives, radioactive materials and other dangerous cargo of one NATO nation to be carried in another NATO nations aircraft during emergency or war.

STANAG-3328 ED.2 - Nato Standard Conversion Tables For Metric, American And British Units Of Measurement, Aap-9 (With Amendments 1 Thru 4 Incorporated)

To standardize the conversion of Metric, American and British units of measurement by means of conversion tables.

STANAG-3329 ED.6 - Numerals And Letters In Aircrew Stations

STANAG-3330 ED.4 - Indicating Accelerometers

The aim of this agreement is to standardize the presentations, controls and case sizes of Indicating Accelerometers.

STANAG-3332 ED.3 - System For Tracing Missing Air Cargo

To standardize the procedure to be used by the NATO Armed Forces when discrepancies are noted on the delivery of air transported freight or equipment.

STANAG-3334 ED.4 - Defuelling Of Aircraft

The aim of this agreement is to ensure the provision of a selective aircraft defuelling capability and to establish standard practices which will facilitate the completion of defuelling operations.

STANAG-3337 - Indexes To Series Of Aeronautical Charts

STANAG-3338 ED.4 - Machmeters

The aim of this agreement is to establish standard case size, display and control features, minimum performance requirements and aircraft system interfacing for Machmeters.

STANAG-3339 ED.5 - Fuel Contents Gauges

The aim of the agreement is to establish the units of measurement and the features of presentation for fuel contents gauges.

STANAG-3341 ED.3 - Emergency Control Colour Schemes

The aim of this agreement is to adopt a standard colour scheme for emergency controls in aircraft.

STANAG-3344 ED.3 - Procedures For Tracing And Disposing Of Air Baggage (Baglo-Trobag)

To standardize procedures for tracing missing air baggage and disposing of found air baggage.

STANAG-3345 ED.6 - Data/Forms For Planning Air Movements

STANAG-3347 ED.5 - Identification Of Aircraft Electrical Circuits

STANAG-3350 ED.4 - Analogue Video Standard For Aircraft System Applications

STANAG-3359 ED.5 - Location And Arrangement Of Engine Displays In Aircraft

STANAG-3365 ED.2 - Suspension Units With Gravity Release Capability For Aircraft Stores

STANAG-3368 ED.3 - Internal Aircraft Engine Starting Systems

STANAG-3370 ED.6 - Aircrew Station Alerting Systems

STANAG-3372 ED.6 - Low Pressure Air And Associated Electrical Connections For Aircraft Engine Starting

STANAG-3374 ED.6 - Flight Inspection Of Nato Radio/Radar Navigation And Approach Aids - Aetp-1(D)

STANAG-3381 ED.1 - Nato Standard Procedures For Compensation And Form For Request And Receipt Of Support In The Form Of Supplies And Services

STANAG-3388 ED.1 - Airborne Radio Controlunits

STANAG-3390 ED.11 - Guide Specification And Inspection Standards For Fuel Soluble Lubricity Improvers (S-1747)

STANAG-3394 ED.3 - Angles Of Heads For Countersunk Screws

STANAG-3398 ED.3 - Air Pyrotechnics Interchangeability Chart

STANAG-3402 - Recovery And Release Of Parachutists Towed Behind Aircraft

STANAG-3405 ED.3 - Dimensions Of Clock Cases (With Amendment 1 Incorporated)

STANAG-3408 ED.3 - Position Reference Systems For Aeronautical Charts

STANAG-3409 ED.5 - Projections For Aeronautical Charts

STANAG-3411 - Base Symbols And Aeronautical Data For Aeronautical Charts

STANAG-3412 ED.6 - Aeronautical Information On Aeronautical Charts

The aim of this agreement is to define the essential aeronautical information to be portrayed on aeronautical charts for use within the NATO area of operational interest.

STANAG-3416 ED.5 - Methanol/Water And Demineralized Water Replenishment

STANAG-3418 ED.2 - Film Cores

The aim of this agreement is to standardize dimensions and design criteria for 16mm and 70mm film cores to permit interchangeability of film procured on cores.

STANAG-3419 ED.3 - Film Spools For Aerial Cameras

The aim of this agreement is to establish the specifications for film spools used in aerial cameras.

STANAG-3420 ED.3 - Photoflash Cartridges For Low Altitude Photography For Fixed Wing Aircraft

STANAG-3427 ED.4 - Colours For The Identification Of Airdropped Supplies

STANAG-3428 ED.6 - Exchange Of Information On Aerial Delivery Systems

STANAG-3436 ED.4 - Colours And Markings Used To Denote Operating Ranges Of Aircraft Instruments

STANAG-3440 ED.1 - Compatibility Of Air To Ground Rocket Launcher Systems For Fixed Wing Aircraft And Helacopters

STANAG-3441 ED.8 - Design Of Aircraft Stores

STANAG-3443 - Oil Compressed Nitrogen Characteristics Supply Pressure And Hoses

STANAG-3444 ED.2 - Dimensions Of Elastomeric O-Rings For Aircraft (Inch Series)

STANAG-3445 ED.1 - Dimensions Of Tapped Holes For Wire Thread Inserts (Inch Series)

STANAG-3446 ED.2 - Screwdriver Recesses (Low Torque Drive) Cross

The aim of this agreement is to standardize on the low torque driving recesses to be used for driving general purpose aircarft fasteners of up to 14mm shank diameter.

STANAG-3447 ED.3 - Aerial Refueling Equipment Dimensional And Functional Characteristics

STANAG-3448 ED.2 - Standard Synchro Electrical Characteristics For Aircraft Instruments

To standardize the electrial input characteristics of aircraft instruments driven from a remote synchro source to ensure to interchangeability of the instruments.

STANAG-3449 ED.2 - Vertical Scale Tape Indicating Flight 1Nstruments

STANAG-3451 ED.2 - Combined Speed Indicator

STANAG-3454 ED.6 - Ground Recharging Of Aircraft Main Batteries - Aaep-01 Edition A

STANAG-3455 ED.5 - Basic Symbols For Aircraft Electrical Circuits

STANAG-3456 ED.7 - Aircraft Electrical Power System Characteristics

STANAG-3459 ED.1 - Precision, High-Melting-Point, Cartridge Fuze Links Used On Aircraft

To facilitate cross-servicing of aircraft by standardizing the essential characteristics of precision, high-melting-point cartridge fuses as follows.

STANAG-3462 ED.4 - Availability Of Weight And Balance Requirements And Loading Criteria For Transport Aircraft

STANAG-3463 ED.1 - Planning Procedures For Tactical Air Transport Operations For Fixed Wing Aircraft

STANAG-3464 ED.3 - Procedures For Aircrew And Airlifted Personnel In Tactical Air Transport Operations

The aim of this agreement it to determine and standardize procedures to be followed in various NATO tactical and transport operations.

STANAG-3465 ED.5 - Safety, Emergency And Signalling Procedures For Military Air Movement - Fixed Wing Aircraft

The aim of this agreement is to establish safety, emergency and signalling procedures to be used when engaged in transporting personnel on joint air transport or airborne operations.

STANAG-3466 ED.3 - Responsibilities Of Air Transport Units And User Units In The Loading And Unloading Of Transport Aircraft In Tactical Air Transport Operations

STANAG-3467 ED.3 - Characteristics Of Air Transport (Air Landed) Pallets For Carriage Internally

STANAG-3468 ED.3 - General Rules Concerning The Transport Of Loads By Helicopter

The aim of this agreement is to establish general rules governing the transport of loads by helicopter to permit interoperability of helicopters.

STANAG-3469 ED.3 - Parachute Extraction Assemblies And Aircraft Extraction Parachute Ejector Installations

STANAG-3472 - Medical Protective Measures Associated With Missile Operations (With Amendment 1 Incorporated)

STANAG-3473 - Hearing Conservation (With Amendment 1 And 2 Incorporated)

STANAG-3474 ED.5 - Temporary Flying Restrictions Due To Exogenous Factors Affecting Aircrew Efficiency

STANAG-3487 - Metric Thread-Nuts, Bolts, Screws And Similar Parts (With Amendments 1 And 2 Incorporated)

STANAG-3491 ED.6 - Calibration & Accuracy Of Aircraft Barometric Altimeters (Imperal & Metric)

The aim of this agreement is to standrdize calibration procedures for aircraft barometric altimeters.

STANAG-3492 ED.5 - Clamps, Mounting (Imperial And Metric) For Aircraft Instruments

The aim of this agreement is to standardize the mounting clamps for flangeless instruments in order to facilitate interchanging of these instruments and to ensure their secure attachment.

STANAG-3495 ED.2 - Standard Pressure/Altitude Relationship Tables For Aircraft Equipment

To provide standard pressure/altitude values to be used in the design and calibration of those aircraft equipments whose operation is a function of atmospheric pressure.

STANAG-3497 ED.3 - Aeromedical Training Of Aircrew In Aircrew Cbrn Equipment And Procedures

STANAG-3499 ED.2 - Characteristics Of Supply Equipment For Liquid Oxygen

STANAG-3501 ED.3 - Performance Of Portable Filter-Blowers For Aircrew Cbrn Respirators

STANAG-3504 ED.2 - Cathode Ray Tube Head Down Displays (Monochrome)

AIR-STD-61/4 - Flotation And Sea Survival, Test Methods And Requirements

To standardize the requirements for inflatable life preservers.

AIR-STD-61/40 - A Technical Basis For Specifying The Insulation Of Immersion Protective Clothing

To standardize the technical basis upon which national guidelines to commanders may be drawn up in respect of the insulation requirements of immersion protective clothing.

AIR-STD-61/41 - Procedures For Calibration Of In-Flight Respiratory Data Acquisition Equipment

To define the procedures to be adopted for the calibration of equipment used in the acquisition of in-flight respiratory data.

AIR-STD-61/45 - Aviation Medicine/Physiological Training Of High Altitude Parachutists

To define the minimum aviation medicine/physiological training for high altitude parachutists.

AIR-STD-61/48 - Single Number Noise Reduction Of Hearing Protectors

The object of this AIR STD is to establish a method for calculating a single number moise reduction value to describe the overall performance of hearing protectors.

AIR-STD-61/5 - Escape Path Clearance In Ejection Seat Aircraft

AIR-STD-61/6 - Collection Of Data For Evaluation Of Helmets Damaged In Service (S/S By Air-Std-61/102)

To standardize the data collected from helmets damaged in service.

AIR-STD-61/7 - Minimal Protection For Aircrew Exposed To Altitudes Above 50,000 Feet

AIR-STD-61/73 - Minimum Standards For Breathing Equipment For Parachutists Between 13,000 & 25,000 Feet Pressure Altitude

AIR-STD-61/79 - Terminology Of Aeromedical Evacuation

AIR-STD-61/8 - Criteria For Reporting The Nature Of Clothing Materials On Assemblies Subjected To Physical & Operational Testing

AIR-STD-61/80 - Documentation Of Aeromedical Evacuation

AIR-STD-61/81 - Tests For Protective Capacity Of Fire Resistant Clothing Materials

AIR-STD-61/82 - Instrumentation For Escape System Thermal Hazard Analysis

AIR-STD-61/83 - A Basis For Common Practices And Goals In The Conduct Of Anthropometric Surveys

AIR-STD-61/84 - Initial Investigation And Immediate Management Of Laser Eye Injury In Aircrew

AIR-STD-61/9 - Protection Of Personnel Against The Effects Of High Levels Of Sound Upon Hearing & Operational Efficiency

AIR-STD-64/11 - Delineation Of Air Defense Identification Zones On Aeronautical Charts And Flight Information Publications

To ensure that Air Defense Identification Zones (ADIZ), when shown, are delineat4ed in the same manner on all aeronautical charts and Flight Information Publications.

AIR-STD-64/12 - Delineation Of The International Date Line On Aeronautical Charts And Flight Information Publications

To ensure that the placement of the International Date Line is the same on all aeronautical charts and Flight Information Publications.

AIR-STD-64/15 - Flight Information Publication, Enroute

To promote the standardization of Enroute Flight Information Publications produced by member nations to facilitate their use by any of the participating air forces.

AIR-STD-64/16 - Flight Information Publications - Planning

AIR-STD-64/18 - Title For Flight Information Publications

To standardize titles for Flight Information Publications (FLIP).

AIR-STD-64/19 - Explanatory Information Required On Aeronautical Charts

To identify the explanatory information to be shown on seronautical charts to satisfy the combined operational requirements of the member air force.

AIR-STD-64/20 - Operational Usage Criteria (S/S By Adv Pub 64/39)

AIR-STD-64/21 - Abbreviations And Code Legend Flight Information Publications 141166

AIR-STD-64/23 - Identification Of Scale On Aeronautical Charts

To enable participating air forces, by adoption of a common method, to identify without special instructions the scale of any aeronautical chart produced by any one of the air forces.

AIR-STD-64/24 - Symbols For Aeronautical Charts

To standardize the symbols used on aeronautical charts in order that air forces of one country may more easily use the aeronautical charts produced by participating nations.

AIR-STD-64/25 - Minium Content And Colour Of Aeronautical Information For Aeronautical Charts

AIR-STD-64/26 - Position Reference Systems For Aeronautical Charts

To identify a combined operational requirement to adopt basic position reference systems for use on aeronautical charts produced by participating nations.

AIR-STD-64/27 - Standard Scales For Topographic Aeronauticalcharts

To identify an operational requirement to adopt standard scales for topographic aeronautical charts produced by participating nations.

AIR-STD-64/28 - Definitions Of Aeronautical Map And Chart And Flight Information Terms

To establish a directory of terms and their definitions so that participating air forces may use without special instructions.

AIR-STD-64/29 - Aeronautical Chart Catalogues

AIR-STD-64/30 - Flight Information Publication Terminal

AIR-STD-64/31 - Identification Of Aerodrome By Name

To aid aircrew in the identification of aerodromes by the adoption of a common system for selecting the name under which the primary entry will appear in listings and on charts.

AIR-STD-64/32 - Aeronautical Chart Projections

AIR-STD-64/33 - Portrayal Of Navigation Grid Information

AIR-STD-64/34 - Identification Of Airspace Reservations (With Amendment 1)

AIR-STD-64/35 - Maximum Elevation Figure Criteria For Aeronautical Charts

To standardize the computation of Mximum Elevation Figures to be shown within the designated quadrangles on the aeronautical charts.

AIR-STD-64/36 - Aircraft Arresting Sysems, Information For Flips

To standardize the presentation of information related to aircraft arresting systems in enroute supplement and on instrument approach charts (terminal).

AIR-STD-64/37 - Flip Operational Abbreviations

To maintain a decode list of the operational abbreviations used in member nations' Flight Information Publications (FLIPS) and aeronautical charts.

AIR-STD-64/38 - Asw Dead Reckoning Tracker Plotting Charts

AIR-STD-64/6 - Standard Units Of Linear Measurement On Aeronautical Charts And Flight Information Publications (Req Other Than Dod Ref Hq Usaf/X0Xx-Iso, Washg., Dc 20330-5058 ( No S/S Document)

To identify standard units of linear measurement to be used on aeronautical charts and Flight Information Publications to satisfy the combined operational requirements of the member air forces.

AIR-STD-64/94 - Guidelines For The Assessment Of Thermal Stress In Aircraft Chemical Defense Operations

AIR-STD-65 - Changes To Ascc Air Standards/Advisory Publications - Working Party 65 - Airfield Marking & Lighting & Other Visual Aids

AIR-STD-65/1 - Lighting Of Instrument And Non-Instrument Runways

AIR-STD-65/10 - Airfield Lighting Control Systems

To standardize the airfield lighting control systems.

AIR-STD-65/11 - Illuminated Runway Distance Markers And Illuminated Hook Cable Markers

To achieve standardization between ASCC nations on Illuminated Runway Distance Markers (IRDM) and Illuminated Hookcable Marker (IHCM) as visual aids to aircraft operations at military airfields.

AIR-STD-65/12 - Airfield Lighting For Category 11 Operations

AIR-STD-65/13 - Extraneous Lighting In Vicinity Of Aerodromes

AIR-STD-65/14 - Airfield Marking And Lighting Color Standards

To establish standard colours for aeronautical ground light and surface markings.

AIR-STD-65/15 - Airfield Lighting Circuitry

AIR-STD-65/16 - Helipad Lighting (Vmc)

To establish a system of helipad lighting for Visual Meteorological Conditions (VMC).

AIR-STD-65/17 - Aerodrome Illuminated Markers And Signs

AIR-STD-65/18 - Apron Floodlighting

AIR-STD-65/19 - Standby Power Supply Requirements For Fixed Installations

AIR-STD-65/2 - Lighting Of Airfield Obstructions (Rel To Other Than Dod Act Req Pri Appr Of Hq Usaf/Xoxx-Iso Wash, Dc 20330-5058)

AIR-STD-65/21 - Helipad Marking

To standardize the markings of helipads at heliports, other than those heliports which use a runway for the helicopter landing area.

AIR-STD-65/22 - Airfield Clearance Planes

AIR-STD-65/23 - Aircraft Arresting Gears For Airfields

AIR-STD-65/24 - Air Traffic Control Procedures For Arrestment Of Aircraft

To ensure that each Member Nation using aircraft arresting systems of other Member Nations can expect Air Traffic Control to comply with a standard procedure.

AIR-STD-65/25 - Signals For Runway Party When Disengaging An Aircraft After A Hook Cable Arrestment

AIR-STD-65/26 - Pilots Operating Procedure For Engagement Of Airfield Arresting Systems (Issued Controlled)

The purpose of this ASCC AIR STD is to standardize pilot's procedure for engagement of airfield arresting systems.

AIR-STD-65/3 - Lighting And Marking Of Airfield Obstructions

To standardize the marking of airfield obstructions.

AIR-STD-65/30 - Pacific Nations Helicopter Operations From Ships Other Than Aircraft Carriers (Pac Hostac) Publications (Pac Hostac (Pac 1) And Pac Hostac Supplement (Pac 1-1)

To register national acceptance of PAC HOSTING (PAC 1) and PAC HOSTING Supplement (PAC 1-1).

AIR-STD-65/31 - Airfield Tone-Down Marking (S/S By Air-Std-65/36)

To standardize airfield tone-down markings.

AIR-STD-65/32 - Non-Tactical Heliport Lighting And Marking (Issued Controlled)

To establish heliport marking and lighting systems for visual meteorological conditions (VMC) and instrument meteorological (IMC) at heliports.

AIR-STD-65/33 - Airfield Declared Distances

To standardize the terminology and criteria for airfield declared distances.

AIR-STD-65/34 - Heliport And Helipad Lighting And Marking

The purpose of this agreement is to standardize lighting and marking of Heliports and Helipads.

AIR-STD-65/37 - Aircraft Arresting Systems Operating Procedures

AIR-STD-65/4 - Airfield Approach Lighting

AIR-STD-65/5 - Marking Of Instrument And Non-Instrument Runways (S/S By Air-Std-65/36)

AIR-STD-65/6 - Airfield Taxiway Markings (S/S By Air-Std-65/36)

AIR-STD-65/7 - Visual Glide Slope Indicator Systems

AIR-STD-65/8 - Airfield Portable Lighting Systems

AIR-STD-65/9 - Taxiway Lighting

AIR-STD-70/10 - Standard Analogue Heading Outputs

To establish scale factors and synchro voltages for the transmission of healing information.

AIR-STD-70/11 - The Specification For Evaluation Of The Accuracy Of Inertial Navigation Systems

To adopt a standard method of determining the position accuracies of pure Inertial Navigation Systems.

AIR-STD-70/13 - The Specification For Evaluation Of The Accuracy Of Airborne Doppler Navigation Systems

To adopt a standard method of determining the position accuracies of airborne doppler navigation systems.

AIR-STD-70/14 - Definition Of Sea State For Use In Connection With Doppler Navigation

AIR-STD-70/16 - The Specification For Evaluation Of The Accuracy Of Hybrid Navigation Systems

AIR-STD-70/17 - Definitions Of Aircraft Attitude And Heading Angles

The purpose of this agreement is to define the terminology used when referring to aircraft attitudes and manouevres.

AIR-STD-70/18 - Microwave Landing Systems (Mls)

AIR-STD-70/3 - Interoperability Of Aircraft Vhf Am And/Or Fm Multi-Frequency Transceiver Installations And Compatible Ground Radio Equipments

AIR-STD-70/4 - Interoperability Of Aircraft Uhf Multi-Frequency Transceiver Installation And Compatible Ground Transmitters And Receivers

AIR-STD-70/7 - Data Transmission For Radar Doppler Systems

To establish data transmission criteria for use in doppler radar systems.

AIR-STD-70/8 - True Airspeed Outputs

AIR-STD-80/1 - Method Of Determining The Principal Sensitometric Characteristics Of Black And White Rolled Air Film

AIR-STD-80/10 - Air Reconnaissance Request/Task Form

The purpose of this agreement is to standardize the format for requesting and tasking air reconnaissance by ASCC Armed Forces.

AIR-STD-80/11 - Titling Of Hand-Held Imagery (Wet)

AIR-STD-80/13 - Air Reconnaissance Intelligence Reporting Nomenclature

To standardize nomenclature for describing equipment and installations in imagery reports.

AIR-STD-80/14 - Point Designation Template For Imagery

To specify basic parameters to be observed in the construction of a universal grid for use in identifying a precise point of area on a frame of imagery.

AIR-STD-80/15 - Minimum Resolved Object Sizes For Imagery Interpretation

The purpose of this agreement is to specify minimum resolved object sizes required in imagery used for interpretation and technical analysis.

AIR-STD-80/18 - Reporting Of Data Used For Dimensional Analysis Of Imagery

The purpose of this agreement is to standardize the reporting of data used for dimensional analysis of imagery.

AIR-STD-80/3 - Dimensions, Tolerances And Characteristics Of 70Mm, 126Mm And 240Mm Rolled Film For Air Photography

To adopt standard dimensions, tolerances and characteristics for 70mm, 126mm, and 240mm rolled film for air photography, to permit the common use of film in cameras and processing equipment.

AIR-STD-80/5 - Target Pattern For Determination Of Aerial Photographic Resolution

The purpose of this agreement is to adopt a standard target pattern for determining the photographic resolution of aerial cameras used by ASCC nations during airborne operations.

AIR-STD-80/7 - Lm-230A/B Programmable Automatic Camera Test Set

AIR-STD-80/8 - Air Reconnaissance Intelligence Report Forms

To standardize and consolidate Air Reconnaissance Report Forms for reporting and presenting intelligence information derived from air reconnaissance and sensor imagery.

AIR-STD-84/11 - Casualty Handling In A Cw Environment

AIR-STD-84/12 - Peacetime Nuclear Weapons Accidents - Division Of Responsibilities

AIR-STD-84/13 - Peacetime Nuclear Weapons Accidents - Key Control Areas

AIR-STD-84/2 - Commander S Guide On The Effects Of Penetrating Ionizing Radiation (With Change 1)

To provide a standard method, within the ASCC member services, of categorizing the Radiation Exposure State of individuals, and groups of individuals, and to provide common guidance for Commanders.

AIR-STD-84/4 - First Aid Materiel For Chemical Injuries (With Change 1)

The purpose of this agreement is to standardize the minimum essential items of medical first-aid materiel for chemical injuries.

AIR-STD-84/9 - Nbc Defense Evaluation Of Air Bases

To identify the criteria for evaluating the effectiveness of Air Forces operating in an NBC environment.

AIR-STD-85/1 - Glossary Of Terms And Definitions

AIR-STD-90/4 - Aircraft Arresting Systems Information For Flips

The purpose of this agreement is to standardize the presentation of information related to aircraft arresting systems in enroute supplement and on instrument approach charts (terminal).

AIR-STD-94/3 - Comparative List Of Ascc Terms And Definitions For Nuclear Accident Response

To provide a comparative list of terms and definitions used by Member nations related to Nuclear Accident Response.

AOP-15 ED.3 - Guidance On The Assessment Of The Safety And Suitability For Service Of Non-Nuclear Munitions For Nato Armed Forces

AOP-16 ED.4 - Fuzing Systems: Guidelines For Stanag 4187

AOP-22 ED.1 - Design Criteria And Test Methods For Inductive Setting Of Electronic Projectile Fuzes

AOP-7 ED.2 - Manual Of Data Requirements And Tests For The Qualification Of Explosives Materials For Military Use

The primary objectives of this document are to promote standardization and interoperability of munitions among the NATO countries.

AOP-8 ED.2 - Nato Fuze Characteristics Catalogue

AQAP-100 ED.3 - Policy On An Integrated Systems Approach To Quality Through The Life Cycle

This document should be used, as a part of the overall policy of an organisation, to ensure quality of life cycle processes, products and services.

AQAP-11 - Nato Guideline For Specification Of Technical Publication

AQAP-110 ED.2 - Nato Quality Assurance Requirements For Design, Development And Production

AQAP-119 ED.2 - Nato Guide To Aqaps-110, -120, -130

AQAP-120 ED.2 - Nato Quality Assurance Requirements For Production

AQAP-130 ED.2 - Nato Quality Assurance Requirements For Inspection And Test

AQAP-131 ED.1 - Nato Quality Assurance Requirements For Final Inspection

AQAP-150 ED.2 - Nato Quality Assurance Requirements For Software Development Aqap-150

This publication specifies the project oriented requirements to manage the quality of the software development process.

AQAP-159 ED.2 - Guidance For The Use Of Aqap-150

This publication specifies the project oriented requirements to manage the quality of the software development process.

AQAP-170 ED.2 - Nato Guide For The Delegation Of Government Quality Assurance

AQAP-8 - Nato Guide To The Preparation Of Specifications For The Procurement Of Defence Material

ARMP-1 ED.4 - Nato Requirements For Reliability And Maintainability

ARMP-2 ED.2 - General Application Guidance On The Use Of Armp-1

ARMP-3 ED.2 - List And Source Of National And International Reliability And Maintenability Documents

ARMP-3 catalogues R&M Standards and other documents, military and civilian, which are produced by NATO countries.

ARMP-4 ED.4 - Guidance For Writing Nato R&M Requirements Documents

ARMP-6 ED.3 - Guidance For Managing In Service R & M

QAP-15 - Glossary Of Terms Usedin Proof (Rel To Other Than Dod Agencies Must Be Approved By Darcom, Drcde)

This QAP has been approved for use by the Armies of the United States, United Kingdom, and Australia and the Canadian Forces, as a Glossary of Terms used in Proof.

QAP-17 - Metallurical Terms & Definitions, Listing Of Glossaries Used By Armies (Req Other Than Dod Ref To Darcom, Drcde-1)

QAP-22 - Military Operations In Urban Terrain - Bibliography

QAP-9 - Engine Health Monitoring For Army Aircraft, Manual (Abca) (Release To Other Than Dod Requires Prior Approval Of Hq Darcom Drcird

QSTAG-101 ED.A - Standardization Of 2 Inch Fuze Holes And Fuze Contours For Artillery Projectiles 75Mm And Larger In Caliber Including 81Mm, 4. 2 Inches And 107Mm Mortars

QSTAG-105 - Sampling Procedures And Tables For Inspection By Attributes (Abca-105)

The Armies of the United States, United Kingdom and Australia and the Canadian Forces have standardized sampling procedures and tables for inspection by attrihutes.

QSTAG-108 ED.1 - Link, Cartridge, Metallic Belt 7.62Mm, M13 (Including Amendments 1 Thru 6)

QSTAG-109 ED.1 - Interchangeability Criteria For Batteries, Storage (Batteries, Secondary) (Lead - Acid Type)

QSTAG-111 ED.1 - U.S. Printing Press, Offset (Lithographic, Motor Driven, Mobile).And U.K. Machine Printing, Rotary, Lithographic, Offset, Two Colour (Abca-111)

QSTAG-112 - Water Purification Unit Van Body Mounted, Electric Motor-Driven, Erdlator-Type Clarifier, Diatomite Type Filters, 1500 Gph (Abca-112)

QSTAG-113 - Specification For Ce (Tetryl)-(Abca-113)

QSTAG-114 - Specification For Picrite (Nitroguanidine)-(Abca-114)

QSTAG-115 - Specification For Rdx (Hexogene)-(Abca-115)

QSTAG-116 - Specification For Petn (Penthrite)-(Abca-116)

QSTAG-117 - Specification For Ammonium Nitrate (For Use In Explosives)-(Abca-117)

QSTAG-118 - Specification For Tnt (Tolite) Abca-118

QSTAG-121 ED.1 - Rules Governing The Interchangeability Of Securing And Holding Devices For Infrared Scopes On Carbines, Rifles And Light Machine-Guns (Abca-121